T-REX Fuel Tank Junior Multi Powersupply

Power supply with voltage selector, 115/230 volts and 5 x 9VDC isolated outputs (120 mA each).

• Choice of 9V DC, 12V DC, 12V AC or 18VDC -150mA
• Noise-cancelling galvanic isolated outputs
• Traditional EI Transformer
• Several different voltage types served
• Current doubler = the possibility of as much as 600 mA
• Switchable 115V or 230V
• Compact, rugged, road-ready design

User\'s manual

• Universal 9 volt DC power supply
• 5 outlets with ultra stable 250 mA each
• Isolated
• Overload protection
• Roadworthy enclosure
• Mounting and strain relief options
• Power, merge and daisy chain cables included

With a stable 250 mA on each of the five center negative barrel style outlets the compact Palmer PWT 05 MK2 is most suited to virtually any pedalboard size. To deliver clean DC power to your pedals and eliminate ground loops between them and the associated hum the outlets are isolated.

The PWT 05 MK2 is protected against overloading and comes with 25 and 50 cm long connection cables, as well as two Y-cables. The first one, with a black connector, connects two 9 V outputs to increase the current intensity to a massive 500 mA, the other one, with a white connector, connects two 9 V outputs to double the voltage to 18 V.. Also included is a 1-into-5 daisy chain that lets you power five pedals from one output if their total current draw does not exceed 250 mA. The rugged enclosure of the Palmer PWT 05 MK2 provides mounting and cable relief options while the IEC mains inlet and voltage selector enable worldwide use.

Power Supply Unit for effects Pedals and Amplifiers

Universal Effects Pedal Floor Board with 9 V DC Power Supply and Patch Cables
Ultra-compact and lightweight pedal board for transporting up to 6 effects pedals, including patch cables
Generous 1.7 A power adapter included for powering more than 12 devices*—includes 1 x 6 daisy-chain cabling
Ultra-rigid plastic design withstands even heavy impact
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

When effects are an integral part of your rig, their power adapters and patch cables can often be the most vulnerable part, and the most likely to sabotage your set if they're not pampered. Rather than tossing your pedals, power adapters and all other cabling into a duffel bag after a gig, keep them safe—and ready to rock at a momentʼs notice—with the PB600.
It's All About Connections
This awesome pedal board makes hooking up six 2.5" x 4.5" pedals as easy as hooking up just one (of course, if youʼre using pedals that arenʼt 2.5" x 4.5“, the snug foam padding can be cut to accommodate pedals of varying shapes). The PB600 includes 1/4" patch cables, so you can leave your pedals connected to one another, ready to pass signal even when youʼre transporting them. It also comes with 1 x 6 daisy chain cabling so that when you plug in the 1.7 A power adapter, all your pedals receive power. Meanwhile, all cabling remains safe and free of strain. Failure is almost guaranteed when youʼre dealing with a ratʼs nest of loose cabling, but with the PB600, your effects chain is always safe and organized.

When itʼs time to load out, just unplug the power supply, disconnect your guitar and amp, put the lid back on the PB600 and slide the locking latches back into place. The heavyimpact plastic casing will protect your pedals from the very worst dings, scrapes and scratches the road throws your way.

User's Manual

• Fully regulated universal pedalboard power supply
• 4 standard centre negative outputs with 1,000 mA output total
• Short circuit and overload protection for each outlet
• DC cables and mains adapter included