PALMER AUDIO PAN01PRO Pro PAN01PRO – Professional DI Box passive

PAN01 PRO is the deluxe version of Palmer's top selling passive DI box PAN01. It features a 2 mm steel housing and heavy duty metal switches for the PAD and ground lift functions to withstand the rigors of the road and stage. The transformer has been completely redesigned and upscaled with a larger magnet core for increased dynamic range and headroom, and a metal cover for improved shielding. Also, the PAN01 PRO's parallel out is now switchable to double as additional input. This feature enables the summing of a stereo output (e.g. of a keyboard) with the resulting mono signal present at the PAN01 PRO's balanced XLR output.

The PAN01 PRO comes with a high quality reinforced nylon bag with cutouts for connecting the box inside the bag.

The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to
directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors
can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality.
The ADB-1 operates on either phantom power or a 9-volt battery.

FEATURES:
Flat response
Low distortion
Low noise
Wide dynamic range
No transformer
RF protection on input and output
Switchable ground isolation
Flush mounted slide switches

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing

Passive 1-channel DI box, black

• 1 high-impedance signal input, 6.3 mm jack
• 1 low-impedance XLR output
• 6.35 mm jack input, and output
• Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
• Switchable input attenuation: 0 dB, -20 dB, -40 dB
• Rugged black metal housing

Package contents

• 1 x device, 1 x user manual