| Content |
The new RODE NTG-1 is a lightweight condenser shotgun microphone, specifically
designed for professional applications within the film, video, television, voice-over and
ENG industries.
The NTG-1 provides an electronically balanced output stage and operates on 48 V to
the P48 standard. The NTG-1 offers wide bandwidth and a controlled polar response
coupled with low noise SMT electronics. The NTG-1 is extremely lightweight making it
ideal for mounting directly to video cameras (with optional accessories) or a Boom pole.
The NTG-1 comes complete with mount and windshield. The supplied windscreen effectively
suppresses wind noise when recording outdoors in moderate conditions. Optional accessories
are available for more demanding applications.
SPECIFICATIONS:
Features:
Broadcast sound quality. Low noise circuitry. Condenser transducer. Rugged metal construction.
Low weight: 105 grams approx. . Low handling noise. Supplied with stand mount, zip pouch and
windshield. Designed & manufactured in Australia. Full 2 year guarantee.
Operation power:
The NTG-1 is designed to operate from standard P48 phantom power. The NTG-1 will
operate between 44 V to 52 V applied with positive polarity to pin 2 and pin 3 via the
output XLR connector.
Operation output impedance:
The NTG-1 will operate satisfactorily into a load impedance as low as 1 k§?. If a load below
this is used, the output signal level will be reduced. The NTG-1??s output is balanced between
pin 2 (hot), pin 3 (cold) and pin 1 is ground.
Acoustic principle: Line plus Gradient.
Directional pattern: Super-Cardioid.
Frequency range:
20 Hz ~ 20 kHz selectable HPF @ 80 Hz/12 dB octave
Output impedance: 50 ?
Signal noise ratio din iec 651:
76 dB (1 kHz rel. 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 18 dB SPL (per IEC651, IEC268-15)
Maximum spl: 139 dB (@ 1% THD into 1 k?)
Sensitivity:
-36 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 121 dB (per IEC651, IEC268-15)
Power supply voltage: P48 Phantom, 44 V to 52 V
Current consumption: 3.5 mA
Output connection:
3 pin XLR, balanced output between pin 2 (+), pin 3 (-) and pin 1 (ground)
Weight with battery: 105 g approx.
Dimensions width: 217mm
Dimensions depth: 22mm
Dimensions height: 22mm
|
Designed for video production and broadcast (ENG/EFP) audio acquisition, the AT8015 provides the narrow acceptance angle desirable for long-distance sound pickup, along with excellent sound rejection from the sides and rear of mic. The roll-off position reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations.
Designed for video production and broadcast (ENG/EFP) audio acquisition
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 40-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -38 dB (12.5 mV) re 1V at 1 Pa Battery: -39 dB (11.2 mV) re 1V at 1 Pa
Impedance: Phantom: 250 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 110 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off
Weight: 195 g (6.9 oz)
Dimensions: 460.0 mm (18.11“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8135 windscreen; battery; protective carrying case
| Broadcast sound quality
Low noise circuitry
Internal rechargeable lithium battery, supplying over 150 hours operation
Fully charged in under two hours via MicroUSB
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
MicroUSB cable included
Ten year extended warranty with online registration
Building on the popularity and acceptance of the RØDE NTG2, the NTG4+ features an all-new condenser capsule with low noise, high sensitivity and the convenience of on-board equalisation/level control via digital switching.
The NTG4+ is the very first microphone to feature an in-built battery that provides 150+ hours of operation with the convenience of USB charging.
Visit the NTG4+ feature page
NTG4+ Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom powerInternal battery
Weight 176gm
Dimensions 278mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration |
For when you need even more advanced recording than R-09's built-in mic
CS-15CS-15 For serious field recording, the optional CS-15 cardioid-type stereo microphone is a great match for the R-09. For portability and convenience, the R-09 supplies the power to the mic. Bundled with the microphone are a desktop stand, a hand-held mount, and a windscreen.
Cardioid-type stereo microphone
Battery operation is also possible when using with a recorder that doesn't supply the power
Ideal combination with the R-09 --- also the UA-4FX and the UA-1EX
Comes with a desktop stand, a hand-held mount (can be attached to the microphone stand) and a windscreen | The RØDE VideoMic is a professional grade 1/2" condenser shotgun microphone designed for use with consumer video cameras and personal audio recorders.
The integrated shock mounting system isolates the VideoMic capsule and electronics from its all-metal shoe mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone.
Its standard sized shoe mount also includes a 3/8" thread in the base for easy mounting on a boom pole or stand. (note that cameras with proprietary sized mounts require an additional adaptor.)
Its super cardioid polar pattern is highly directional, focusing on the subject in front of the camera, and minimising any surrounding sounds.
In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
A -10dB and -20dB level attenuation (or PAD), selectable from inside the battery compartment, allows recording of loud sound sources, such as live music or motorsport.
The RØDE VideoMic directional on-camera microphone is covered by RØDE Microphones' industry leading 10 year warranty.
| Frequency response |
40Hz-20kHz, selectable HPF @ 80Hz/12dB/octave |
| Sensitivity |
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Ιmpedance |
200Ω |
| Τotal harmonic distortion |
134dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Dimensions |
250mm x 65mmx 102mm |
| Weight |
176gm |
|
The new RODE NTG-2 is a lightweight condenser shotgun microphone, designed
for professional applications within the film, video, television and production industries.
The NTG-2 provides a balanced low impedance output stage and operates either
from an internal 1.5 V battery (AA) or 48 V to the P48 standard. A wide bandwidth
and controlled polar response coupled with low noise SMT electronics, makes the
NTG-2 the perfect choice for film, video engineering and voice-over work. The NTG-2
is extremely lightweight making it ideal for mounting directly to video cameras or on
boom poles.
The NTG-2 comes complete with mount and windshield.The windscreen effectively
suppresses wind noise when recording outdoors in moderate conditions.
SPECIFICATIONS:
Features:
Broadcast sound quality. Rugged metal construction. Condenser microphone transducer.
Weighing 161 grams approx. . Low noise circuitry. Low handling noise. Supplied with stand
mount and zip pouch. Designed & manufactured in Australia. Full 2 year guarantee.
Operation power:
The NTG-2 is designed to operate from standard P48 phantom power or a 1.5 V Alkaline Battery.
The NTG-2 will operate between 44 V to 52 V applied with positive polarity to pin 2 and pin 3 via
the output XLR connector.
Operation output impedance:
The NTG-2 will operate satisfactorily into a load impedance as low as 1 k§?. If a
load below this is used, the output signal level will be reduced. The NTG-2??s
output is balanced between pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Line plus Gradient.
Directional pattern: Super-Cardioid.
Frequency range:
20 Hz ~ 20 kHz selectable HPF @ 80 Hz/12 dB octave
Output impedance: 250 ? - phantom power, 350 ? - battery power
Signal noise ratio din iec 651:
76 dB (1 kHz rel. 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 18 dB SPL (per IEC651, IEC268-15)
Maximum spl: 131 dB (@ 1% THD into 1 k?)
Sensitivity:
-36 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 113 dB (per IEC651, IEC268-15)
Power supply voltage: 1.5 V Alkaline Battery or P48 Phantom
Current consumption: 2.0 mA
Battery life: >400 hours with fresh alkaline battery.
Output connection:
3 pin XLR, balanced output between pin 2(+), 3(-) and Pin 1 (ground)
Weight with battery: 161 g approx.
Dimensions width: 278 mm
Dimensions depth: 22mm
Dimensions height: 22mm
|
Reviews
There are no reviews yet.