PV1 Power Amplifier The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years of amplifier design, […]
The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years of amplifier design, this unit takes advantage of rugged TO-3P output devices mounted on massive aluminum extrusions and dissipates heat via an extremely quiet and effective two-speed fan. PV amplifiers are designed to operate at line voltages as low as 50% of nominal, employing mammoth toroidal power transformers and offering impressive specifications and features not found on similarly priced competitive unit\’s. This amp is designed to drive a 2-Ohm load per channel, thus achieving awesome performance levels into 4 Ohms in BRIDGE mode. PV amplifiers are ruggedly constructed, rack-mountable pieces of gear with superb patching capability, allowing superior flexibility in application. Front panel features include calibrated, detented gain (dB) controls and LED indicators for power (PWR), signal presence (SIG), Thermal Protection indicator, and DDT activation on each channel, as well as a rocker mains POWER switch. The back panel contains an IEC connector, line voltage selector switch, dual primary fuses, and the critical cooling fan opening. This opening should have an adequate supply of cool air and should never be blocked or restricted. Also on the back panel are the input and output sections, including an input barrier strip for permanent installations. Each channel input section includes a combo XLR / TRS phone jack connector, THRU/LOW out and HIGH out TRS jacks, and activation switches for the LOW CUT filter and crossover (150 Hz XOVER). Channel output sections feature dual shock-proof binding posts and four-conductor twist lock connectors. An additional four-conductor twist lock connector allows BRIDGE mode output.
PV1 Power Amplifier
The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years of amplifier design, this unit takes advantage of rugged TO-3P output devices mounted on massive aluminum extrusions and dissipates heat via an extremely quiet and effective two-speed fan. PV amplifiers are designed to operate at line voltages as low as 50% of nominal, employing mammoth toroidal power transformers and offering impressive specifications and features not found on similarly priced competitive unit\'s. This amp is designed to drive a 2-Ohm load per channel, thus achieving awesome performance levels into 4 Ohms in BRIDGE mode. PV amplifiers are ruggedly constructed, rack-mountable pieces of gear with superb patching capability, allowing superior flexibility in application. Front panel features include calibrated, detented gain (dB) controls and LED indicators for power (PWR), signal presence (SIG), Thermal Protection indicator, and DDT activation on each channel, as well as a rocker mains POWER switch. The back panel contains an IEC connector, line voltage selector switch, dual primary fuses, and the critical cooling fan opening. This opening should have an adequate supply of cool air and should never be blocked or restricted. Also on the back panel are the input and output sections, including an input barrier strip for permanent installations. Each channel input section includes a combo XLR / TRS phone jack connector, THRU/LOW out and HIGH out TRS jacks, and activation switches for the LOW CUT filter and crossover (150 Hz XOVER). Channel output sections feature dual shock-proof binding posts and four-conductor twist lock connectors. An additional four-conductor twist lock connector allows BRIDGE mode output.
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 4Ω:
2 x 300 Watt rms
Power output stereo 8Ω:
2 x 180 Watt rms
Power output bridged 8Ω:
600 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 105 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
10.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start thermal on transformer
Amplifier class:
H
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
6 A
Power Consumption:
1300 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
350 / 13.77 mm/inch
Net Weight:
11.45 / 25.24 Kg/Lbs
SHIPPING INFORMATION
Package height:
120 / 4.72 mm/inch
Package width:
540 / 21.25 mm/inch
Package depth:
470 / 18.05 mm/inch
Shipping Weight:
13.81 / 30.44 Kg/Lbs
Solid DYNACORD technology for fixed installations at very competitive prices. DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch. The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
<br>
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD<br>
<br>
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)<br>
<br>
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz<br>
<br>
Slew Rate: 15V Per usec<br>
<br>
Damping Factor @ 8 Ohm: 260<br>
<br>
Impedance: 20 Ohms balanced / 10 Ohms unbalanced<br>
<br>
Cooling System: 2 indivdual fans<br>
<br>
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift<br>
<br>
Dimensions (LxWxH): 13.25 "acrobat_reader_logo."){kind=logo}
Reviews
There are no reviews yet.