A Reamping-Box is mainly used in studios. It allows you to play back a recorded guitar signal and send it to a guitar amp, where it can again be taken and recorded by the microphone. This allows the sound engineer to take time to experiment with the sound of the instrument using different amplifiers.
The DACCAPO box ensures optimal impedance matching and eliminates ground loop hum through the use of a transformer. The signal level to the amplifier can be adjusted with a volume control.
Product type
Product type
DI Boxes
Channels
1
Inputs
1
Input connectors
XLR
Max. input level
+22 dBu
Input impedance
600 Ohm(s)
Outputs
1
Output connectors
6.3 mm jack
Max. output level
+ 22 dBu
Output impedance
100 k Ohm(s)
Frequency response
20 – 20000 Hz
Transformer balanced
Yes
Ratio
Variabel
Controls
Gain
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
125 mm
Depth
80 mm
Height
45 mm
Weight
0,494 kg
Weight
0.29 kg
Reviews
There are no reviews yet.
Be the first to review “PALMER AUDIO DACCAPO Reamping Box Re-Amplification” Cancel reply
Send your signal to an amplifier where it's picked up by microphones and recorded again
The recording engineer can experiment with the sound of an instrument
Takes care of all impedance matching issues
Also eliminates ground loop humming
Content
A Reamping-Box is mainly used in studios. It allows you to play back a recorded guitar signal and send it to a guitar amp, where it can again be taken and recorded by the microphone. This allows the sound engineer to take time to experiment with the sound of the instrument using different amplifiers.
The DACCAPO box ensures optimal impedance matching and eliminates ground loop hum through the use of a transformer. The signal level to the amplifier can be adjusted with a volume control.
Product type
Product type
DI Boxes
Channels
1
Inputs
1
Input connectors
XLR
Max. input level
+22 dBu
Input impedance
600 Ohm(s)
Outputs
1
Output connectors
6.3 mm jack
Max. output level
+ 22 dBu
Output impedance
100 k Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
Yes
Ratio
Variabel
Controls
Gain
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
125 mm
Depth
80 mm
Height
45 mm
Weight
0,494 kg
Inline Transformer IA-2
The model IA-2 line matching transformers !S designed to properly match a low impedance signal to a low impedance source. The advantage of "ground lift" switching allows to optmize hum problems.
Technical Data Frequency response 20 Hz - 20 KHz + 1 dB Impedance 600 : 600 Ohm THD K3 50 Hz = 0.5 % Level < + 6 dBm Weight 100 g Dimensions diameter 17 mm, lenght 115 mm
Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
Compact, high-performance passive direct box
Jack input 1/4" TS in and parallel out
Gold-plated XLR output / impedance balanced
Super-flat frequency output for uncolored sound
Switchable filter that optimizes the DI for guitars
Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
Instruments or amplifier outputs with up to 3,000 watts can be connected directly
Offers impedance and signal matching of instruments to mixers
Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box!
Tech Specs
Type: Passive DI Box
Channels: 1
Ground Lift: Yes
Inputs: 1 x 1/4"
Outputs: 1 x 1/4“, 1 x XLR
Height: 1.4"
Width: 3.75"
Depth: 5"
Weight: 0.66 lbs.
Manufacturer Part Number: DI600P
Phantom or battery powered in a rugged steel chassis
The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo D.I. concepts.
Precision engineered Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade components, plus an all-steel chassis gives excellent hum and noise specifications and superb audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps the stereo image centred.
Level control The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications from the softest keyboard to the hottest broadcast levels.
Battery compartment The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing extremely easy, even on the darkest stages. A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip leads to break, no tools required, no screws to lose. Production crew heaven!
Automatic Phantom switching The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.
Rugged all-steel case A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that is hard to dislodge, and hard to leave behind.
Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus phantom power On LED and captive screw for opening up the unit for battery changing
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all the dynamics,clarity and stereo information of the original sound source transferred to the mixing console. The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal balancing requirements.
T E C H N I C A L S P E C I F I C A T I O N S: Max Input Level +12 dB Phantom powered +6 dB Battery powered Input Impedance 1 Meg Ohm Max Output Level +17 dB 10K Ohm load Phantom powered +12 dB 10K Ohm load Battery powered +11 dB 600 Ohm load Phantom powered +12 dB 600 Ohm load Battery powered Output Impedance 680 Ohms Balanced Output Signal to Noise -100 dB unweighted -104 dB A weighted Dynamic Range 117 dB 10K Ohm load Phantom powered 112 dB 10K Ohm load Battery powered 111 dB 600 Ohm load Phantom powered 107.5 dB 600 Ohm load Battery powered Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056% Frequency Response 20Hz to 20KHz, ± 0.2 dB Gain through Unit: 6dB (Pad switch out) Pad Switch: Global -20 dB attenuation Input and Loop Out Connectors Insulated jacks (!!!Note that Channel A Input connector switches the unit on when a plug is inserted. Remove plug when storing to avoid battery drain!!!) Output Connectors 3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold. Global Audio Ground (Pin 1) lift switch Construction All-steel chassis, fibreglass PCB Battery Access Twist connector opens chassis, snap-in battery holder inside. No tools required
At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.
Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.
As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB12 is for you.
Thru Output: 1 parallel connection from input jack
Connector: 1/4" jack
Type: Unbalanced, RF filtered
Main Output: 1 line level
Connector: XLR male jack
Type: Balanced
Impedance: 150 Ohm typical
Max Output Level: 0dBu
PERFORMANCE
Transformer: Custom dbx mu-metal-shielded
Frequency Response: 20Hz to 20kHz, +/-2.5dB
Noise:
THD:
GENERAL
Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)
Weight: 1.4 lbs / 0.65 kg
Note: Specifications subject to change without notice.
At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.
Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.
As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB10 dB12 is for you.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.