NT2-A – ?The Legend Continues? Multi Pattern 1? Condenser Microphone. The new NT2-A carries on the tradition forged by the now legendary R?DE NT2. A professional large capsule (1?) studio microphone incorporating three-position pick-up patterns, pad and high pass filter switches conveniently located on the mic body. At the heart of the NT2-A is […]
NT2-A – ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) – pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm
Weight
2.90 kg
Reviews
There are no reviews yet.
Be the first to review “RODE NT-2A Multipattern Condenser Microphone” Cancel reply
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm
Acoustical operating principle
Pressure gradient transducer
Directional pattern
Cardioid
Frequency range
20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm
13 mV/Pa
Rated impedance
50 ohms
Rated load impedance
1000 ohms
Equivalent noise level, CCIR1)
23 dB
Equivalent noise level, A-weighted1)
12 dB-A
Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL)
71 dB
Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL)
82 dB
Maximum SPL for THD
110 dB
Maximum SPL for THD
129 dB
Maximum output voltage for THD
-1 dBu
Dyn. range of the mic. amplifier /A-weighted, 0.5 %2))
98 dB
Dyn. range of the mic. amplifier /A-weighted, 5 %2))
117 dB
Supply voltage (P48, IEC 61938)
48 V ± 4 V
Current consumption (P48, IEC 61938)
3.2 mA
Matching connector
XLR 3F
Weight
825 g
Diameter
78 mm
Length
165 mm
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal
The RODE NT1-A has become an industry standard; delivering the warmth, extended dynamic range, clarity and high SPL capability usually only featured by some of the most expensive microphones.
Now available as the \'Complete Vocal Recording Solution\' this NT1-A package now includes everything you need to get truly professional vocal recordings - the world\'s quietest studio microphone, a studio grade pop shield and shock mount, a premium 20\' cable, dust cover, an instructional DVD with recording tips, and of course R DE\'s industry leading ten year warranty.
Large 1" (25mm) capsule with gold plated diaphragm
Cardioid polar pattern
Self noise of only 5dB (A)
Ultra low noise, transformerless surface mount circuitry
Dynamic range of the microphone amplifier DIN/IEC 651
130 dB
Supply voltage
48 V ± 4 V
Current consumption
3 mA
Matching connectors
XLR 3F
Weight
480 g
Diameter
49 mm
Length
175 mm
Acoustical operating principle
Pressure transducer
Directional pattern
Omnidirectional
Frequency range
20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm
20 mV/Pa
Rated impedance
50 ohms
Rated load impedance
1000 ohms
Equivalent SPL CCIR 468-3
28 dB
Equivalent SPL DIN/IEC 651
15 dB-A
S/N ratio CCIR 468-3
66 dB
S/N ratio DIN/IEC 651
79 dB
Max. SPL (tube characteristic)
K
Dynamic range (of the amplifier)
K
Maximum output voltage
8 dBu
Weight
800 g
Diameter
78 mm
Length
165 mm
* THD of the microphone amplifier at an input voltage which is equivalent to the capsule output voltage at the specified SPL.
The AVANTONE CK-6 is truly a gorgeous looking and sounding microphone. The design, character and performance can be compared directly to fine studio-standard FET mics…but at a fraction of their cost!
The rugged CK-6 microphone body and capsule assembly are precision machined of Brass. Aesthetically the compact body features an elegant Metallic Cabernet Wine-Red finish, accented with polished nickel trim and capsule assembly. Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability.
This Transformerless CLASS A FET Microphone w/ 32mm gold sputtered thin Mylar capsule is designed with circuitry that will yield pleasing professional results comparable to much more expensive designs. It also features -10 dB pad & 80 Hz LF roll off switches for varied recording situations.
The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.
Applications
Studio vocals, acoustic guitar, mandolin, drum overheads, piano, etc…
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.