DYNACORD H-5000 POWER AMPLIFIER 2x 2500 Watt / 4 Ohm

Dynacord H 5000

 
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.  

 
Dynacord H 5000 features:

    2x 1500 Watt / 8 Ohm
    2x 2500 Watt / 4 Ohm
    2x 3500 Watt / 2 Ohm
    Cooling: Front-to-Rear, 5-stage-fans
    Dimensions (WxHxD): 483 x 88.1 x 498 mm
    Weight: 14.5 kg
    Protections:
    Audio limiters
    High temperature
    DC
    HF
    Short Circuit
    Back-EMF
    Peak current limiters
    Inrush current limiters
    Turn-on delay
    Mains Circuit Breaker Protection
    Mains Overvoltage Protection

Model T5n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2500
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 5000
8Ω bridge 4400
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 3400
4Ω per channel 2200
8Ω per channel 1350
4Ω bridge 6800
8Ω bridge 4400
SN ratio (20Hz-20kHz) 107dB
THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U)

A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Ισχύς 2 x 1050 Watt / 8Ω RMS, 2 x 1650 Watt / 4Ω RMS, 3000 Watt / 8Ω bridge RMS. Weight: 13 κιλά. 
 

Stereo Mode Ratings (Both Channels Driven):

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 1050W
    - EIA 1 kHz, 0.1% THD: 1100W
    4 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 1600W
    - EIA 1 kHz, 0.5% THD: 2000W (1% THD)
    2 ohms:
    - EIA 1 kHz, 1% THD: 2500W
    70V Direct Drive:
    - EIA 1 kHz, 1% THD: 2500W
    100V Direct Drive:
    - EIA 1 kHz, 1% THD: 1000W

Bridged Mono Mode Ratings/Specifications:

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 3200W
    - EIA 1 kHz, 0.1% THD: 3600W
    4 ohms:
    - EIA 1 kHz, 1% THD: 5000W
    70V Direct Drive:
    - EIA 1 kHz, 1% THD: 5000W
    100V Direct Drive:
    - EIA 1 kHz, 1% THD: 3600W
    Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
    Input Sensitivity @ 8 Ohms: 1.42V (+5.3 dBu)
    Voltage Gain @ 8 Ohms: 64x (36 dB)
    Output Circuitry: 3-tier Class H
    Power Requirements (120V):
    - 1/8 power pink noise at 4 ohms: 13.9A
    - 1/3 power pink noise at 4 ohms: 26.9A
    Power Requirements (230V):
    - 1/8 power pink noise at 4 ohms: 7A
    - 1/3 power pink noise at 4 ohms: 13.5A
    Distortion (SMPTE-IM):

Power Output Level R-300 PLUS

STEREO
8ohm(T.H.D 0.05%)  170W+170W
4ohm(T.H.D 0.05%)  250W+250W

BRIDGED MONO
8ohm(T.H.D 0.05%)  460W
8ohm(T.H.D 0.5%)    500W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10kΩ@0.775V Inputs