Content |
Replacement stylus for Audio-Technica AT92ECD, AT301EP, AT311EP & AT316EP cartridges.
Stylus Shape: Elliptical Stylus Dimension: 0.3 x 0.7 mil To remove old stylus (needle), hold the cartridge in one hand, grasp the plastic stylus housing with thumb and forefinger, and pull away from the cartridge. To install replacement stylus, insert the new stylus assembly into the cartridge. The stylus assembly should click into place when fully seated on the cartridge. The stylus must be fully seated on the body for proper operation |
Technical data |
|
Frequency range |
20-29.000 Hz |
Frequency response |
20-20.000 Hz + 2 / -0 dB |
Tracking ability at 315Hz at recommended tracking force *) |
80 µm |
Compliance, dynamic, lateral |
22 µm/mN |
Stylus type |
Nude Fine Line |
Stylus tip radius |
r/R 8/40 µm |
Tracking force range |
1,4-1,7 g (14-17 mN) |
Tracking force, recommended |
1,5 g (15,0 mN) |
Tracking angle |
20° |
Stylus colour |
Bronze |
|
|
Recommended for following cartridges |
2M BRONZE |
| Ortofon 510MKII Stylus Technical Data
- Frequency range20-23.000 Hz
- Frequency response20-20.000 Hz + 2 / - 3 dB
- Tracking ability at 315Hz at recommended tracking force70 µm
- Compliance, dynamic, lateral25 µm/mN
- Stylus typeElliptical
- Stylus tip radiusr/R 8/18 µm
- Equivalent stylus tip mass0,3 mg
- Tracking force range1,25-1,75 g (12,5-17,5 mN)
- Tracking force, recommended1,5 g (15 mN)
- Tracking angle20°
- Stylus colourBlack
- Recommended for following cartridgesSeries 510 Mkll, 510, 510 P
|
| Replacement stylus for the Carl Cox Signature CS-1 Cartridge.
* Frequency response: 20 to 22,000Hz
* Output: 6mV
* Channel separation nominal: 32dB
* DC resistance: 430 ohms/ch
* Inductance: 400mH/ch
* Weight: 18.0g
* Channel balance: within 1.5dB
* Tracking force: 3–6g
* Recommended load: 47K ohms 200pf
* Stylus tip: fine circular diamond
* Application: club and mobile DJs, high output | DJ E Replacement stylus
Basic model for scratch and back-cueing. Outstanding rigidity by extra-strengthened cantilever
Features Special Elliptical stylus and a special developed and extremely balanced cantilever.
Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ.
The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.
DJ E Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-20.000 Hz +/-2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 9 μm/m N
Stylus type - Special Elliptical
Stylus tip radius - r/R 13/25 μm
Tracking force range - 2,0-4,0 g (20-40 mN)
Tracking force recommended - 3,0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 18,5 g
Compatible with cartridges - DJ S | Stylus 5E
Technical data |
|
Frequency range |
20-25.000 Hz |
Frequency response |
20-25.000 Hz |
Tracking ability at 315Hz at recommended tracking force *) |
|
|
Reviews
There are no reviews yet.