KORG KA-189 AC Adaptor Suited For AX10G and AX10B, AX1500G Effects Pedals

The Korg KA189 Power Supply is a power supply, for microKORG, Electribe A,R,S, microKONTROL, padKONTROL, SDD-3000 PEDAL, AX1500G, AX3000G/B, D3, VOX Dynamic Looper, VOX-JS, Cooltron, with 9V voltage, and 1100mA output current.

The main features of the Korg KA189 Power Supply include:

• Suitable for: microKORG, Electribe A,R,S, microKONTROL, padKONTROL, SDD-3000 PEDAL, AX1500G, AX3000G/B, D3, VOX Dynamic Looper, VOX-JS, Cooltron
• Voltage: DC
• Output Current: 1100 mA
• Output Voltage: 9V

Input voltage DV 9V Output Amps 300 mA

User\'s manual

• Fully regulated universal pedalboard power supply
• 8 standard center negative outlets with 2,000 mA output total
• Two 9, 12 or 18 V switchable outputs
• Short circuit and overload protection for each outlet
• Bright power and outlet status LED indicators
• DC cables, Y cable and mains adapter included

The PWT 08 is a universal pedalboard power supply with huge 2,000 mA output capacity and 8 standard center negative outlets. Two of these are switchable to 9, 12 or 18 volts, and with the included Y cable they can be combined to a single outlet for 21, 24, 30 or 36 volts maximum output. They are isolated from each other and the remaining outlets. Featuring short circuit and overload protection, the PWT 08 is fully regulated to deliver constant voltage. The unit sports a power on LED, bi-color outlet status LEDs and comes with a set of DC cables and dedicated mains adapter. The PWT 08 is the ideal choice if you have just one or two power hungry pedals or 9 volt effects that can be run on higher DC currents for more dynamics and headroom.

 4,5 Volts Power Supply for KORG PX4 and PX4R.

Universal Effects Pedal Floor Board with 9 V DC Power Supply and Patch Cables
Ultra-compact and lightweight pedal board for transporting up to 6 effects pedals, including patch cables
Generous 1.7 A power adapter included for powering more than 12 devices*—includes 1 x 6 daisy-chain cabling
Ultra-rigid plastic design withstands even heavy impact
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

When effects are an integral part of your rig, their power adapters and patch cables can often be the most vulnerable part, and the most likely to sabotage your set if they're not pampered. Rather than tossing your pedals, power adapters and all other cabling into a duffel bag after a gig, keep them safe—and ready to rock at a momentʼs notice—with the PB600.
It's All About Connections
This awesome pedal board makes hooking up six 2.5" x 4.5" pedals as easy as hooking up just one (of course, if youʼre using pedals that arenʼt 2.5" x 4.5“, the snug foam padding can be cut to accommodate pedals of varying shapes). The PB600 includes 1/4" patch cables, so you can leave your pedals connected to one another, ready to pass signal even when youʼre transporting them. It also comes with 1 x 6 daisy chain cabling so that when you plug in the 1.7 A power adapter, all your pedals receive power. Meanwhile, all cabling remains safe and free of strain. Failure is almost guaranteed when youʼre dealing with a ratʼs nest of loose cabling, but with the PB600, your effects chain is always safe and organized.

When itʼs time to load out, just unplug the power supply, disconnect your guitar and amp, put the lid back on the PB600 and slide the locking latches back into place. The heavyimpact plastic casing will protect your pedals from the very worst dings, scrapes and scratches the road throws your way.

User's Manual