OMNITRONIC LH-053 PASSIVE DI BOX

Passive 1-channel DI box, black

• 1 high-impedance signal input, 6.3 mm jack
• 1 low-impedance XLR output
• 6.35 mm jack input, and output
• Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
• Switchable input attenuation: 0 dB, -20 dB, -40 dB
• Rugged black metal housing

Package contents

• 1 x device, 1 x user manual

• No. of channels: 2
• Passive/Actibe: Passive
• Transformer balanced: Yes
• Attenuator: -30 dB
• Input/Output Gain: -20 dB
• Ground lift switch: Yes
• Max Input Level: +54 dBu
• Max Output Level: +4 dBu
• Frequency Range  2K Source Imp. -1dB: 10 Hz - 40 kHz
• Input Impedance  60Hz: 60 kΩ
• Nom. Output Impedance: 600 Ω
• Housing: Steel
• Dimension: 110 x 110 x 45 mm

2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.