DAP AUDIO D4176 HP-900 2x450W Amplifier

D4176_MANUAL_GB_V1.pdf

• Full protection circuits
• Efficient forced air cooling
• Stereo & Bridge mode

The DAP HP Series power amplifiers are the solution when true quality is needed in an affordable price range. The HP Series are 5 models representing output powers from stereo 200W until 1400W. All including the best protection circuits and built in a strong solid housing to achieve many years of reliable power. They are the best mobile choice  for musicians, DJs, and entertainers but also perfect for installations in discos, pubs or any kind of public areas.

The HP Series power amplifiers by DAP Audio are the obvious choice for musicians, DJs, and entertainers and also perfectly suited for permanent installation in discos, pubs or public areas.
The DAP Audio HP Series includes five power-amp models with outputs ranging from 200W to 1400W RMS stereo at 4 Ohms. The solid yet fashionable housings all hold forced air-cooling systems and the best protection circuits, ensuring many years of reliable amplification.

The HP-500 and HP-900 are ideal for pubs, bars, and parties. These class AB power amps deliver enough output to make everyone sing along and dance to their favorite tunes.

These amplifiers truly are the best choice wherever quality and reliability at affordable prices are required. 

Output Power
Stereo 2Ohm: Not Allowed
Stereo 4Ohm: 2x 450 Watt RMS
Stereo 8Ohm: 2x 350 Watt RMS
Bridge 2Ohm: Not Allowed
Bridge 4Ohm: Not Allowed
Bridge 8Ohm: 1x900 Watt RMS
Frequency Response: 10Hz - 20KHz, +/-1dB
THD: 100dB A-weighted
Crosstalk: >75dB
Damping Factor: >100 8 OHM
Gain: 32dB
Input Sensitivity: 0,85V (+/-1dBv)
Input Impedance: 20kOhm balanced, 10kOhm unbalanced
Output Mode: Stereo / Parallel / Bridge
Amp Technology: Class AB
Protection: Clip Limiter (Fixed)
Short Circuit
Overheat
Overload
DC Voltage
Cooling: Forced-air by axial fan
Airflow: Front to side
Input Connectors: 3-pin XLR
Output Connectors: Speakon
Power Connector: IEC
Input Voltage: 210~240VAC, 50/60Hz
Dimensions: 483 x 310 x 88mm
Weight: 10Kg

Reference Quality Power Amplifier [R-300 Plus]

• Controls :
  Front : Power on/off switch, attenuator, LED indicator
  Rear : Mode seletor switch, Stereo/bridged mono switch
• Connectors :
  Input : 1 XLR, 1/4" balanced per channel
  Output : 5-way binding post and SpeakonTM per channel
• Indicators :
  Power : Green, Protection : Red, Clip : Red, Signal : Green
• Power Source : 100-120VAC or 220-240VAC; 50/60Hz
  (supplied AC mains transformer depends on country requirements)
• Power Consumption : 250W(2.4A)
• Weight : 8.4kg/18.5lb
• Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in

These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.

Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)

InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz

high pass filter 30Ηz & 50Ηz

Solid DYNACORD technology for fixed installations at very competitive prices.
DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch.
The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.