Content |
Headmic with cardioid capsule to use with the wireless systems EW-D1
Microphone | pre-polarized condenser | Sensitivity | 1.6 mV/Pa | Pick-up pattern | cardioid | Max. sound pressure level | 150 dB SPL |
---|
|
Shure WBH54B Black Headworn Condenser Microphone
WBH54B is a subminiature, electret condenser head worn microphone. It provides uncompromised
sound quality and reliability with minimal visibility in applications such as broadcast, theater, and touring.
Despite their small size, the condenser element delivers full, clear, and natural reproduction of speech
and vocals. The microphone features a durable, low-profile wire frame headband which is fully adjustable for
stability and comfort. A plastic carrying case protects the microphone and its accessories.
Features:
Supercardioid polar pattern provides maximum gain-before-feedback and ambient rejection
Extended frequency response tailored for vocal performances
Able to handle extremely high sound pressure levels (SPL)
Snap-fit foam windscreens stay in place during intensive movement
Available with an in-line preamp or with a TA4F connector for wireless applications
Black finish
TA4F connector for wireless applications
|
ansducer Type
Electret condenser
Polar Pattern
Omnidirectional
Frequency Response
20 to 20,000 Hz
Output Impedance
N / A
Sensitivity (open circuit voltage, @ 1 kHz, typical)
-41 dBV/Pa (9 mV)
Maximum SPL (1 kHz at 1% THD)
2500 Ω load: 107 dB SPL
1000 Ω load: 107 dB SPL
Signal-To-Noise Ratio
60 dB
Dynamic Range @ 1 kHz
2500 Ω load: 73 dB
1000 Ω load: 73 dB
Self-Noise (equivalent SPL, A-weighted, typical)
34 dB
Operating Temperature Range
-18°C (0°F) to 57°C (135°F)
Polarity
Positive pressure on diaphragm produces negative voltage on pin 3 with respect to pin 1
Power Requirements
+5 V DC (130 μA minimum)
Weight
19.76 g
|
Transducer Condenser
Polar Pattern Omnidirectional
Frequency Response 30Hz to 20kHz +/- 3dB
Dynamic Range (Typical) Not Specified by Manufacturer
Signal-to-Noise Ratio Equivalent Acoustic Noise: 29dBA SPL
Maximum Input Sound Level 130dB SPL
Power Requirements Operating Current: 500uA
Operating Voltage: 1 to 2V
Power Supply Voltage:
+3V with 2.7k ohm Load
+5V with 6.8k ohm Load
+9V with 15k ohm Load
Output Impedance 2k ohms
Output Connectors TA4-Female Connector for Shure Wireless Transmitters
Dimensions Not Specified by Manufacturer
Weight 0.07 oz (2g)
|
High-quality permanently polarized condenser headmic with omni-directional pick-up pattern
Τype: | Headset | Series Compatibility: | 3000/5000 Series |
|
Shure WCM16 Headworn Condenser Microphone
The Shure Model WCM16 headworn electret condenser microphone is intended for wireless use by
performers, lecturers, and others who require the highest quality voice pickup with maximum mobility.
Its wide frequency response, low RF susceptibility and reliable operation at temperature and humidity
extremes make the WCM16 suitable for virtually any vocal application. When used with the Shure bodypack
transmitters, the performance of the WCM16 closely resembles the finest conventional vocal microphones.
Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency
response to resemble the warmproximity effect of larger vocal microphones. Because of this low-end response, it
is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath
noise, even without the supplied foam pop screen.
The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and
from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits higher
gain-before-feedback without loss or masking of vocals.
Features:
Extra lightweight, adjustable headband stays secure and virtually disappears while being worn
Response comparable to finest conventional vocal microphones
Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other performers
Uniform polar pattern at all frequencies for maximum gain before feedback
High input clipping level eliminates overload distortion
Cable terminates as 4-pin mini connector
Supplied acoustic foam pop screen
Reliable at temperature and humidity extremes
Specifications:
Frequency Response
50 to 18,000 Hz
Polar Pattern
Hypercardioid, uniform with frequency
Output Impedance
1200 ohms
Output Level (close-talked at 1,000 Hz)
Open Circuit Voltage -55.0 dbV (1.8 mV) at 0.6 m
1 Pascal=94 db SPL
Maximum Sound Pressure Level
150 dB at 1% THD
Dynamic Range
121 dB
Output Noise
29 dB equivalent SPL, A-weighted
Signal-to-Noise Ratio
65 dB at 94 dB SPL
Polarity
Microphone: Positive sound pressure on diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground) of microphone output connector
Receiver-- 1/4" Phone Jack Output: Positive sound pressure on diaphragm produces positive voltage on tip of receiver 1/4" output connector
Receiver-- XLR Output: Positive sound pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 of the XLR output connector
Current Drain
0.35 mA
Recommended Operating Voltage
+5 Vdc (positive on pin 2, negative on pin 1)
Environmental Conditions
Operating Temperatures: -18 to 60 degrees C (0 to 140 degrees F)
Storage Temperatures: -29 to 66 degrees C (-20 to 150 degrees F)
Humidity: 0 to 95%
Cable
1.5m (5 ft), small-diameter, shielded, with 4-pin mini connector
Case Finish (Microphone and Headband)
Matte black enamel
Net Weight
36 g (1.27 oz)
|
Reviews
There are no reviews yet.