| Content | The xCAN simply makes your music sound better, whether you are listening via ear buds at home or chilling with tunes on the go.
The mother of all amplifiers
The xCAN is a portable amplifier above all else and is for anyone who enjoys good sound.
Using a high-end DAP that has an adequate onboard DAC but lacks power? Happy with your existing source but need more juice?
Just add the xCAN to drive bigger and better headphones and boost your tunes.
Blinding Bluetooth
The xCAN delivers CD-Quality Bluetooth via AAC, aptX and aptX LL with added iFi magic.
Stream wirelessly from your smartphone. Bluetooth from your TV to the xCAN. No need for wires. Just plug your headphones into the xCAN at your side.
Give soundtracks extra energy. Add oomph to your gaming! Hear the whoosh of an arrow or the full throttle of F1 car in all their glory.
Wicked wiring
Connect via a digital SPDIF or via analogue 2.5/3.5 connection. iFi’s exclusive S-Balanced technology means that you gain the advantages of a balanced connection even when using an unbalanced one.
On headphones this means lower distortion, less interference and less crosstalk.
And it enables you to take advantage of the growing number of balanced sources, such as high-end DAPs.
A pure power house
The xCAN is a dual-mono headphone amplifier with 1000mW of power per channel. It will happily drive your favourite headphones.
And we added our signature sonic extras as well.
3D+® opens up your music to give you the spaciousness of a live-concert atmosphere.
The XBass Ⅱ® analogue bass correction system corrects headphone/speaker bass response to deliver a more natural sound to the midrange frequencies.
Clever. Curvy.
The xCAN smart battery provides up to 18 hours of playback time (analogue) or 12 hours (Bluetooth) depending on your choice of headphones. That’s one very long train journey!
And finally, check out the curvy chassis and lush LEDs. The xCAN is one lovely lady.
Specifications
| Inputs |
Wireless |
ESS Sabre 44.1/48k 16-Bit (AAC, aptX, aptX LL and SBC) |
| Wired |
3.5mm (TRS or TRRS S-Balanced*) and 2.5mm (TRRS)
*ONLY found in iFi components such as nDSD BL. Do NOT feed using normal TRRS Balanced output sources.
No USB audio input |
| Max Output |
S-Balanced |
> 3.8V / 45 mW (@ 300 Ohm)> 3.5V / 380 mW (@ 32 Ohm)> 3.1V / 600 mW (@ 16 Ohm |
|
Balanced |
> 7.6V / 90 mW (@ 600 Ohm)> 7.2V / 800 mW (@ 64 Ohm)> 5.7V / 1,000 mW (@ 32 Ohm) |
| THD & N |
S-Balanced |
< 0.005% (@ 100 mW/1.26V 16 Ohm) |
| Balanced |
< 0.006% (@ 360 mW/2.4V 16 Ohm) |
| SNR |
S-Balanced |
> 121dBA (@ 3.8V) |
| Balanced |
>120dBA (@ 7.6V) |
| Recommended HP Impedance |
16~600 Ohm |
| Output impedance |
S-Balanced |
|
|
Plug In, Rock Out with the Joe Satriani amPlug headphone amp
The Joe Satriani signature model is the latest addition to our incredibly popular amPlug series of headphone guitar amps!
- Joe's signature lead tone with your choice of delay on or off
- Distortion tone with superb dynamic response, inspired by the Satchurator
- Analog-style delay with Joe's filter & EQ, inherited from the Time Machine
- Plugs straight into your electric guitar, so you can instantly enjoy great sound through your headphones
- Convenient and portable with up to 11 hours of battery operation
- AUX input jack lets you jam along to tunes on your CD/MP3 player
The amPlug series of palm-sized headphone guitar amps make it easy to enjoy great guitar/bass sounds at home, in your room, or anywhere. This lineup is now joined by the amPlug Joe Satriani signature model, which borrows freely from the VOX/Joe Satriani line of signature pedal effects.
Specifications -
Power supply: AAA batteries (x 2)
-
Battery life (FX on):
Zinc-carbon batteries: approximately 3 hours
Alkaline batteries: approximately 11 hours
-
Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22"
-
Weight: 40 g/1.41 oz. (not including batteries)
-
Included items: Two AAA batteries (for verifying operation)
|
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
|
INPUT: 1 audio stereo, 1Vpp/50kΩ on a 6.5mm stereo phone socket.
OUTPUTS: 5 audio stereo, 500mW/8Ω on 6.5mm stereo phone sockets.
AUDIO BANDWIDTH (-3dB): 25kHz.
CONTROL: 5 stereo output level controls (front), 1 mono switch (rear).
GAIN RANGE: -60dB to +10dB.
S/N RATIO: 78dB.
THD: 0.08% @100mW.
POWER SOURCE: 12V DC, 370mA nom, 1A max.
DIMENSIONS: 16.5cm x 12cm x 4.5cm (6.5” x 4.72” x 1.77”) W, D, H.
WEIGHT: 0.68kg (1.5lbs) approx.
ACCESSORIES: 12V DC power supply.
OPTIONS: RK-1 19" rack adapter.
|
The compact HX-3 Headphone Distribution Amplifier is the perfect accessory to quickly provide three high-performance stereo headphone feeds with individual level controls from line-level sources. The HX-3 can produce very high headphone levels with extremely low noise and distortion.
HX-3 Key Features
Great for radio, television, film, and music production applications, the battery-powered HX-3 accepts balanced XLR line-level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs. Its 1/4-inch loop-out can connect multiple HX-3's for additional headphone outputs. Headphones are connected to panel-mounted 1/4-inch stereo connectors.
The HX-3 has a durable aluminum chassis to withstand the punishment of field and studio environments. The unit is powered by inexpensive batteries (two-AA) or external 5-18 VDC.
The HX-3 can add headphone outputs to the 552, 302, MixPre-D, MM-1, and USBPre-2.
HX-3 Key Features List - Three isolated headphone outputs with individual volume controls.
- 125 dB dynamic range with flat frequency response.
- Durable 1/4-inch connectors, panel mounted for strength.
- Stereo or mono monitoring.
- Peak LED indicates headphone overload.
- Two balanced XLR line level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs.
- Loop Output to connect additional HX-3's in series.
- All-metal connectors solidly mounted to the chassis for durability and RF immunity.
- Free from "Pin-1" grounding problems.
- Internal battery-power for up to 18 hours from two AA alkaline batteries.
- Chassis-isolated 5 to 18 VDC input for easy external DC powering.
- Power LED indicates low battery power.
- High strength, extruded aluminum chassis with protective metal end panels.
| LD Sytems HPA 4 - a compact and powerful headphone amplifier
The LDHPA4 has small dimensions, can handle up to 4 headphones and has an output power with no equal in its class. That means high volume with no distortion. With these features the LDHPA4 is an essential tool for every project- and home studio.
Specifications
Product type
Headphone Amp:
Inputs
2
Input connectors
6.3 mm TRS , RCA
Input impedance
1 k Ohm(s)
Outputs
2
Output connectors
6.3 mm Jack
Power output
4 x 100 mW
Minimum connected impedance
10 Ohm(s)
Frequency response
20 - 20.000 Hz
Controls
4 x headphone volume , Mono/stereo switch
Indicators
Power
Operating voltage
External Power Supply
Operating voltage
24 V DC
Cabinet material
metal
Cabinet surface
painted
Width
94 mm
Height
48 mm
Depth
82 mm
Weight
0,27 kg
Accessories (included)
power supply |
Reviews
There are no reviews yet.