Content |
RODE VideoMic Pro Rycote
- All new capsule with lower noise and higher sensitivity
- Compact form factor (150mm)
- 9V battery powered - over 70 hours use (alkaline)
- Integrated foam windscreen
- Two step High Pass Filter (flat, 80Hz)
- Camera shoe mount with 3/8" thread for easy boompole mounting
- Rycote Lyre shock mounting onboard
- Broadcast recording quality condenser microphone
- Ultra lightweight (85g)
- Integrated shock mounting
- 3.5mm stereo mini-jack output (dual mono)
- Three position level control (-10dB, 0, +20dB)
- 10 year warranty with online registration at www.rodemic.com/warranty
|
Designed for video production and broadcast (ENG/EFP) audio acquisition, the AT8015 provides the narrow acceptance angle desirable for long-distance sound pickup, along with excellent sound rejection from the sides and rear of mic. The roll-off position reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations.
Designed for video production and broadcast (ENG/EFP) audio acquisition
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 40-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -38 dB (12.5 mV) re 1V at 1 Pa Battery: -39 dB (11.2 mV) re 1V at 1 Pa
Impedance: Phantom: 250 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 110 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off
Weight: 195 g (6.9 oz)
Dimensions: 460.0 mm (18.11“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8135 windscreen; battery; protective carrying case
|
Element: Externally polarized (DC bias) capacitor
Polar Pattern: Line + gradient
Frequency Response: 20-18,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: -29 dB (35.5 mV) re 1V at 1 Pa
Impedance: 50 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad (nominal)
Dynamic Range: 128 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 81 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 48V DC, 4.8 mA typical
Weight: 175 g (6.2 oz)
Dimensions: 539.0 mm (21.22“) long, 21.0 mm (0.83“) maximum body diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8147 windscreen; two O-Rings; protective carrying case
|
The new RODE NTG-1 is a lightweight condenser shotgun microphone, specifically
designed for professional applications within the film, video, television, voice-over and
ENG industries.
The NTG-1 provides an electronically balanced output stage and operates on 48 V to
the P48 standard. The NTG-1 offers wide bandwidth and a controlled polar response
coupled with low noise SMT electronics. The NTG-1 is extremely lightweight making it
ideal for mounting directly to video cameras (with optional accessories) or a Boom pole.
The NTG-1 comes complete with mount and windshield. The supplied windscreen effectively
suppresses wind noise when recording outdoors in moderate conditions. Optional accessories
are available for more demanding applications.
SPECIFICATIONS:
Features:
Broadcast sound quality. Low noise circuitry. Condenser transducer. Rugged metal construction.
Low weight: 105 grams approx. . Low handling noise. Supplied with stand mount, zip pouch and
windshield. Designed & manufactured in Australia. Full 2 year guarantee.
Operation power:
The NTG-1 is designed to operate from standard P48 phantom power. The NTG-1 will
operate between 44 V to 52 V applied with positive polarity to pin 2 and pin 3 via the
output XLR connector.
Operation output impedance:
The NTG-1 will operate satisfactorily into a load impedance as low as 1 k§?. If a load below
this is used, the output signal level will be reduced. The NTG-1??s output is balanced between
pin 2 (hot), pin 3 (cold) and pin 1 is ground.
Acoustic principle: Line plus Gradient.
Directional pattern: Super-Cardioid.
Frequency range:
20 Hz ~ 20 kHz selectable HPF @ 80 Hz/12 dB octave
Output impedance: 50 ?
Signal noise ratio din iec 651:
76 dB (1 kHz rel. 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 18 dB SPL (per IEC651, IEC268-15)
Maximum spl: 139 dB (@ 1% THD into 1 k?)
Sensitivity:
-36 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 121 dB (per IEC651, IEC268-15)
Power supply voltage: P48 Phantom, 44 V to 52 V
Current consumption: 3.5 mA
Output connection:
3 pin XLR, balanced output between pin 2 (+), pin 3 (-) and pin 1 (ground)
Weight with battery: 105 g approx.
Dimensions width: 217mm
Dimensions depth: 22mm
Dimensions height: 22mm
|
With an overall length of just 9.17" and weight of just 3.5 oz, this microphone adds virtually no heft to the end of a fish pole or the top of a minicam. Through the use of an innovative Audio-Technica design, the interference tube of the BP4073 provides a narrow acceptance angle, effective for long-distance pickup. The highly directional mics offer low self-noise and are fully RoHS-compliant - free from all substances specified in the EU directive on the reduction of hazardous substances (RoHS).
Designed for use in broadcasting, film/TV production and theater sound reinforcement applications
Direct-coupled, balanced output ensures a clean signal even in high-output conditions
Innovative acoustic design provides same directivity as mics up to 50% longer
Switchable 80 Hz hi-pass filter & 10 dB pad
Rugged housing made of lightweight structural-grade aluminum alloy
RoHS-compliant - free from all substances specified in the EU directive on the reduction of hazardous substances (RoHS)
Element: Externally polarized (DC bias) capacitor
Polar Pattern: Line + gradient
Frequency Response: 20-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: -29 dB (35.5 mV) re 1V at 1 Pa
Impedance: 50 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad (nominal)
Dynamic Range: 128 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 81 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 48V DC, 4.8 mA typical
Weight: 99 g (3.5 oz)
Dimensions: 233.0 mm (9.17“) long, 21.0 mm (0.83“) maximum body diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8144 windscreen; two O-Rings; protective carrying case
| The RØDE VideoMic is a professional grade 1/2" condenser shotgun microphone designed for use with consumer video cameras and personal audio recorders.
The integrated shock mounting system isolates the VideoMic capsule and electronics from its all-metal shoe mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone.
Its standard sized shoe mount also includes a 3/8" thread in the base for easy mounting on a boom pole or stand. (note that cameras with proprietary sized mounts require an additional adaptor.)
Its super cardioid polar pattern is highly directional, focusing on the subject in front of the camera, and minimising any surrounding sounds.
In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
A -10dB and -20dB level attenuation (or PAD), selectable from inside the battery compartment, allows recording of loud sound sources, such as live music or motorsport.
The RØDE VideoMic directional on-camera microphone is covered by RØDE Microphones' industry leading 10 year warranty.
Frequency response |
40Hz-20kHz, selectable HPF @ 80Hz/12dB/octave |
Sensitivity |
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
Ιmpedance |
200Ω |
Τotal harmonic distortion |
134dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
Dimensions |
250mm x 65mmx 102mm |
Weight |
176gm |
|
Reviews
There are no reviews yet.