| Content |
HPS 2500 is a 2 channel power amplifier that delivers up to 2 x 1400 W RMS @ 2 Ω (2800 W RMS bridged @ 4 Ω).
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.
| Features |
|---|
| Fast response and low distortion | | Easy to configure in stereo / mono / bridge modes | | Extensive protective circuits ensure high reliability and operating safety | | Front panel signal / clip / protect LED indicators | | Minimum load impedance (stereo / mono): 2 Ohm | | XLR input connectors | | SPEAKON output connectors | | 2 unit 19" rack, low weight for easy transportation | | Switchable Limiter |
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 2Ω: | 2 x 1400 Watt rms | | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | | Power output stereo 8Ω: | 2 x 700 Watt rms | | | Power output bridged 4Ω: | 2800 Watt rms | | | Power output bridged 8Ω: | 2200 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | 106 dB | | | Damping factor: | > 300 | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | xlr | | | Input sensitivity: | 1.4 dBm/V RMS | | | Input impedance: | 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ | |
| OUTPUT SECTION |
|---|
| Output connector: | Speakon | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Forced | | | Voltage gain: | 32 – 26 dB | | | Amplifier class: | H | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220 ÷ 240 V (50 / 60 Hz) V ~ Hz | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88/3.4 mm/inch | | | Width: | 482/18.9 mm/inch | | | Depth: | 420/16.5 mm/inch | | | Net Weight: | 19/41,8 Kg/Lbs |
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
| 1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
| 4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
| 8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
| Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
| Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
| P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
| 2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
| 4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ | Crown XTi 4002 Features at a Glance:
* Stereo Wattage: 1600W @ 2 ohms, 1200W @ 4 ohms, 650W @ 8 ohms
* Bridged Mono Wattage: 2400W @ 8 ohms, 3200W @ 4 ohms
* Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
* Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
* 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
* New system monitoring provides software visibility of AC line voltage and power supply temperature
* Integrated cast-aluminum handles for easy handling and enhanced durability
* Locking power cord clip provides a secure connection between the amplifier and power cord
* Updated HiQnet Band Manager and System Architect control software
* Increased number of presets to a total of 30; 29 of which are user definable |
Crown DSi 4000 2x1200W-4Ω Power Amplifier
The Crown? DSi 4000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 1,600W with 1% THD, 4 ohm
Stereo (per channel): 1,200W with 0.5% THD, 8 ohm Stereo (per channel):
650W with 0.5% THD, 4 ohm Bridge-Mono: 3,200W with 1% THD, 8 ohm
Bridge-Mono: 2,400W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.61V.
Sensitivity at 4 ohm rated output: 3.47V.
Sensitivity at 2 ohm rated output: 2.84V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 8.0A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass
gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is ?DSP OFF.? Fifteen are factory-set for JBL Cinema
systems. Four are user-defi nable.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airflow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
The amplifier shall be designated the Crown DSi 4000.
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the
face of serious power supply limitations. Refinements throughout this expanded five-model lineup
make these amplifiers the new benchmarks for quality, reliability, and versatility in professional
applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 750 Watt / 8Ω RMS,
2 x 1150 Watt / 4Ω RMS, 2300 Watt / 8Ω bridge RMS. Weight: 12,5 Kg. | 2x1350W/4Ω-1000W/8Ω-1Χ2700W
Crown XLI 3500
The Crown XLI 3500 is a reasonably priced, but robust and powerfull power amplifier. It suits ideally for the use in budget-oriented applications at mobile and stationary area. It offers a power of 2 x 1800 W / 4 Ohm. Thereby the integrated fan guarantees a high operating safety, due to the constant airstream for cooling the power amplifier. The XLI 3500 offers a robust an analogue circuit, which is supplied by a conventional power supply. Furthermore it features three different, selectable modes (stereo, bridge and parallel).
Crown XLI 3500:
- Reasonably priced, robust and powerfull power amplifier
- Robust and analog circuit
- LED display for each channel for signal, clip and error
- Stereo, bridge and parallel modes
- Conventional power supply
- Performance: 2 x 1200 W / 8 Ohm, 2 x 1800 W / 4 Ohm
- Inputs: Cinch, XLR
- Outputs: 2 x speakon, spring clip
- Robust 19 inch housing
- Hight: 2 hight units
Specifications
|
XLi800 |
XLi1500 |
XLi2500 |
XLi3500 |
| Channels |
2 |
2 |
2 |
2 |
| Sensitivity (full rated power at 8 ohms) |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
| Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted) |
> 100 dB |
> 100 dB |
> 100 dB |
> 100 dB |
| Total Harmonic Distortion (THD) (20Hz - 20kHz) |
|
|
|
|
| Inter Modulation Distortion (60Hz and 7kHz at 4:1 from full rated output to -40 dB) |
= / |
= / |
= / |
= / |
| Frequency Response (at 1W, 20Hz - 20kHz) |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
| Crosstalk (below rated power) |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
| at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
| Damping Factor (from 10Hz to 400Hz, 8 ohms) |
> 200 |
> 200 |
> 200 |
> 200 |
| AC Line Voltage and Frequency Configurations (± 10%) |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
| 220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
| 230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
|
|
|
|
|
| Dimensions (H x W x D) |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 14.4“ |
| (89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 366mm) |
| Net Weight |
25.1 lb (11.4 kg) |
28.0 lb (12.7 kg) |
29.7 lb (13.5 kg) |
43.0 lb (19.5 kg) |
| Net Shipping Weight |
29.5 lb (13.4 kg) |
32.4 lb (14.7 kg) |
34.2 lb (15.5 kg) |
47.4 lb (21.5 kg) |
|
Reviews
There are no reviews yet.