| Content |
An elegant solution for personal monitoring on stage or in the studio.
FEATURES:
XLR microphone input
XLR microphone Thru, microphone output to send to main mixer
1/4" stereo mix input
1/4" stereo mix Thru for daisy chaining additional units
Microphone volume control
Mix volume control
Two headphone outputs
18 Volt AC adapter included
|
The amPlug Night Train perfectly simulates the high-gain sound of the compact VOX Night Train tube amp. Just as with the actual Night Train head, you can switch between the two preamp sounds. The BRIGHT position boosts the high-frequency range; the THICK position offers a chunkier, heavier sound. The emulated speaker cabinet circuit accurately recreates the sound of the Night Train amp being played through the matching V112NT single 12" Night Train speaker cabinet. As a finishing touch, amPlug Night Train share some of the cool looks of its namesake amplifier.
Specifications - Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
- Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
- Power supply: AAA batteries (x 2)
- Battery life: amPlug Night Train:
- With zinc-carbon batteries: approximately 9 hours
- With alkaline batteries: approximately 24 hours
- Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
- Weight: 40 g/1.41 oz. (not including batteries)
- Included items: AAA batteries (X2) (for verifying operation)
|
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
| Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
| The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped.
In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation.
A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback.
The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
- Model Name: LDHPA1
- Product Type: headphone amplifier
- Type: 1-channel stereo
- Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
- Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
- Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
- Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
- Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
- Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
- Headphone Outputs: 1
- Headphone Output Connectors: 3.5 mm stereo jack
- Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
- Minimal Connected Impedance per Channel: 16 ohms
- Frequency Response: 20 Hz - 40,000 Hz
- THD 1 kHz Sine: 0.04%
- Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
- Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
- Power Supply: 9 V DC block battery, DC jack
- Operating Voltage: 9 V DC
- Power Consumption: Nom. 70 mA / Max. 150 mA
- Housing Material: plastic
- Housing Surface: soft-touch
- Housing Colour: black
- Width: 80 mm
- Height: 42.5 mm
- Depth: 133 mm
- Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable
|
The compact HX-3 Headphone Distribution Amplifier is the perfect accessory to quickly provide three high-performance stereo headphone feeds with individual level controls from line-level sources. The HX-3 can produce very high headphone levels with extremely low noise and distortion.
HX-3 Key Features
Great for radio, television, film, and music production applications, the battery-powered HX-3 accepts balanced XLR line-level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs. Its 1/4-inch loop-out can connect multiple HX-3's for additional headphone outputs. Headphones are connected to panel-mounted 1/4-inch stereo connectors.
The HX-3 has a durable aluminum chassis to withstand the punishment of field and studio environments. The unit is powered by inexpensive batteries (two-AA) or external 5-18 VDC.
The HX-3 can add headphone outputs to the 552, 302, MixPre-D, MM-1, and USBPre-2.
HX-3 Key Features List - Three isolated headphone outputs with individual volume controls.
- 125 dB dynamic range with flat frequency response.
- Durable 1/4-inch connectors, panel mounted for strength.
- Stereo or mono monitoring.
- Peak LED indicates headphone overload.
- Two balanced XLR line level inputs or unbalanced 1/4-inch and 1/8-inch stereo inputs.
- Loop Output to connect additional HX-3's in series.
- All-metal connectors solidly mounted to the chassis for durability and RF immunity.
- Free from "Pin-1" grounding problems.
- Internal battery-power for up to 18 hours from two AA alkaline batteries.
- Chassis-isolated 5 to 18 VDC input for easy external DC powering.
- Power LED indicates low battery power.
- High strength, extruded aluminum chassis with protective metal end panels.
|
Reviews
There are no reviews yet.