Content |
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
|
| Product Features:
- 4 x 75 Watts into 4 Ohms; 4 x 50 Watts into 8 Ohms
- ATR (Accelerated Transient Response) technology for ultimate punch and clarity
- Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption
- Independent limiters for each channel offer maximum output level with reliable overload protection
- Detented gain controls for precise setting and matching of sensitivity
- Precise Power, Signal and Clip LEDs to monitor performance
- Servo-balanced XLR and 1/4" TRS inputs plus professional speaker connectors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front" ventilation system including air filter for reliable operation
- “Built-like-a-tank“, impact-resistant and all-steel 1U rackmount chassis
- Minimum depth chassis (10.1" / 257 mm) and ultra-light weight design (8.8 lbs / 4.0 kg) fits into compact, inexpensive effects racks
- High-quality components and exceptionally rugged construction ensure long life
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Amplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V) Analog Inputs 4, electronically balanced, Phoenix-type Audio Network No CAN Bus Interface Yes (With Optional RCM-810 Card) Continuous Rated Power (1 kHz, THD 1%) 100v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 2Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 4Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 70v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 8Ω 500 Watts Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans DIM 30 0.02 % Electronics Type Amplifier Frequency Response 15 Hz-30 kHz Input Impedance (Balanced) 20 kΩ Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V Intermodulation Distortion (SMPTE) 0.05 % Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz Network Control (IRIS-Net) Optional Total Harmonic Distortion 0.05 % Variable Load Drive (VLD) Yes Height 2RU 88.1 mm (3.47“) Width 483 mm (19.02“) Depth 421.5 mm (16.59“) Weight Net 11.1 kg (24.47 lbs)
| POWER AMPLIFIER 4 X 2100 WATT / 4Ω
Very high power and channel density – • The four-channel FP
10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in
only 2U
Four-channel fexibility – • Four channels in one cabinet increases
effciency, fexibility and value in powering monitor systems, line
arrays, and bi- or tri-amped systems. Adjacent channels bridgeable
for 2- or 3-channel operation
Lab.gruppen sound quality – • FP 10000Q amplifers maintain
the impeccable sonic performance standards set by the original fP
Series, with the same durability and even greater effciency
NomadLink • ® network ready – Monitoring and control of key
functions accessible via the intuitive DeviceControl software and
the robust, daisy-chained NomadLink® network
Patented Class TD amplifer topology – • Road-proven output
stage delivers Class B audio quality with Class D effciency
Regulated Switch Mode Power Supply (R.SMPS) – • Output
power remains constant even with signifcant drops in the mains
voltage
Effcient cooling system – • Unique, lightweight Intercooler® cop-
per cooling system dissipates more heat to allow extended peak
output
Adjustable parameters – • Selectable Gain, scalable Voltage Peak
Limiter (VPL), and bridge-mode operation allow custom confgura-
tion for any system or application
XLR input connectors •
Heavy-duty binding post or Speakon output connectors •
Comprehensive protection and warning – • Excessive output
current, DC, high temperature, very high frequency (VHF), short
circuit, open load, mains fuse protection, and soft start |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
Shipping Weight 15 lbs (6.8 kg)
Top
|
Reviews
There are no reviews yet.