1968 MkII – Dual Channel Tube Compressor Blend valves and FETs for quality compression. The 1968 MkII is a 1U Tube/FET ‘stereo bus’ compressor which by design delivers a transparent ‘open’ sound even during periods of heavy compression. The original Drawmer 1960 used a tube stage at the front of the compressor, whilst the 1968 MkII utilisies […]
Blend valves and FETs for quality compression. The 1968 MkII is a 1U Tube/FET ‘stereo bus’ compressor which by design delivers a transparent ‘open’ sound even during periods of heavy compression.
The original Drawmer 1960 used a tube stage at the front of the compressor, whilst the 1968 MkII utilisies a J-FET (Field Effect Transistor) gain reduction circuit that operates faster than an opto-isolator. The compressor uses a 12AX7 tube makeup gain amplifier where you can add, with the Output Gain control, up to 20 dB of additional gain. The need for a ratio control has been removed as the compressor operates on the soft knee principle where the onset of compression is progressive.
The 1968 MkII expands attack times to six choices: 2, 9, 15, 25, 30 and 50 ms. Release times come in three fixed times (100ms, 500 ms and 1 second) and three program-dependent choices–200 ms to 2 sec, 500 ms to 5 sec and 1 to 10 seconds–all program-dependent and automatic.
The 1968 MkII provides full sidechain access for connecting an external equalizer for vocal stressing or de-essing.
Featured on both channels is a switchable ‘BIG’ and ‘BIGGER’ mode which applies less processing to the fundamental low frequency but still disciplines the upward associated harmonics which if untamed can result in a ‘boomy’ or ‘boxy’ sound. The result – a solid bottom end with enhanced sub-bass and a smoother, wider frequency response overall. This lets the operator use more compression on an overall mix with less pumping action caused by a kick and/or bass instrument.
The outputs of Channels 1 and 2 are monitored on two yellow illuminated VU meters – with a red warning glow to signify ‘approaching clipping’. A three-position switch adjusts the meters to show either normal output level, gain reduction or VU +10dB mode, which re-scales the meter for users working at ‘hot’ output levels.
An output switch selects normal compressor output, hard-wired bypass and sidechain listen.
The key features are as follows:
2 Channel Tube/FET Compressor.
2 soft-knee compressors with variable threshold, attack, release and output gain.
Switchable BIG and BIGGER control on each channel.
Dual mono or true stereo link operation.
Side chain access and side chain listen facility.
VU metering of gain reduction and output levels.
Switchable +10dB mode on VU re-scales the meter for users working at ‘hot’ output levels.
VU red warning glow to signify ‘approaching clipping’.
Balanced +4dB XLR in/outs.
Due to customer demand we have introduced new features to the 1968 MkII:
Expanded the BIG to include BIGGER – setting the filters to 75Hz and 150Hz.
Added internal jumpers that can be configured to remove the soft clip section.
Added internal jumpers to make the output hotter by 6dB, if required.
Improvement have been made to the PSU to lower the noise floor.
Weight
3.00 kg
Reviews
There are no reviews yet.
Be the first to review “DRAWMER 1968 MKII Dual Channel Tube Compressor” Cancel reply
Blend valves and FETs for quality compression. The 1968 MkII is a 1U Tube/FET ‘stereo bus’ compressor which by design delivers a transparent ‘open’ sound even during periods of heavy compression.
The original Drawmer 1960 used a tube stage at the front of the compressor, whilst the 1968 MkII utilisies a J-FET (Field Effect Transistor) gain reduction circuit that operates faster than an opto-isolator. The compressor uses a 12AX7 tube makeup gain amplifier where you can add, with the Output Gain control, up to 20 dB of additional gain. The need for a ratio control has been removed as the compressor operates on the soft knee principle where the onset of compression is progressive.
The 1968 MkII expands attack times to six choices: 2, 9, 15, 25, 30 and 50 ms. Release times come in three fixed times (100ms, 500 ms and 1 second) and three program-dependent choices--200 ms to 2 sec, 500 ms to 5 sec and 1 to 10 seconds--all program-dependent and automatic.
The 1968 MkII provides full sidechain access for connecting an external equalizer for vocal stressing or de-essing.
Featured on both channels is a switchable ‘BIG’ and ‘BIGGER’ mode which applies less processing to the fundamental low frequency but still disciplines the upward associated harmonics which if untamed can result in a ‘boomy’ or ‘boxy’ sound. The result - a solid bottom end with enhanced sub-bass and a smoother, wider frequency response overall. This lets the operator use more compression on an overall mix with less pumping action caused by a kick and/or bass instrument.
The outputs of Channels 1 and 2 are monitored on two yellow illuminated VU meters - with a red warning glow to signify ‘approaching clipping’. A three-position switch adjusts the meters to show either normal output level, gain reduction or VU +10dB mode, which re-scales the meter for users working at ‘hot’ output levels.
An output switch selects normal compressor output, hard-wired bypass and sidechain listen.
The key features are as follows:
2 Channel Tube/FET Compressor.
2 soft-knee compressors with variable threshold, attack, release and output gain.
Switchable BIG and BIGGER control on each channel.
Dual mono or true stereo link operation.
Side chain access and side chain listen facility.
VU metering of gain reduction and output levels.
Switchable +10dB mode on VU re-scales the meter for users working at ‘hot’ output levels.
VU red warning glow to signify ‘approaching clipping’.
Balanced +4dB XLR in/outs.
Due to customer demand we have introduced new features to the 1968 MkII:
Expanded the BIG to include BIGGER - setting the filters to 75Hz and 150Hz.
Added internal jumpers that can be configured to remove the soft clip section.
Added internal jumpers to make the output hotter by 6dB, if required.
Improvement have been made to the PSU to lower the noise floor.
Innovation
The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter designed for use in any professional audio dynamics control application. Multiple Modes The Afterburner can be set up and used in three different ways: In Two channel mode, it performs as two independent compressor/limiters, with 'industry standard' variable Threshold, Ratio and Output gain. In stereo mode, our New Adaptive Stereo Link circuitry provides increased stereo imaging accuracy when linking both channels as a stereo pair. A single front panel switch puts the Afterburner into its alternative Mono mode, setting it up as a Single channel, Dual Band compressor/limiter, with separate dynamics control of both Low and High frequencies, opening up a whole new range of gain control techniques. Enhance Switch In any mode, the Afterburner features an 'Enhance' switch, which provides frequency restoration to preserve the spectral balance of the audio signal, compensating for the sagging Low and High frequency response of compressed program material. Think of it as a 'smart' loudness control.
Features Switchable Modes - Stereo; Dual Channel Single band; or Single Channel Dual Band (Low and High) Low and High frequency compression in Single Channel mode 'Enhance' switch restores spectral balance of compressed signal New Hard/Soft knee compression switch New Adaptive Stereo Link circuit for accurate stereo imaging New Above/Below Threshold LEDs enable at-a-glance compression confirmation Balanced XLR and Jack Inputs and Outputs Sidechain Insert points Intuitive user-friendly layout Flawless performance
New Above/Below Threshold LEDs enable at-a-glance compression confirmation New Hard or Soft knee compression option New LED metering provides accurate Level status, with separate Gain Reduction metering in easy to read 'wide scale' meters. There is also comprehensive LED indication of all operating functions and status in any mode. Balanced Inputs and Outputs On the rear panel, each channel has true differential Balanced inputs and outputs, on both XLR and TRS jack connectors. As well, each channel has a TRS jack Sidechain access insert point, for applications such as De-essing (when used with an external equalizer such as the ARX Multi Q or EQ 260).Other features include a true Hardwire bypass switch for each channel, and passive RFI filters on the inputs. Universal AC Power AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to the unit via a removable power lead and standard 3 pin IEC connector, with built-in fuse and voltage change switch. With its smooth compression, intuitive user friendly layout, high density precision circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner is equally at home in Studio, Installation, Broadcast and Sound Reinforcement environments. It can provide great sounding dynamics control effects that are not available with any other device.
T E C H N I C A L S P E C I F I C A T I O N S Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms Input Headroom + 22 dB CMRR >60 dB, 20 Hz-20 KHz Output Impedance Balanced 300 ohms, Unbalanced 150 ohms Output Level (Max) + 22 dB Frequency Response 20Hz to 20KHz ±0.2dB Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted Distortion .02% THD @ 0dB,1KHz Dynamic Range 115 dB Sidechain Insert Impedance 10 Kohm Filter Section Filter Type Phase corrected 6dB/octave Summed Filter Response ±0.2dB through crossover region Dividing Frequency 250 Hz Enhance Section Low Enhance 50 Hz, High Enhance 10 KHz Power Requirements 100/120 V AC, 220/240 V AC Weight 5 lbs/2.2 Kg Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm Input/OutputConnector type XLR, Balanced Jack Sidechain Insert Connector TRS Jack
Front Panel Controls Hardwire bypass IN/OUT switch Threshold, Ratio and Output Gain controls Above/Below Threshold LEDs 12 segment LED Output Level display Numbered marker panel for labelling compressor assigns 7 segment LED Gain Reduction display Enhance switch and status LED Adaptive Stereo link switch and status LED Dual/Single channel mode switch and status LEDs Rear Panel Connectors Balanced Inputs and Outputs, on both XLR and TRS jack connectors. In Single channel (Mono) mode, use Channel 1 Inputs and Outputs only Sidechain Insert TRS connector on each channel AC input connector, with voltage switch and fuse.
OPTIMOD-FM 5500 puts coveted five-band and two-band OPTIMOD processing into a single rack unit package and brings it to you at the most affordable price ever.
Quality sound is what 5500 is all about-sound that attracts audiences by providing a polished, professional presentation regardless of format and source material. Exceptional versatility allows you to adjust the processor's audio texture to brand your audio, knowing that the resulting signature sound will remain consistent, cut-to-cut and source-to-source. Branding builds businesses and no other processors have the consistency to brand your sound like OPTIMOD.
With the 5500, your signature sound is just a preset away. An easy, one-knob Less/More adjustment allows you to customize any factory preset, trading cleanliness against processing artifacts according to the requirements of your market and competitive environment. Full Control gives you the versatility to customize your audio further. And, if you're a hard-core processing expert, you can explore Advanced Control to tweak presets at the same level as Orban's factory programmers. This versatility makes the 5500 a superb choice for any format. Its five-band processing is ideal for any pop music format (even the most competitive and aggressive CHR), while phase-linear two-band processing yields ultratransparent sound for classical, classic jazz, and fine arts formats. Regardless of your choice, 5500's optimized technology ensures unusually high average modulation and coverage for a given level of subjective quality. Unlike many lesser processors, the 5500 handles speech particularly well. It's always clean, even when you process for loudness.
If you're concerned about latency because you need to feed live talent headphones off air, be assured that the 5500's ultra-low-latency (5 ms delay) processing will keep the most finicky talent happy. Or use optimum latency (15 ms delay) processing for the most competitive sound with delay that's still low enough to satisfy most any talent.
Versatility doesn't stop with sound.
The 5500 can also be used as a superb stand-alone stereo encoder with latency as low as 2 ms and full overshoot limiting in both the left/right and composite baseband domains.
When used in this mode, the 5500 must be driven (usually via an STL) by a full-featured FM audio processor (like Orban's 8600) that incorporates pre-emphasis aware HF limiting and peak control. In both modes, the 5500's stereo encoder helps deliver a transmitted signal that's always immaculately clean and perfectly peak limited, with full spectral protection of subcarriers and RDS/RBDS regardless of the amount of composite limiting.
It is the ideal choice for network broadcasters who process with Orban's flagship OPTIMOD-FM 8600 at the network origination point and who need a processor at every transmitter to eliminate STL overshoots (using the 5500's stand-alone stereo encoder mode) and/or to process local insertions while also eliminating network STL overshoots (using the 5500's audio processor / stereo encoder mode). Moreover, the 5500's two modes make it easy for large government and network broadcasters to manage its inventory of spares because any 5500 can be used as a stereo encoder with or without audio processing.
Available in both modes, the built-in, defeat-able ITU-BS412 multiplex power controller allows the 5500's output to meet even the most stringent European government regulations.
A 10 MHz frequency reference input allows the stereo pilot tone frequency to be locked to GPS or another high-accuracy frequency standard. This improves the performance of single-frequency networks in areas where coverage of the transmitters overlaps.
The 5500's built-in stereo encoder, AES/EBU digital inputs and outputs, and analog I/O permit hasslefree interfacing to any broadcast plant, whether the 5500 is located at the studio or the transmitter. Tight band limiting to 15 kHz means you can use any uncompressed digital STL to pass 5500- processed audio from studio to transmitter without compromising on-air loudness - there's no need to use STL's having 44.1 or 48 kHz sample-rate.
The stereo encoder's stereo sub-channel modulator can operate in normal double sideband mode and in an experimental compatible single sideband mode (SSB/VSB) that is offered to enable users to compare and assess the two modes.
Analog Fallback to Digital control that allows Silence Sense to switch the active input from Analog to Digital if silence is detected in the analog input signal but not on the digital input signal. This function works vice versa as well on both analog and digital AES input. The silence sense parameters apply to both simultaneously and both detectors are available to drive the 5500's tally outputs and sending SNMP Traps/Alerts.
If you want to locate the 5500 away from the studio, you'll be pleased by its three separate remote control ports - GPI contact closures, RS232 serial and built-in Ethernet for TCP/IP networks. The serial and Ethernet ports are supported by the supplied 5500 PC Remote Control application. This Windows® 2000/XP/Vista/7/8 application allows you to do even more with the 5500 than you can do through its front panel, making remote control a pleasure.
5500 PC Remote software allows you to access all 5500 features and allows you to archive and restore presets, automation lists, and system setups (containing I/O levels, digital word lengths, GPI functional assignments, etc.)
Built-in clock-based automation lets you automatically day-part the processing. You can control many other 5500 operating parameters too.
The 5500's feature set fully exploits the processor's DSP and computer-based control architecture. To ensure absolute accuracy, you can automatically synchronize the clock to an Internet timeserver. It has a cool-running, energy-efficient switching power supply and uses the latest dual-core DSP chip technology from Freescale Semiconductor.
GENERAL DATA
Power Supply 220 / 110V 25 VA
Dimension 434x351x44mm (1 rack unit)
Weight » 4 Kg
MEETING INTERFACE IN / OUT
Connector DB 9 female
Nominal in / out audio level 0 dBm
Input impedance 600 W / 10 KW (selectable)
Output impedance 100 W
* nominal line level: - 6 dBm
** it can vary depending on characteristics of telephone line
All measurements are intended at 1 kHz.
AUDIO PROGRAM IN / OUT
Connectors XLR, electr. balanced
Input impedance 600 W / 10K W (selectable)
Output level * - ¥ ¸ + 16 dBm
Output impedance 100 W
Noise on Receive output
2-Wire separation £ 25 dB**
4-Wire separation £ 70 dB
2-WIRE SECTION
Connector RJ11
Nominal input level - 6 dBm
Nominal output level - 6 dBm
Compensation mode Electronic, transf. decoupled
Impedance 600 W
4-WIRE SECTION
Connector Terminal block
Impedance 600 W
Nominal TX level 0 dBm
Nominal RX level 0 dBm
Product Features:
Ultra-high resolution 24-bit/96 kHz mastering processor featuring 32/40-bit floating-point DSP technology Audiophile 24-bit/96 kHz A/D- and D/A converters offering 113 dB dynamic range 4 concurrently selectable EQ modules (31-band graphic EQ, 10-band parametric EQ, Feedback Destroyer plus 3 Dynamic EQs per stereo channel) Ultra-high resolution 61-band real-time FFT analyzer with additional auto EQ function for room and loudspeaker equalization Unique VPQ (Virtual Paragraphic EQ) option allows parametric control of graphic EQs State-of-the-art compressor/expander with peak limiter per stereo channel, additional stereo imager and stereo delay for delay line applications Multi-functional level meters (peak/RMS, VU and SPL meter with dBA/dBC weighting via RTA/Mic input) 64 user memories for complete setups and/or individual module configurations Separate mic/line input with phantom power for RTA and Auto-EQ applications Balanced inputs and servo-balanced outputs with gold-plated XLR connectors, stereo aux output, AES/EBU and S/PDIF inputs and outputs (XLR and optical) Professional Wordclock input and MIDI connections for full remote control, preset dumps and system updates Open architecture allowing future software updates via MIDI "Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving High-quality components and exceptionally rugged construction ensure long life Conceived and designed by BEHRINGER Germany
Renaissance Compressor
Designed to provide the classic warm sound of analog compressors, the legendary
Renaissance Compressor controls dynamics with studio-style warmth that flatters
full mixes, vocals, or instruments. Controls include selection of vintage-style Opto
or modern Electro compression, and threshold, ratio, and attack controls. Waves
ARC? (Automatic Release Control) algorithm dynamically optimizes the compressor's
release value for a wide-ranging input. ARC? reacts much the way a human ear
expects, and can produce increased RMS level with greater clarity.
In general, the release is faster for peak transients and slower for the overall RMS
level. The ARC? system varies the release time to fit the ear's expectations while
increasing RMS, and without creating distracting artifacts. In this way, the
Renaissance Compressor can serve as a leveler plus a fast compressor simultaneously.
L2 Ultramaximizer Peak Limiter
Heard on countless hit records and soundtracks, the L2 Ultramaximizer puts sound
up-front with breathtaking transparency. The L2 is capable of a very fast, overshoot-free
response. Once the limiter threshold has been set, you can define the actual peak level
that the processed signal will reach. Once set, limiting and level re-scaling becomes a
one-shot process. The L2 can significantly increase the average signal level without
introducing any audible side effects. Yet there is plenty of range to recreate "vintage"
effects such as level pumping or severely limited dynamic range if you like.
Pristine Sound Quality
The MaxxBCL offers 96kHz, 24-bit resolution with a 48-bit, double precision internal
processing path and a dynamic range of ~125dB. The totally passive analog input
path to the ADC uses Jensen transformers, while the output path also features Jensen
analog output transformers. The unit is galvanic-isolated, which prevents ground loops
and allows it to operate in electrically unstable environments. Waves MaxxBCL combines
the highest quality converters available with unequalled processing algorithms to offer you
astonishing new power in bass enhancement, dynamics processing, and format conversion
(analog-to-digital, digital-to-analog, and digital re-quantization).
Versatile Connections
The MaxxBCL supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced
line-level analog signals. MaxxBCL features a unique set of input and output trim settings:
analog input headroom can be set from 9dB above 0dBu to 24dB in six precise steps
(using the rear-panel selectors). Analog output level is similarly set with a separate
rear-panel trim pot offering you the ability to connect between devices with a wide range
of input and output levels.
Waves MaxxBCL Features:
User Interface:
Clear backlit displays, meters, and buttons are visible in all lighting conditions
THD + Noise: ? 0.0006 % @ 1kHz @ -1dBFS
Precision metering with resettable peak hold options (2 sec, infinite)
Accurate, wide-range metering covering 90dB for input and output
and 12dB for compressor and limiter attenuation
Quick access independent bypass on each processing block
Tactile feedback knobs
Four easy store/recall user presets
Input / Output:
Analog, AES/EBU, S/PDIF
Independent rear-panel input and output headroom calibration in six steps
(+9, 12, 15, 18, 20, and 24 dBu)
Passive analog inputs to the A-to-D converters using Jensen analog input transformers
Jensen analog output transformers
High-performance IDR dithering to 16- or 24-bit output
Precise input level setting using 1% resistor networks
Processing:
48-bit end-to-end internal processing path
Switchable compressor/MaxxBass? order
MaxxBass:
Adjustable processor frequency from 25 to 120Hz
Adjustable harmonic mix percentage from 0 to 100%
High-pass Filter "harmonics only" option
Compressor:
Opto/Electro mode selection
Threshold (0-60dB), Ratio (1:1-12:1), and Attack (0.5, 1, 2, 5, 10, 20, and 50 ms) controls
Proprietary ARC? Automatic Release Control
Automatic gain makeup
Limiter:
Overshoot-free look-ahead processing
Adjustable Threshold (0-18dB)
Adjustable Output Ceiling (0-18dBFS)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.