Content |
D4175_MANUAL_GB_V1.pdf
HP-500
• Full protection circuits • Efficient forced air cooling • Stereo & Bridge mode
The DAP HP Series power amplifiers are the solution when true quality is needed in an affordable price range. The HP Series are 5 models representing output powers from stereo 200W until 1400W. All including the best protection circuits and built in a strong solid housing to achieve many years of reliable power. They are the best mobile choice for musicians, DJs, and entertainers but also perfect for installations in discos, pubs or any kind of public areas.
The HP Series power amplifiers by DAP Audio are the obvious choice for musicians, DJs, and entertainers and also perfectly suited for permanent installation in discos, pubs or public areas. The DAP Audio HP Series includes five power-amp models with outputs ranging from 200W to 1400W RMS stereo at 4 Ohms. The solid yet fashionable housings all hold forced air-cooling systems and the best protection circuits, ensuring many years of reliable amplification.
The HP-500 and HP-900 are ideal for pubs, bars, and parties. These class AB power amps deliver enough output to make everyone sing along and dance to their favorite tunes.
These amplifiers truly are the best choice wherever quality and reliability at affordable prices are required.
specifications
Output Power Stereo 2Ohm: Not Allowed Stereo 4Ohm: 2x 200 Watt RMS Stereo 8Ohm: 2x 150 Watt RMS Bridge 2Ohm: Not Allowed Bridge 4Ohm: Not Allowed Bridge 8Ohm: 1x400 Watt RMS Frequency Response: 10Hz - 20KHz, +/-1dB THD: 100dB A-weighted Crosstalk: >75dB Damping Factor: >100 8 OHM Gain: 32dB Input Sensitivity: 0,775V (+/-1dBv) Input Impedance: 20kOhm balanced, 10kOhm unbalanced Output Mode: Stereo / Parallel / Bridge Amp Technology: Class AB Protection: Clip Limiter (Fixed) Short Circuit Overheat Overload DC Voltage Cooling: Forced-air by axial fan Airflow: Front to side Input Connectors: 3-pin XLR Output Connectors: Speakon Power Connector: IEC Input Voltage: 210~240VAC, 50/60Hz Dimensions: 483 x 310 x 88mm Weight: 8Kg | L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.
Features |
---|
Fast response and low distortion | Easy to configure in stereo / mono / bridge modes | Extensive protective circuits ensure high reliability and operating safety | Front panel signal / clip / protect LED indicators | Minimum load impedance (stereo / mono): 4 Ohm | XLR input connectors | SPEAKON output connectors | Switchable limiter |
2 unit 19" rack, low weight for easy transportation
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 750 Watt rms | | Power output stereo 8Ω: | 2 x 450 Watt rms | | Power output bridged 8Ω: | 1500 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | 106 dB | | Damping factor: | > 300 | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | xlr | | Input sensitivity: | 1.4 V (/ 32 – 26 dB) dBm/V RMS | | Input impedance: | 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ | |
OUTPUT SECTION |
---|
Output connector: | Speakon | |
SYSTEM PARAMETERS |
---|
Cooling: | Forced | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220 ÷ 240 V (50 / 60 Hz) V ~ Hz | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88/3.4 mm/inch | | Width: | 482/18.9 mm/inch | | Depth: | 420/16.5 mm/inch | | Net Weight: | 17/37.4 Kg/Lbs |
|
|
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
- Rack mount stereo powered monitor speaker system
- New AES/EBU digital input
- lndependent MUTE function
- Sophisticated control panel section
- Ideal where space is at a premium
RM-2 is the ideal solution for monitoring needs in various space-challenged environments such as machine rooms, VTR monitoring, surveillance, mobile and stationary control rooms, theme park applications where audio monitoring is needed and the room for installation is not enough. Adding these new feature sets, RM-2 is now more versatile to various applications. - Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
- AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
- Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
- Independent MUTE function by holding down CH SEL key for a while.
- Auto Mute when powering on*.
- D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
- Multi-voltage power supply.
Speaker Section
- Unit: 110 x 40mm cone type, magnetically shielded, x 2
- Impedance: 8 ohms
- Output SPL: 84 dB/W (1m)
- Frequency response: 200Hz to 20kHz
Amplifier Section
- Rated output power: 10W or more (8 ohms, 1kHz)
- Residual noise: -60 dBV or less (DIN AUDIO)
- Distortion: 0.5% or less (10W / 4 ohms, 1kHz)
Digital input
- Connector: XLR-3-31 type
- Digital input Format: IEC60958 (AES/EBU)
- Digital inputSampling frequency: 44.1kHz to 96 kHz
Analog input
- Connector: XLR / 1/4" combi-jack
- Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
- Analog input Input impedance 10k ohms or more
Phones
- Connector: 1/4" stereo jack
- Applicable load imp. 8 ohms or more
- Rated output power 20mW + 20mW (32 ohms, 1kHz)
General
- External dimensions: 430(W) x 44(H) x 282(D) mm
- Weight: Approx. 3.5kg
- Power requirement: 100 - 240V~, 50/60Hz
- Power consumption: 10W
|
Reviews
There are no reviews yet.