Axel Technology Boxtel MKII Basic Telephone Hybrid

• Compact telephone hybrid
• 1 POTS/PSTN or GSM DualBand telephone line
• Send/Receive audio levels control and visualization
• Backlit Hook/Ring button
• Software configuration
• Phone call auto-answer feature
• International selection of the line impedance
• Remote control
• Potentiometer levels and front panel control
• Analogue Send/Receive balanced over XLR
• 1 USB port
• GPIO to remotely control Telco N-1 modules

• Dimension LxHxD 22x5x13cm
• AC Rate 230Vac / 110Vac 50 Hz / 60 Hz 30VA
• Type of power supply Switching power supply, worldwide
• Weight ≈ 2500 gr
• Operating Temperature -5°C / +50°CANALOG INPUT MODULE (send)
• Connectors: XLR, female - Electronically balanced
• Operative Nominal Level: 0 dBu
• Line Impedance 10 kΩ (Electronically balanced selectable) EMIsuppressed
• Distortion: less than 0.01% TDH+NOISE (0.0dBu 1Khz)
• Input Modes: MonoANALOG OUTPUT MODULE (receive)
• Connectors XLR, male - Electronically balanced
• Output Level 0dBu +4dBu +6dBu Max +20dBu
• Load Impendance 600 Ω
• Distorsion Less than 0.01% TDH+NOISE (0.0dBu @ 1Khz)
• Output Modes: MonoTELEPHONE MODULE PSTN / POTS
• Connectors LINE RJ 11C 6/4 socket
• Connectors SET RJ 11C 6/4 socket
• Bandwidth telephone line 100Hz 5kHz, -3dB @ 1 kHz
• Telephone line compliance ETSI TBR21, FCC Part68
• Isolation 3 kVREMOTE INTERFACE
• Digital Inputs GP In 2x GP In opto coupled. Only 1 is used as Hook
• Digital Outputs GP Out 2x GP Out Open Collector opto isolated. Only GPOut 1 is used as RingTechnical Specification about BoxTel MKII GSM (Additional )
• TELEPHONE MODULE GSM Module
• Standard DualBand GSM 900/1800 Mhz Phase 2+
• Frequency GSM 900: (Tx) 890 915 Mhz / (Rx) 935 960 Mhz
• GSM 1800: (Tx) 1710 1785 Mhz / (Rx) 1805 1880 Mhz
• Sensitivity -104 dB
• Channel bandwidth 200 kHz
• Maximum consumption 0.25 W / 0.5W
• Stand-by consumption
• Sensitivity -104 dB
• Dial tone frequency 450 Mhz Standard
• Environment noise
• Transmitting Power
• External Antenna 2.5 dBi omnidirectional with 1mt standard cable
• External power supply unit Input: 100-240 Vac Output: 12 V 500 mA
• External Antenna connector SMA
• Total rechargeable battery time 6 h
• PSTN / POTS connector RJ 11C 6/4 socket
• Operating temperature 0°C ≈ +45°C
• EN COMPLIANCY for GSM Modul EN 60950-1
• EN 301 489-1/-7
• EN 301 511

Innovation

The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
 
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
 
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
 
T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.
 

In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.

The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.

All four channels have the following controls:

Threshold - allows you to set the level at which the compressor starts affecting the gain

OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.

Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.

Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.

Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.

Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.

PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.

Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.

All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.

• Four independent channels of operation, stereo linkable in two pairs
• PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
• Independent Threshold and ratio controls
• Switchable OverEasy® or Hard Knee compression
• Classic dbx® compression
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Precision metering of input level, output level, and gain reduction
• Dual True stereo or quad mono operation
• Switchable +4dBu or -10dBV operation per channel

• Error proof operation to smooth uneven levels, add sustain to guitars, fatten drums or tighten up mixes
• New gate timing algorithms ensure the smoothest release characteristics
• Program-adaptive expander/gates
• Great sounding dynamics control for any type of program material
• Separate precision LED displays for gain reduction, compression threshold and gate threshold allow quick, accurate setup
• Stereo or dual-mono operation
• Balanced inputs and outputs on 1/4" TRS and XLR connectors
• Side Chain insert
• Classic dbx® "Auto" mode

VIRTUALIZER 3D FX2000
High-Performance 3D Multi-Engine Effects Processor
71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
Awesome modulation, dynamic, psychoacoustic and EQ algorithms
Authentic amp simulation, distortion and special effects
11 effect combinations with selectable serial / parallel configuration
Up to 7 adjustable parameters plus 2-band EQ per effect
24-bit A/D and D/A converters with 64/128-times oversampling
True stereo processing for realistic channel separation in stereo image
100 factory presets plus 100 user memory locations
Extensive MIDI implementation
Accurate LED level meters for perfect level setting and optimum performance
Servo-balanced XLR and ¼'' TRS inputs and outputs
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

 Reverbs & Delays

Because it is one of the most desired effects, the FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.

Reverbs include:

    CATHEDRAL
    GOLD PLATE
    SMALL HALL
    ROOM
    STUDIO
    CONCERT
    STUDIO
    STAGE
    SPRING REVERB
    AMBIENCE
    EARLY REFLECTIONS

Specialty reverbs include:

    REVERB – reverb is synthetically turned off after a predetermined amount of time
    REVERSE REVERB – reverb envelope is reversed—it slowly gets louder

Delays include:

    STEREO DELAY – delay is processed across the entire stereo image
    TAPE ECHO – simulates classic tape echo devices, pre-dating the advent of digital delays
    PING PONG – delay signal is "bounced” from left to right at an adjustable tempo

Much More than Just Reverb and Delay

The FX2000 has some of the best-sounding reverb and delay programs, but thatʼs not all. It also provides excellent modulation effects (such as chorus, flanger and phaser), including special variations like musical pitch shifter, tremolo and even a rotary speaker simulation.

Modulation and Pitch Shifter FX:

    STEREO FLANGER (originally generated by playing back two synchronized "reel to reel” tape recorders with a finger rubbing on the flange of one of the take-up reels)
    VINTAGE FLANGER simulates a guitar fl anger stomp box
    JET STREAM FLANGER sounds like a classic analog flanger
    STEREO CHORUS (combines a slightly detuned signal with the original)
    ANALOG CHORUS simulates a guitar chorus stomp box
    VINTAGE CHORUS imitates a classic analog studio chorus
    ULTRA CHORUS creates the sound of an eight person chorus
    STEREO PHASER (combines a second, phaseshifted signal to the original)
    VINTAGE PHASER represents a guitar phaser stomp box
    DUAL PHASER processes the left and right channels separately
    ROTARY (simulation of the rotating speakers typically used on an organ) – Slow or Fast
    PITCH SHIFTER (changes the pitch of the original signal) – can be used to create harmonies with the original signal or replace it entirely with the altered pitch. Choices include stereo, two and three vocal pitch shifter
    VIBRATO – the peak frequency of the tone is periodically and uniformly changed (quickly or slowly)
    TREMOLO (common vintage guitar amplifier effect) – a fast or slow periodic variation in volume
    AUTO PANNING – signal is automatically sent from one side of the stereo image to the other, either once or multiple times

Dynamic FX:

    COMPRESSOR – reduces the dynamic range of the signal, maintains consistent signal level and thus avoids distortion associated with excessive input levels
    EXPANDER – effectively broadens the dynamic range of source signals while reducing background noise
    GATED REVERB – helps reduce background clutter by turning reverb off below a predetermined threshold level. Particularly effective on drum mics and vocals
    ANA. KOMPR/LIM. — similar to COMPRESSOR but with Limiting functionality
    ULTRAMIZER – analyses incoming signal and automatically applies compression across two independent frequency bands
    DENOISER – eliminates or reduces noise and other interference
    DE-ESSER – reduces or removes sibilance (Ssss sound) from signal
    WAVE DESIGNER – allows you to influence the envelope by adjusting Attack and Release of the signal

Psychoacoustic FX:

    EXCITER – adds artificially generated overtones to the original signal, increasing presence and perceived loudness without significant increase in signal level
    ENHANCER – functions much like a dynamic pitch equalizer
    ULTRA BASS – sub-harmonic processor combined with bass exciter and limiter
    STEREO IMAGER – divides the signal into middle and side signals, allowing individual signals to be amplif ed when desired and placed on the stereo image
    ULTRA WIDE – creates a broader stereo image
    BINAURALIZER – also creates a broader stereo image and compensates for crosstalk between both speakers

Filter/EQ FX:

    AUTO FILTER – influences the frequency response of a signal. Two filters are included: low pass allows low frequencies to pass and suppresses high frequency content; high pass does the exact opposite
    LFO FILTER - Controls the rate of oscillation effects
    PARAMETRIC EQ – allows you to control the bandwidth, frequency and amplitude of a signal
    GRAPHIC EQ – the sound spectrum is divided into eight (8) adjacent frequency bands, which can be cut or boosted, bandwidth is predetermined

Distortion FX and Amp Simulations

The FX2000 is also equipped with distortion, amplifier and speaker simulation including VOCAL DISTORTION, TUBE DISTORTION, GUITAR AMP, TRI FUZZ, SPEAKER SIMULATION, RING MODULATOR and LO-FI.

Special FX:

    VINYLIZER – adds clicks and/or noise to the signal, reminiscent of old vinyl records and tape machines
    SAMPLER – allows you to record and playback up to five (5) seconds of program material
    VOCODER – allows the input signal to modulate another signal (usually a synthesizer sound), creating the familiar "talking synthesizer” effect
    VOICE CANCELER – removes mono vocal parts from stereo recordings for "instant Karaoke”
    RESONATOR – simulates and oscillating system that amplifies a specific frequency

Our FX Combinations Go to 11

Sometimes you want to add a little (or a lot) of color to your reverb and delay patches. The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.

FX Combinations include:

    Chorus & Reverb
    Flanger & Reverb
    Leslie & Reverb
    Pitch & Reverb
    Delay & Reverb
    Tremolo & Reverb
    Phaser & Reverb
    Chorus & Delay
    Flanger & Delay
    Pitch & Delay
    Tremolo & Delay

Enhanced User Editability
Logical grouping of parameters, along with the combination of encoders, buttons, LEDs and an easily readable LED display, make operating the FX2000 a breeze. You are free to edit up to seven parameters per preset, and then save them for future use in the 100 provided memory locations.
Value
With its extremely powerful processing capability and versatile array of features, the FX2000 will become the busiest tool in your audio arsenal. Stop by your BEHRINGER dealer today and find out why more professional sound engineers are turning to the FX2000 as their primary FX processor— both in the studio and on the road.