Content | PV1 Power Amplifier
The PV amplifier features a two-way crossover and sub-sonic (low-cut) filter for each channel. Crossover frequencies are fixed at 150 Hz, allowing subwoofers to be driven at extremely high sound pressure levels, and the filters cut at 40 Hz to prevent low-end rumble. Using proven technology gained through years of amplifier design, this unit takes advantage of rugged TO-3P output devices mounted on massive aluminum extrusions and dissipates heat via an extremely quiet and effective two-speed fan. PV amplifiers are designed to operate at line voltages as low as 50% of nominal, employing mammoth toroidal power transformers and offering impressive specifications and features not found on similarly priced competitive unit\'s. This amp is designed to drive a 2-Ohm load per channel, thus achieving awesome performance levels into 4 Ohms in BRIDGE mode. PV amplifiers are ruggedly constructed, rack-mountable pieces of gear with superb patching capability, allowing superior flexibility in application. Front panel features include calibrated, detented gain (dB) controls and LED indicators for power (PWR), signal presence (SIG), Thermal Protection indicator, and DDT activation on each channel, as well as a rocker mains POWER switch. The back panel contains an IEC connector, line voltage selector switch, dual primary fuses, and the critical cooling fan opening. This opening should have an adequate supply of cool air and should never be blocked or restricted. Also on the back panel are the input and output sections, including an input barrier strip for permanent installations. Each channel input section includes a combo XLR / TRS phone jack connector, THRU/LOW out and HIGH out TRS jacks, and activation switches for the LOW CUT filter and crossover (150 Hz XOVER). Channel output sections feature dual shock-proof binding posts and four-conductor twist lock connectors. An additional four-conductor twist lock connector allows BRIDGE mode output. |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 300 Watt rms | | Power output stereo 8Ω: | 2 x 180 Watt rms | | Power output bridged 8Ω: | 600 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 6 A | | Power Consumption: | 1300 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 470 / 18.05 mm/inch | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series power amps combine excellent audio performance, modern and innovative circuit design, meticulous and exceptionally rigid construction, and the highest levels of operational integrity and reliability with an appropriate and more than realistic price. The robust steel chassis provides outstanding torsional strength through L-shaped side panels reaching under the thick aluminium front panel. Thermal breakers prevent the power supply units from being damaged by thermal overload. Electronically controlled fans provide sufficient front-to-rear airflow and a special cool air diverter takes care of thermal stability. The fans? noise-level is extremely low which provides the possibility for studio use. If necessary, a supplied air-filter can be mounted behind the front panel ventilation louvres. Features * Excellent audio performance * Symmetrical topology * Ultra-low distortion * Generously dimensioned power supply units * Suitable to be operated on loads down to 2 ohms * Suitable to drive complex loads with phase angles of ± 90 degree * Extensive protection circuitry * Unique Back-EMF protection * Switchable limiters * Switchable Hi/Lo-Cut filters * Robust steel chassis * Exceptional low noise front-to-rear air-flow * XLR-type inputs and direct-outs * LED display shows On, In, Out, Limit and Protect * Highly reliable operation
Specs * Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0% * Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0% * Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0% * Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0% * Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0% * Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 % * Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz * Phase Angle Response : ± 30 degree/20 Hz.....20 kHz * Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1% * Voltage Gain ref. 1 kHz : 26 dB (constant gain option) * Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz * Maximum Input Level : +21 dBu / 8.7 V * Input Impedance active balanced : 20 kohms * THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz * IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output * Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms, A-weighted, RMS, input sensitivity +6 dBu * Attenuation at rated output : > 70 dB f = 1 kHz * Damping Factor internal 1 kHz : > 300 * DIM 30 : < 0.01 % * DIM 100 : < 0.01 % * Slew Rate internal : > 25 V / ?s * Power Consumption : 300 W 1/8 rated output into 4 ohms * Width : 483 mm * Height : 88.1 mm * Depth : 426 mm * Weight : 14 kg |
Power Output Level R-150 PLUS
STEREO
8ohm(T.H.D 0.05%) 50W+50W
4ohm(T.H.D 0.05%) 75W+75W
BRIDGED MONO
8ohm(T.H.D 0.05%) 50W
8ohm(T.H.D 0.5%) 170W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
- 2Χ350W 8Ω 2x500W 4Ω 2x650W STEREO MODE
- BRIDGE 2000W 4 Ω
- 16Kg
- 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
- Precise Power, Signal and Clip LEDs to monitor performance
- XLR and 1/4" TRS input connectors for compatibility with any source
- Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
- Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
- Independent limiters per channel offer reliable protection against overload and distortion
- High-current toroidal transformer for ultra-high transient response and absolute reliability
- Ultra-reliable Toshiba/Fairchild power transistors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front” ventilation system including air filter for reliable operation
- “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements in reliability, flexibility and sound. Alone or in combination with the other products of the Bittner portfolio. The consequent realisation of the Bittner quality standards indicates once more our understanding of the contracting business. It underlines our philosophy that cost consciousness has nothing to do with giving up standards. Compromise is a word unknown to Bittner Audio! The incorporation of detent potentiometers, clip limiter, protection circuits for any imaginable situation, as well as a first-class production process using only highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay XLR Inputs Speakon and Binding Posts Clip Limiter Toroidal transformers LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed, low noise fans Detent potentiometers Stereo / Bridged / Parallel Mode Ground Lift Robust Steel Chassis 3 Year Warranty
TECHNICAL DATA: Basic 400: 2x 200 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.03% Signal-to-Noise Ratio: < -102 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: > 400 @ 4 Ohm Cooling: 2x Fan (temp. reg. variable speed) Weight: 12 kg. Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“) |
Reviews
There are no reviews yet.