| Content |
System type : 2-way vented enclosure
Nominal Impedance : 8 ohm
Input power rating (continuous) : 600 W
Input power rating (peak) : 1200 W
Frequency response : 55Hz - 18kHz (-6dB, +6dB)
Sensitivity : 101dB @ 1W/1m
Maximum (peak) Output : 131 dB @ 1m
Low Frequency Device : 2 x 12'' woofer - 3'' voice coil
High Frequency Device : 1.4'' throat - 3'' titanium voice coil
Coverage Angle H. (-6 dB) : 70¡Æ
Coverage Angle V. (-6 dB) : 70¡Æ
Trapezoidal taper : 10¡Æ
Monitor Taper : 40¡Æ
Crossover Frequency : 1800 Hz
Signal Processing : Proel DSO26 (biamp mode)
Flying System : 4 x M10 - top, bottom, rear
Connectors : 2 x SPK4MP linked
Construction : 18mm birch plywood
Finishing : Anti-scratch coating
Cabinet Colour : Black
Mounting Hole : 1 x bottom
Weight : 32 kg (70.560 lb)
Dimensions (W x H x D) : 40 x 87.5 x 43 cm
|
Features
* DVX3121 12" LF Transducer with forced air cooling
* ND2 2" Voice Coil, 1" Exit Neodymium CompressionDriver
* 60° x 60° Coverage Pattern
* 600W Continuous (2400W peak) power handling
* High sensitivity, 131 dB maximum SPL
* Adjustable monitor angle (45° or 55°)
* 2 Anchor plates for single stud fittings and 7integral suspension points
* Available in black or white
* Passive/biamp selectable
* Full line of accessories
Specifications
* Frequency Response (-3dB): 58Hz-15kHz
* Frequency Range (-10dB): 48Hz-20kHz
* Rec. Hipass Frequency: 50Hz
* Axial Sensitivity: 97dB (1W/1m)
* Max. Calculated SPL: 131 dB
* Horizontal Coverage: 60°
* Vertical Coverage: 60°
* Power Handling (Passive): 600W continuous, 1200Wprogram, 2400W peak
* LF Power Handling (Biamp): 500W continuous, 1000Wprogram, 2000W peak
* HF Power Handling (Biamp): 40W continuous, 80Wprogram, 160W peak
* LF Transducer: DVX3121, 12" driver
* HF Transducer: ND2, 1" exit Neodymium compressiondriver
* Crossover Frequency: 2kHz
* Nominal Impedance: 8 ohms
* Minimum Impedance: 6.2 ohms
* Connectors: (2) Neutrik Speakon NL4\'s
* Enclosure Material: Polypropylene structural foam
* Suspension: Enclosure has locations for 4 single-studattachment plates and10 forged steel eyebolts - 2 on top, 2 on bottom, 2 onside, and 1 on rear ofenclosure
* Grille: Polyester powder coated, 16GA Galvanizedsteel, with rotatable logo
* Dimensions (H x W x D): 24.14" x 15.64" x 14.26“
* Net Weight: 43.7 lbs
* Shipping Weight: 48.6 lbs | The Electro-Voice® ZX3 offers an unprecedented level of lightweight, 12-inch, two-way, loudspeaker performance for the widest variety of portable and installed applications. Featuring the new DVX3121 12-inch woofer and the ND2 neodymium compression driver, the ZX3 continues the groundbreaking innovation of the EV DVX woofer program, joining the ranks of EV\'s ZX series between the eight-inch ZX1 and the 15-inch ZX5.
When it comes to problem and solution versatility, the ZX3 is in a class of its own. In addition to the highest performance drivers available, a complete range of optional accessories, including the CB-5 array kit, MB3 wall and ceiling-mount bracket, HA-3 handle adapter for use with the VSA-1 strong arm mount, and TCA-1 truss clamp adapter allow the ZX3 to be easily and precisely configured in multiple box arrays, mounted on trusses or tripods, deployed as monitors, or used as system mains with a subwoofer.
Housed in a stylish yet rugged injection molded enclosure, the ZX3 shares the same functionality as the larger ZX5, with 90 degre x 50 degree or 60 degree x 60 degree horn dispersion patterns, 45 degree or 55 degree monitor angles, passive or biamp operation, and seven M8 rigging points. The ZX3 is available in a weatherized version and in either a black or white finish. An optional HDC-3 heavy-duty stackable cover is also available. |
The MI-112 is a 2-way passive full range loudspeaker that utilizes a 12? cone
low frequency transducer and a 1? throat compression driver with titanium
diaphragm. The multi-angle cabinet is constructed of Complex Aggregate Board
and finished with a hard-wearing black carpet. Two bar handles and a steel grille
sealed against corrosion using a polyamide powder coat finish are provided. A 35
mm tripod socket allows for stand mounting.
APPLICATIONS:
Intended for use in portable sound reinforcement and P.A.
FEATURES:
2-way vented loudspeaker system
1 x 12" speaker
1" compression driver with constant directivity horn
225 W power handling
Highly resistant CAB enclosure
SPECIFICATIONS:
RMS (Average) Power HandlingR: 225 W
Program Power HandlingP: 450 W
Peak Power HandlingK: 900 W
On-axis Frequency RangeF: 60 Hz - 16 kHz
Nominal Impedance: 8 Ω
On-axis Sensitivity 1W / 1 mS: 98 dB SPL
Rated Peak SPL at Full Power:128 dB
Nominal -6 dB BeamwidthsB: 90° Horizontal
(average, 500 Hz to 8 kHz) 75° Vertical
Speech Coverage AnglesC: 90° Horizontal x 80° Vertical
Enclosure Material:Complex Aggregate Board
Finish:Blue Gray carpet
Connector: 2 paralleled NL4 Speakon, wired
Dimensions (H x W x D): 59 x 43 x 35 cm / 26.5 x 19 x 15.4 in
Weight: 20.3 kg/ 45 lbs
Shipping Weight: 23.5 kg/ 52 lbs |
With the newly designed D12W, DYNACORD fulfills a longtime customer demand for a light-weight , extremely robust highperformance professional 12" 2-way plastic cabinet for use in professional, portable and fixed install sound reinforcement applications.
With a variety of suspension accessories and conservative cosmetics, the D12 is ideally suited to be used in demanding fixed installations. The cabinet is manufactured from Polypropylene and therefore is extremely resistant against abuse on the road.
For low frequencies an Electro-Voice DL12BFH is used. The recently developed Electro-Voice ND2 Neodymium driver is used for the projection of mid and high frequencies. The Constant- Direcctivity HF horn has been integrated into the baffle by CAD methods.Nominal coverage angle of the cabinet is 80°*40°, horizontal*vertical respectively. Power handling of the cabinet is 300W (continuous) and 1200W peak.. Maximum sound pressure level is 129dB, the frequency range of the D12 is 70Hz to 18kHz. The D12 is ideally suited for applications as full-range cabinet or as Mid-Hi cabinet in in highperformance small-format active and passive satellite systems.
|
Electro-Voice TX1122 Tour-X 2-Way 12" PA Speaker
The Electro-Voice TX1122 is a high power, 2-way loudspeaker system that can be used in a variety of applications where high-quality sound reinforcement is required in a lightweight package.
It utilizes the DH3, high output 1.25" titanium compression driver, coupled to a constant directivity 90 degree x 50 degree horn. This combination results in a smooth response to 20 kHz and excellent pattern control in short to medium throw applications.
The SMX2120 12" woofer has an FEA optimized magnet structure for very low distortion and maximum intelligibility at high SPL levels. The crossover uses steep 24dB/octave slopes with equalization for very smooth response in vocal range, extended HF, and a protection circuit for long-term reliability.
It has a variety of features that make it equally suited for portable or fixed installation applications. The trapezoidal enclosure is constructed out of a combination of plywood and MDF, and coated with EVCoat for maximum strength while still remaining lightweight. The unique grille design is very strong, dent resistant, and features a rotatable logo. Four-way handles allow for gripping in a variety of positions, a pole mount allows for placement on a subwoofer or a tripod. Six 3/8" threaded points allow a single TX1122 to be suspended in a various positions. The recessed input panel with dual NL4 connectors keeps the connectors hidden, while allowing it to be used with the TX1181 subwoofer for extended sub bass on a single amplifier channel, with no additional processing needed.
Order today with the no-risk assurance of our Total Satisfaction and Low Price Guarantees!
- Freq. response (-3 dB): 60Hz - 20kHz
- Freq. range (-10 dB): 45Hz - 20kHz
- Rec. Hi-pass frequency: 45Hz
- Axial sensitivity: 97dB (1W/1m)
- Max. calculated SPL: 130dB
- Horizontal coverage: 90 degree
- Vertical coverage: 50 degree
- Power handling: 500W continuous, 2000W peak
- LF transducer: SMX2120, 12" (305mm) driver
- HF transducer: DH3, 1.25" (32mm) diaphragm compression driver
- Crossover frequency: 1750Hz
- Nominal impedance: 8 Ohms
- Minimum impedance: 5.4 Ohms
- Connectors: (2) Neutrik Speakon NL4\'s
- Enclosure material: plywood and MDF with EVCoat
- Grille: 16 GA steel, black powdercoat, with rotatable logo
- Suspension: (6) 3/8" threaded points - (2) on each side and (2) on the rear of enclosure
- Dimensions (H x W x D): 24.3" x 15.0" x 15.0" (616mm x 382mm x 380mm)
- Net weight: 44.5lbs (20.2 kg)
- Shipping weight: 50.0lbs (22.7 kg)
|
Reviews
There are no reviews yet.