Content |
Two-way active full range with DSP. 1500W
15'' woofer, 3'' driver, 50 x 40 dispersion.
1000W + 500W class D power amplifier.
Optional: LD2.4 USB interface for remote PC connection.
CV-Spot protective cover. NOTE : SPOT 1500 can not drive the bass cabinet SPOT15B.
|
JBL VP7315-64DPAN Powered 15'' 3-way 1100W RMS Loudspeaker System
Key Features : Powered bi-amplified full-range loudspeaker with JBL DrivePack? technology for portable or installed use.
2200 Watts peak output power, 1100 Watts continuous.
HiQnet? compatible; network control.
15-inch Differential Drive? low-frequency driver for extended low-frequency output.
60° x 40°coverage.
Stylized and ergonomically designed powder-coated die cast aluminum handles.
Six 3-inch fly track suspension points and fourteen M10 fittings (optional detachable flying fittings and forged eye bolt kits available).
Optional DPCN (CobraNet?) digital audio input module available. Specifications:
Frequency Range |
: |
34 Hz to 20 kHz (-10 dB) |
Frequency Response |
: |
43 Hz to 18 kHz ( ± 3 dB) |
Coverage Pattern |
: |
60°x 40° rotatable waveguide |
Directivity Factor (Q) |
: |
15.85 |
Directivity Index (DI) |
: |
12 dB |
Maximum Peak Output1 |
: |
138 dB SPL 1m |
Transducer Section |
|
|
Low Frequency Section |
: |
JBL 2265G, 381mm (15 in) dia., 76mm (3 in) Dual Coil neodymium Differential Drive?, Direct Cooled |
Bandpass Nominal Impedance |
: |
4 ohms |
Mid/High Frequency Section |
: |
|
Mid Frequency |
: |
JBL CMCD-82H, 200mm (8in) Dual Coil Differential? transducer |
High Frequency |
: |
JBL2452H-SL, 100mm (4in) titanium damped diaphragm, 1.5in. exit |
Waveguide |
: |
JBL PT-K64-MHF |
Bandpass Nominal Impedance |
: |
8 ohms
|
System |
|
|
DP2 Internal Amplification Output (at nominal load) |
: |
2200 Watts Peak, 1100 Watts Continuous |
DP2 Output (Continuous IEC shaped pink noise into rated load impedance) |
: |
750LF/350HF Watts |
DP2 Output Section |
: |
2-Channel, Class I |
Audio Input connector: |
: |
XLR with loop-through |
Network Control Connector |
: |
Ethernet, RJ45 |
Signal Processing |
: |
DSP Based, resident in Input Module |
System Management
|
: |
DSP based limiters for mechanical and thermal protection |
AC Power Operating Range |
: |
Auto Select 90-132VAC/ 216-264VAC, 50/60Hz
|
AC Line Voltage |
: |
50/60 Hz, Auto-Detect; 120V/ 240V (-15%, +10%) |
AC Input Connector |
: |
Neutrik PowerCon |
AC Loop-Thru |
: |
Neutrik PowerCon |
AC Current Requirement |
: |
6A per system at 120V, 3A per system at 240V |
Enclosure |
|
|
Box Construction |
: |
5/8in. multi-ply exterior grade Baltic birch. Internally braced. Black DuraFlex? finish.
|
Suspension System |
: |
6 standard air-cargo 3 in. track and 12 M10 fittings
|
Grille |
: |
14 Gauge Black powder-coated perforated steel with foam backing
|
Dimensions (H x W x D) |
: |
914.4 x 528.3 x 624.8mm (36 x 20.8 x 24.6 in) |
Net Weight |
: |
44 kg (97 lb) | |
Inside our rigid custom designed cabinet is a 15" driver designed exclusively for this project. It's matched with a new 1.75" Titanium high frequency driver, aimed through a 1" diameter horn. The dB500a features 500 watts of clean power (400 watts low frequency/100 watts high frequency) and has a crossover designed for high SPL. Our exclusive Optimax(TM) signal processing circuitry provides total speaker protection but won't cut the low end at high volumes, as similar speakers with sliding filters do.
The back panel has a built-in mixer-like preamp section with mic and line inputs, XLR connectors and level controls. Controls for the selectable low pass filter and Optimax processing are also included.
The dB500a speaker cabinet features an array of mounting options. Designed with floor monitoring in mind, they are also easily stacked or permanently installed. A 1 3/8" pole receptacle is built in, and 10 reinforced fly points are available.
|
Powerful, Lightweight PA Speakers for Any Application You'll be impressed by how easy it is to fill a room with powerful, pristine sound with Turbosound Milan M15 powered loudspeakers. This 15-inch, 1,100-watt speaker is perfect for live music applications, and just as appropriate for schools, churches, or even corporate A/V installations. The coverage is wide and consistent, and doesn't sound strange when you get out of the main coverage area - some of the major factors Sweetwater considers when we're designing live sound systems. Whether you use it as a PA speaker or a stage monitor you can expect tight and powerful lows, rich and detailed mids, and smooth highs from the Milan M15.
Turbosound Milan M15 Powered PA Speaker at a Glance:
- Composite cabinet makes this powerful speaker strong and lightweight
- Flexible input options for virtually any application
- Designed to serve double-duty as a floor monitor too
Composite cabinet makes this powerful speaker strong and lightweight
You'll notice the Milan M15 is remarkably lightweight for a 15-inch PA speaker, at just over 60 pounds. That's due to the cabinet design, which is made from injection-molded polypropylene. And if you look close you'll see a ribbed pattern on the cabinet's exterior (it's actually on the interior as well). That ribbing not only adds strength and rigidity, it also helps cut down on cabinet resonance. Basically, the Milan M15 lets you take advantage of a lighter, stronger design without compromising your sound quality.
Flexible input options and sound shaping for virtually any application
You can connect practically any sound source to the Milan M15, from your mixer's line outputs to instruments and microphones. And you've got two inputs available, so the Milan M15 is a perfectly viable solution for coffee shop performances with a guitar and vocal mic. It's also perfect for public speaking - in fact, there's a Speech/Music mode switch that optimizes the performance for those applications.
Designed to serve double-duty as a floor monitor too
The powerful sound and lightweight design make the Milan M15 an ideal main PA speaker, it's designed to serve you well as a stage monitor too. The trapezoidal design doesn't just make it easy to handle, it also angles the Milan M15 up at you when you place it on the side. Switch on the 100Hz low-cut filter, and now you've got a sweet-sounding floor monitor that won't add rumble to your stage sound.
Turbosound Milan M15 Powered PA Speaker Features:
- Active PA speaker with 15" LF driver and 1,100W Class-D power amp
- Klark Teknik DSP optimizes your sound with dynamic equalization and intelligent limiting
- Specially-designed waveguide gives you wide, consistent coverage with natural off-axis sound
- Bass and Treble EQ controls let you fine-tune your sound
- Dual-angle pole mount socket makes it easy to position for optimum sound coverage
- Injection-molded polypropylene enclosure is strong and lightweight
- Recessed carry handle makes transport and setup easier
- Front-panel LED indicators indicate if a signal is present, when limiting is occurring, and when signal is clipping
Get the Turbosound Milan M15 for powerful sound in a strong, lightweight design Specification | Detail | Powered | Yes | Power Configuration | Bi-amped | LF Driver Size | 15“ | LF Driver Power Amp | 1,000W (peak) Class-D | HF Driver Size | 1“ | HF Driver Power Amp | 100W (peak) Class-D | Frequency Range | 45Hz-18kHz (±3dB), 40Hz-20kHz (-10dB) | Maximum Peak SPL | 130 dB | Horizontal Coverage Angle | 90 degrees | Vertical Coverage Angle | 60 degrees | Enclosure Material | Polypropylene | Mounting Options | Pole, Floor Wedge, Fly | Inputs | 2 x XLR/TRS combo | Outputs | 1 x XLR | Height | 28.3“ | Width | 18“ | Depth | 14.5“ | Weight | 60.9 lbs. | Manufacturer Part Number | M15UL |
|
GENERAL
The PSA Systems JB-15 is the active variant of the PS-15. This active full range speaker has a built-in amplifier of the bi-amp type and delivers 300 watts RMS. In combination with the active crossover the audio signal is distributed efficiently on a woofer and tweeter. The PSA-15 has a 15-inch woofer, which effortlessly displays the low frequencies, starting at 40Hz. Here he is fed with less than 245 watts. The 1.35-inch compression driver takes it high for his account and get 55 watts of power. This was in fact the RMS power; peaks that are higher are no problem for the amplifier. You are assured of a solid, non-pinched sound.
JB Systems PSA-15 Speaker: Polypropylene
The PSA-15 has a smooth shaped casing made of polypropylene. A light but very strong type of plastic, which is good for long-term protection of the internal components. In addition, he is very practical, with a built-in carrying handle, M8 mounting points, a 35 mm stand adapter and support for monitor use. The latter is excellent as possible, thanks to the angle of the housing.
CONNECTIONS
The back contains the connections with two microphone inputs (XLR, 6.3 mm jack) and a line input (XLR, RCA). The inputs and outputs are balanced. As per the level can be controlled, there is also a master volume and a two-band tone control devices. The PSA 15 is very suitable for mobile use and permanent installation and can be used as PA speaker and be used as a monitor. Monitor Brackets are included. |
Specifications
- LF Amplifier Power (RMS): 1000 watts
- HF Amplifier Power (RMS): 250 watts
- Frequency Response (-3dB): 58-18000 Hz
- Frequency Response (-10dB): 50-20000 Hz
- Max. SPL/1m (calc); half space: 133 dB
- Coverage (nominal -6dB) Horizontal: 90°
- Coverage (nominal -6dB) Vertical: 50°
- LF Transducer: DVX3150
- HF Transducer: ND2
- Crossover Frequency: 1500 Hz
- Enclosure Material: Polypropylene
- Flying: Yes
- Input Connections: XLR
- Chassis Size: 15“
- Speaker Type: Full-range, powered monitors, poweredspeakers, two-way wedges
- Weight (net): 50.49 lbs
- Dimensions (H x W x D): 27.24" x 17.56" x 16.18“
|
Reviews
There are no reviews yet.