| Content |
A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.
- Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
- External contact closure capability permits control of remote devices from microphone switch
- External LED control allows for accurate depiction of the live status of the microphone
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 266g
- Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
- Output Connector: TB5M-type
- Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device
|
C 562 CM
Small, low-profile boundary layer microphone
Wide frequency range
High sensitivity
Ideal for inconspicuous installation in a room
Suited for surveillance or recording
The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL.
The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings,
walls, tables, stage props, etc.
Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording
since a single microphone can cover an entire room. The supplied XLR phantom power adapter
connects to the microphone cable through a miniature connector so installation holes can be
smaller than the diameter of the phantom power adapter.
SPECIFICATIONS:
Polar pattern omnidirectional (hemispherical)
Frequency range 20 to 20,000 Hz
Sensitivity 25 mV/Pa (-32 dBV)
Max. SPL 130 dB (k=1 %)
Equivalent noise level 16 dB-A
Signal/noise ratio (A-weighted) 78 dB
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN/IEC
Current consumption Connector 3-pin XLR
Cable 0.5 m (20 in.)
Finish matte nickel plated
Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.)
Net weight 30 g (1.1 oz.)
Shipping weight 195 g (76.9 oz.)
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
Available Options
MX396C/DUAL Dual-Element 0-180 Degrees, Cardioid, back or bottom exit cable, mute output, LED input
MX396/TRI Dual-Element 90-0-90 mic, adjustable to 120-120-120 degrees, Cardioid, back or bottom exit cable, mute output, LED input
The Microflex® Multi-Element Boundary microphone delivers a unique and versatile tool for conference room installations.
Clean and simple in appearance, Multi-Element Boundary mics come in two or three element configurations, combining the coverage of multiple microphones into one small, compact package.
|
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
The new Engineered Sound.
This low-profile omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording and teleconferencing in table-, ceiling-, or panel-mount applications. The microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. The microphone offers unsurpassed immunity from radio frequency interference thanks to Audio-Technica's UniGuard® innovations. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a 360º pickup angle, and is available in two colors: black (ES945) and white (ES945W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform omnidirectional polar pattern with 360º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES945) and white (ES945W)
- RoHS compliant-free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Omnidirectional
- Frequency Response: 40-18,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 112 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 63 g (2.2 oz)
- Dimensions: 69.0 mm (2.72“) long, 28.0 mm (1.10“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
The U841A delivers exceptionally intelligible audio reproduction in a super-compact, low-profile design. Equipped with UniGuard® RFI-shielding technology, this omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording, television and conferencing in surface-mount applications. The U841A has a 360° pickup angle and operates on battery or phantom power.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and silicon foam bottom pad minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate permanently polarized condenser
- Polar Pattern: Omnidirectional in hemisphere above mounting surface
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -39 dB (11.2 mV) re 1V at 1 Pa Battery: -40 dB (10.0 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 132 dB, 1 kHz at 1% T.H.D. Battery: 122 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB, 1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 73 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
Reviews
There are no reviews yet.