| Content | The new HP4 from PreSonus answers the need for a headphone distribution
amplifier with professional specifications in a small package at an affordable
price. The HP4 features four discrete headphone outputs on the front panel
each with its own volume potentiometer and 150mW of amplification per channel.
The HP4 also features adjustment over control room monitors with a separate
volume control, monitor mute switch and mono switch giving you an extremely
powerful monitoring solution at an amazingly low price.
Features
? Four High Power Headphone Outputs
? Ultra loud (150mW per channel)
? Ultra quiet operation
? Musical Wide Dynamic Range
? Control Room Monitor Outputs with Level Control
? Mono or Stereo Operation
? Monitor Mute Switch
? Daisy Chain an Infinite Number of Units
? Compact package
Technical Specifications
Input
TRS Impedance 10K Ohms
Panel Controls
Headphone Level 1 to 12
Monitor / Feed Output -80dB to +10dB
Mono Switch
Monitor / Feed Mute
Power Supply
Type Linear
Input 16VAC/1000mA
Output
TRS Balanced 51 Ohms Impedance
Performance
THD+Noise (Unweighted) 0.002%
Noise Floor -98dB
Signal To Noise >95dB
Power Supply Rejection >98dB
Power 16 Watts
Physical
Weight 5lbs./ 2.3 kg.
Dimensions 5.5 x 5.5 x 1.75
Mounting Max Rack and Universal Rack Tray
Chassis Steel
Panel Brushed Aluminum
Sides Cast Aluminum |
Overview
With Sennheiserʼs HDVD 800, sound is perfect. The HDVD 800 is able to connect with digital sources and is equipped with a high-quality Burr-Brown digital/analog converter (DAC) that converts digital audio data into analog signals with a resolution of 24 bits and a sampling rate of up to 192 kHz. This enables the HDVD 800 to transmit the entire frequency spectrum of high-end audio sources without any loss of frequencies.
In addition to the symmetrical inputs, the HDVD 800 also has an asymmetrical input socket; incoming signals are symmetrized before further processing takes place. Digital sources can be connected to the rear of the unit via an XLR (AES/EBU) input, optical and coaxial (S/PDIF) digital inputs or USB. All digital inputs accept signals up to 24 bit at 192 KHz*. Designed and manufactured in Germany, this high-end, solid-state amplifier harmonize perfectly and deliver an ultimate acoustic performance when paired with any of Sennheiserʼs audiophile headphones.
Features
D/A transducer for all common formats up to 24 bit / 192 kHz
D/A transducer can be used for CD and DVD players
AES/BU, S/PDIF, USB inputs
Symmetrical (XLR) and asymmetrical (RCA) analog inputs
Symmetrical output
Sockets for four sets of headphones (two of which symmetrical)
|
Plug In, Rock Out with the Joe Satriani amPlug headphone amp
The Joe Satriani signature model is the latest addition to our incredibly popular amPlug series of headphone guitar amps!
- Joe's signature lead tone with your choice of delay on or off
- Distortion tone with superb dynamic response, inspired by the Satchurator
- Analog-style delay with Joe's filter & EQ, inherited from the Time Machine
- Plugs straight into your electric guitar, so you can instantly enjoy great sound through your headphones
- Convenient and portable with up to 11 hours of battery operation
- AUX input jack lets you jam along to tunes on your CD/MP3 player
The amPlug series of palm-sized headphone guitar amps make it easy to enjoy great guitar/bass sounds at home, in your room, or anywhere. This lineup is now joined by the amPlug Joe Satriani signature model, which borrows freely from the VOX/Joe Satriani line of signature pedal effects.
Specifications -
Power supply: AAA batteries (x 2)
-
Battery life (FX on):
Zinc-carbon batteries: approximately 3 hours
Alkaline batteries: approximately 11 hours
-
Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22"
-
Weight: 40 g/1.41 oz. (not including batteries)
-
Included items: Two AAA batteries (for verifying operation)
|
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
|
HeadAMP - Four Output Stereo Headphone Amp Overview
Most home recordings involve from one to four people, any or all of whom are
going to need headphone monitoring. The monitor amp would be connected
to the tape deck?s headphone output or a mixer output so that the performers
can hear themselves and each other. Of course the same application can apply
to band rehearsals and even home entertainment. HeadAMP provides amplification
and individual volume control for up to 4 headsets. It can be driven by either line-
level or headphone amplifier signals (mono or stereo).
HeadAMP - Four Output Stereo Headphone Amp Specifications:
Signal To Noise Ratio >90dB
IMD (SMPTE) 0.01%
Maximum Input Level +14dBV
Maximum Output Level 20dB per channel
Output Impedance 51 Ohms per channel
Output Connectors Four stereo 1/4? headphone outputs
Power Requirements 12V DC (Adapter included)
Total Harmonic Distortion |
- All-passive volume control circuit
- Stereo and AUX inputs
- Dual outputs
- Additional mono output
- Balanced and unbalanced connection
- Integrated high quality headphone amplifier
- Mono, mute and PFL switches
- Stereo volume, AUX and headphone level controls
- Elegant design with solid wood side panels
- Built to last
The Palmer Monicon® L is a precise, analogue volume control that connects between a computer or audio interface and active monitor speakers. The switch is completely passive and distortion-free, the LED displays and built-in headphone amplifier are powered via the included power supply.
Symmetric combo sockets serve as stereo input. The Monicon® L’s AUX input features RCA sockets and a 3.5 mm stereo jack. The compact console offers outputs for two monitor pairs and a mono summed output via XLR sockets. The stereo or AUX input can be selected alternately, the two outputs individually and together. In addition to its large volume controller, the Monicon® L is also equipped with mono, mute and PFL switches, a 6.35 mm headphone output, and separate AUX and headphone controllers for convenient operation.
Product type
Other Studio and Recording Equipment
Channels
2
Inputs
2
Input connectors
3.5 mm TRS , RCA , XLR
Input type
balanced/unbalanced (depending on TS/TRS connection)
Max. input level
20 dBu
Input impedance
(balanced) 10k Ohm(s) , (unbalanced) 5k Ohm(s)
Outputs
3
Output connectors
XLR
Output type
balanced/unbalanced (depending on TS/TRS connection)
Max. output level
20 dBu
Output impedance
600 Ohm(s)
Frequency response
10 - 40000 Hz
THD
0.001 %
Max. attenuation
(Attenuator + Mute) 112 dB , (Attenuator) 85 dB
Controls
attenuation , input selector , mono , mute , output selector , PFL source
Cabinet material
sheet steel , wood
Cabinet surface
Powder coated
Width
218 mm
Height
77 mm
Depth
100 mm
Weight
1,14 kg |
Reviews
There are no reviews yet.