| Content |
- 2Χ350W 8Ω 2x500W 4Ω 2x650W STEREO MODE
- BRIDGE 2000W 4 Ω
- 16Kg
- 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
- Precise Power, Signal and Clip LEDs to monitor performance
- XLR and 1/4" TRS input connectors for compatibility with any source
- Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
- Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
- Independent limiters per channel offer reliable protection against overload and distortion
- High-current toroidal transformer for ultra-high transient response and absolute reliability
- Ultra-reliable Toshiba/Fairchild power transistors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front” ventilation system including air filter for reliable operation
- “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 800: 2x 400 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight: 13 kg/(29 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
| The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Frequency response
20 - 20000 Hz
Signal-to-noise ratio
105 dB
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Features
Volex mains socket
|
The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series
power amps combine excellent audio performance, modern and innovative
circuit design, meticulous and exceptionally rigid construction, and the highest
levels of operational integrity and reliability with an appropriate and more than
realistic price. The robust steel chassis provides outstanding torsional strength
through L-shaped side panels reaching under the thick aluminium front panel.
Thermal breakers prevent the power supply units from being damaged by thermal
overload. Electronically controlled fans provide sufficient front-to-rear airflow and
a special cool air diverter takes care of thermal stability. The fans? noise-level is
extremely low which provides the possibility for studio use. If necessary, a supplied
air-filter can be mounted behind the front panel ventilation louvres.
Features
* Excellent audio performance
* Symmetrical topology
* Ultra-low distortion
* Generously dimensioned power supply units
* Suitable to be operated on loads down to 2 ohms
* Suitable to drive complex loads with phase angles of ± 90 degree
* Extensive protection circuitry
* Unique Back-EMF protection
* Switchable limiters
* Switchable Hi/Lo-Cut filters
* Robust steel chassis
* Exceptional low noise front-to-rear air-flow
* XLR-type inputs and direct-outs
* LED display shows On, In, Out, Limit and Protect
* Highly reliable operation
Specs
* Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0%
* Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 %
* Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz
* Phase Angle Response : ± 30 degree/20 Hz.....20 kHz
* Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1%
* Voltage Gain ref. 1 kHz : 26 dB (constant gain option)
* Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz
* Maximum Input Level : +21 dBu / 8.7 V
* Input Impedance active balanced : 20 kohms
* THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz
* IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output
* Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms,
A-weighted, RMS, input sensitivity +6 dBu
* Attenuation at rated output : > 70 dB f = 1 kHz
* Damping Factor internal 1 kHz : > 300
* DIM 30 : < 0.01 %
* DIM 100 : < 0.01 %
* Slew Rate internal : > 25 V / ?s
* Power Consumption : 300 W 1/8 rated output into 4 ohms
* Width : 483 mm
* Height : 88.1 mm
* Depth : 426 mm
* Weight : 14 kg
|
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)
|
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty
TECHNICAL DATA:
Basic 200: 2x 100 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: > 400 @ 4 Ohm
Cooling: 2x Fan (temp. reg. variable speed)
Weight: 10 kg.
Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“) |
Reviews
There are no reviews yet.