Content |
Compact and portable at 15 lb, this pair of CR5BT Multimedia Monitors from Mackie provides audio playback in home and studio environments. As such, they are useful for mixing music or post-production sound, and they boast Bluetooth capability to boot.
The pair consists of one passive un-powered monitor and one Class AB amplifier-powered monitor that you can connect with an included stereo cable. For the low-end, these speakers utilize 5" polypropylene-coated woofers and a rear port tube, while the highs are handled by 0.75" silk dome tweeters; all of this ensures a frequency response of 60 to 20,000 Hz with a maximum SPL of 103 dB.
A switch allows you to select whether the powered speaker will function as the left or right monitor. This is particularly helpful when you must position the speakers near power outlets, or when you have to decide whether you'd rather have your front-panel volume knob situated on your left or right. Also adorning the monitor's front are an LED (indicating whether or not your monitors are on at any given time) and a dedicated headphone output (for private listening; please note that plugging your headphones in will silence the monitors themselves).
You can connect mobile devices and other devices directly to the monitors via 1/8“, 1/4" or RCA inputs—but then again, feel free to skip all that and just go with Bluetooth. The monitors also come with isolation pads for reducing the transmission of structural vibrations.
- RCA, 1/8“, and 1/4" TRS balanced and unbalanced inputs
- Supports Bluetooth and stereo headphones
- Lightweight at 15 lb
- Switchable L/R configuration for convenience
- On-board volume knob
- Wood cabinet
- Multiple necessary cables included
Frequency Response
| 60 Hz to 20 kHz at -3 dB
50 Hz to 20 kHz at -10 dB | Maximum SPL | 103 dB | Crossover Frequency | 3 kHz | Low Frequency Transducer | 5.0" / 127 mm polypropylene-coated woofer | High Frequency Transducer | 0.75" / 19 mm silk dome tweeter | Amplifier (Power) | 28 W RMS / 50 W Peak | Class | AB | Input Type | Balanced / unbalanced 1/4" TRS, unbalanced RCA (Rear), 1/8" TRS (Front) | Input Impedance | 20 kOhms balanced bridging
10 kOhms unbalanced | Output Type | 1/8" stereo headphones (front) | Bluetooth | Bluetooth Protocol: 3.0
Bluetooth Function: Audio streaming | Enclosure | Solid MDF | Finish | Black vinyl wrap | Port Configuration | Custom-tuned rear port tube | Damping | Adiabatic batting | Operating Temperature | 32 to 104°F / 0 to 40°C | Power Requirements | United States: 120 VAC, 60 Hz | Power Consumption | 72 W with music, loud mix | Dimensions ( H x D x W) | 10.2 x 6.9 x 9.0" / 259 x 175 x 229 mm | Weight | 15 lb / 6.8 (pair) |
|
Features of the HR824mk2 Studio Reference Monitor:
- High-resolution Active studio reference monitor
- Ultra-linear frequency response for accurate mix translation
- 8.75 in. high-precision, low-distortion LF transducer
- 1 in. titanium dome, ferrofluid cooled tweeter
- Optimized Waveguide for wide, even sweet zone
- Twin FR Series amps -- 150W for LF / 100W for HF
- Cast aluminum Zero Edge Baffle minimizes diffraction
- Full internal damping eliminates midrange artifacts
- Onboard passive radiator extends bass response to 35Hz
- Acoustic Space, LF roll-off, and HF controls
- Balanced XLR, TRS, and unbalanced RCA inputs
- OmniMount ready for easy wall/ceiling placement
- THX pm3 certified for surround sound applications
- Perfect for High Definition audio, cinema and gaming systems
Dimensions and Weight in PackagingShipping Weight: 41 lbs Shipping Dimensions: 14 x 18 x 22 in
|
The Solo6 Be monitor will surprise you in the very first minutes you spend with it, partly due to its size/extended bass response (40Hz at -3dB). The 6.5" "W” composite sandwich mid-woofer combines neutrality in the midrange, fullness in the midbass register and bass control. Its compactness and the choice of a large front laminar port guarantee easy integration in studios that need a near field monitor without any acoustic compromise. The user settings on the back of the Solo6 Be, combined with its compactness, make it easy to carry and to adjust according to the acoustics of each studio.
Specifications Frequency response : | 40Hz - 40kHz | Maximum SPL : | 113dB SPL (peak @ 1m) |
Input :
|
Type/Impedance: symmetrical/10 kOhms
Connector: XLR
Sensitivity: Adjustable, +4dBu or -10dBV
| Bass/mid-range : | 150W rms, BASH® technology | Treble : | 100W rms, AB class |
Electric supply :
|
Local supply power: 230V (1.6A fuse)
115V (3.5A fuse)
Connection: removable IEC supply wire
|
Visualization and control :
|
Input sensitivity selector
Adjustable tweeter and woofer levels with potentiometers
Power On/off switch
Voltage selector
| warning light : | Power on LED |
Electric supply :
|
Local supply power: 230V (1.6A fuse)
115V (3.5A fuse)
Connection: removable IEC supply wire
| Woofer : | 6W4370B, 6-1/2" (16.5cm) Focal "W" composite sandwich cone speaker | Tweeter : | Focal TB871 Beryllium inverted dome tweeter | transducer shielding : | Integral through cancellation magnets or by magnet design | Box : | 7-1/2" (19mm) MDF panels |
Finish :
|
Dark red natural veneering side panels, black body
| Dimensions (HxWxD) : | 13 x 9-7/16 x 11-7/16 " (330x240x290mm) | Weight : | 24.2lb (11kg) |
|
The Genelec 8130A Digital Monitoring System has a 192 kHz/24 bit digital audio interface.
Due to its compact size, integrated construction, excellent dispersion and precise stereo
imaging, the 8130A is ideal for near field monitoring, mobile vans, digital audio workstations,
broadcast and TV control rooms, surround sound systems, home studios, multimedia
applications and also for use with computer soundcards. The Directivity Control Waveguide?
(DCW?) technology provides excellent frequency balance even in difficult acoustic
environments.
The integrated design allows the amplifiers and the drivers to be calibrated as a single unit,
eliminating the effects of component tolerances and ensuring consistent quality.
The all-aluminium Minimum Diffraction Enclosure? (MDE?) and advanced Directivity Control
Waveguide? (DCW?) technologies are carefully matched with advanced amplifier and electronics
circuitry. The low frequency response extends down to 55 Hz (-3 dB) while distortion is extremely
low due to a uniquely new rear reflex port design.
The 8130A has been specially designed to have a sufficient LF extension for most situations.
However if greater SPL's and a lower cutoff frequency are required, it can be complemented
with Genelec 7050B subwoofer.
The 8130A is very easy to set up and use, the only connections required are the mains supply
and the input signal. The female XLR input connector can be fed with either AES/EBU formatted
digital signal or analog line level audio signal. The Genelec 8130A automatically detects analog or
digital signals and directs them to the correct signal paths.
Technical Specifications
Input word length 16 - 24 bits
Input format AES/EBU
Digital input XLR female
Connector type
Input Sampling rate
No de-emphasis 29 - 200 kHz
Input Sampling rate
Using de-emphasis
Peak per pair with music material 108 dB SPL @ 1m
Drivers
Bass 5" magnetically shielded
Midrange -
Treble 3/4" metal dome, magnetically shielded
Crossover frequencies 3 kHz
Free field frequency
response 58 Hz - 20 kHz (± 2 dB)
Amplifier power /ch
Bass 40 W
Midrange -
Treble 40 W
Speaker dimensions (H x W x D)
mm 285 x 189 x 178 mm (Height with Iso-Pod? 299 mm)
inches 11 1/4 x 7 7/16 x 7 1/16" (Height with Iso-Pod? 11 13/16“)
Amplifier dimensions* (H x W x D)
mm Integrated in the speaker cabinet
inches
Speaker weight 5.6 kg (12.3 lb)
| Behringer MS-16 2x8W 2-Way Active Personal Monitor System
The Behringer MS16 Studio Monitors feature an active 2-way design with powerful 4'' woofers and 1.5'' tweeters, powered by two 8 watt amplifiers. Offering two line inputs and a microphone input, the Behringer MS16 monitors are perfect for both home studios and general multimedia applications.
Full Description
Compact and Ideal For Home Studio
The Behringer MS16 Studio Monitors, Pair are the ideal studio monitor for your home studio project. Whether that be mixing, producing, or even listening the MS16 Studio Monitors turn your computer into a personal home studio. Its powerful 4" woofers provide thumping bass, whilst the high resolution tweeters provide clean high frequencies. Also featured are dedicated volume, bass and treble controls for extra flexibility. They also make excellent add-on speakers for electronic keyboards and playing a live performance.
Input Connections
The MS16 Studio Monitors feature multiple input options featuring a 1/8" stereo input for connecting up CD, MD and MP3 players. The dual RCA jacks allow for stereo keyboard modules and tape decks. Furthermore there is a 1/4" inch to allow connections for a dynamic microphone or electric guitar enabling you to sign or play along with prerecorded tracks.
Features
- Compact stereo speaker system ideally suited for home studios, multimedia applications, keyboard and vocal monitoring, etc.
- Powerful 4'' woofers and high-resolution tweeters powered by two 8 watt amplifiers
- Dedicated Volume, Bass and Treble controls for more flexibility
- Stereo RCA inputs for sound cards, keyboards, etc. that can be used simultaneously with a second stereo source (e. g. CD/MD player) through 1/8'' TRS stereo input
- Separately adjustable 1/4'' TRS microphone input mixable with stereo inputs for playback and vocal monitoring applications
- 1/8'' TRS headphone connector with auto-mute loudspeaker function
- Magnetically shielded for placement near computer monitors
- Designed and engineered in Germany
Specifications
- Woofer: 4''
- Tweeter: 1.5''
- Output Power: 2 x 8 Watts
- Frequency Response: 80Hz - 20kHz
- Speaker Impedance: 4?
- Input 1:
- Connector: 1/8'' TRS Stereo
- Input Level: -10dBm, 10k?
- Input 2:
- Connector: RCA Stereo
- Input Level: -10dBm, 10k?
- Mic Input:
- Connector: 1/4'' TRS
- Input Level: -50dBm, 50?
- Dimensions: 9.5'' x 5.5'' x 6'' / 241mm x 140mm x 150mm (H x W x D)
- Weight: 4kg
|
MYTHO 6 is a two-way reference studio monitor that features a high quality large metal dome tweeter for the best vocal reproduction and a 6” neodymium vented woofer with a large sized 51 mm voice coil that guarantees very high energy for tight and controlled bass reproduction and perfect thermal stability with minimum power compression.
The magnetic circuit features a special air ventilation to reduce air compression, air noises and minimize distortion in large excursion situations. The MYTHO 6 is equipped with two separate amplifiers: 200 W for the low frequencies and 100 W for the high. The design is a classic AB circuit, unparalleled for low distortion and natural sound. The signal processing is executed from a dedicated high quality DSP processing. It features a solid aluminium cabinet internally braced and reinforced to improve low frequencies behaviour and reduce resonances.
Acoustical Specifications |
---|
Frequency Response -3 dB: | 40 Hz | ÷ 20 kHz | Max SPL: | 114 dB | | Horizontal coverage angle: | 110° | | Vertical coverage angle: | 70° | | Compression Driver: | 1" neo, metal dome | | Woofer: | 6.5" neo, ICC technology | |
INPUT/OUTPUT SECTION |
---|
Input connectors: | combo XLR/Jack | | Input sensitivity: | -6/+6 dBu | |
PROCESSOR SECTION |
---|
Crossover frequencies: | 1900 Hz | | Protections: | thermal, excurs., rms | | Limiter: | soft limiter | | Controls: | bass tilt, roll-off, treeble tilt, desktop, DSP controlled | |
AMPLIFIER SPECIFICATIONS |
---|
High frequencies: | 100 Watts | | Low frequencies: | 200 Watts | | Cooling: | convection | | Connections: | vde | |
CABINET |
---|
Cabinet Material: | die cast aluminum | | Hardware: | orientation adjustable stand | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 370/14.5 mm/inch | | Width: | 265/10.4 mm/inch | | Depth: | 250/9.8 mm/inch | | Net Weight: | 10.5/23 Kg/Lbs |
|
Reviews
There are no reviews yet.