The DJ500 is a powerful, full-featured Class AB power amplifier with an output of 250W per channel 4 ohms and 500W in switchable bridge mode. It is especially suitable for mobile use by DJs and smaller bands and in permanent installations. The DJ500 has extensive protection circuitry and a power-on delay. The half perforated front […]
The DJ500 is a powerful, full-featured Class AB power amplifier with an output of 250W per channel 4 ohms and 500W in switchable bridge mode. It is especially suitable for mobile use by DJs and smaller bands and in permanent installations.
The DJ500 has extensive protection circuitry and a power-on delay. The half perforated front panel and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch helps eliminate ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.
The DJ500 functions in the entire frequency range of 20Hz – 20kHz with extremely high dependability, dynamics, and impulse fidelity.
Type: 2-channel
Output Power 1 KHz @ 4 ohms: 2 x 250 W
Output Power 1 KHz @ 8 ohms: 2 x 150 W
Output Power 1 KHz @ Bridge 8 ohms: 500 W
Output Circuity: Class A/B
Frequency Range: 20 – 20.000 Hz
THD: 0,05%
Voltage Gain: 30dB
Input Sensivity: 0,85V
Protection: Soft start, short circuit, DC, Temperature, over current
The DJ500 is a powerful, full-featured Class AB power amplifier with an output of 250W per channel 4 ohms and 500W in switchable bridge mode. It is especially suitable for mobile use by DJs and smaller bands and in permanent installations.
The DJ500 has extensive protection circuitry and a power-on delay. The half perforated front panel and a low-noise fan keep the amp cool. XLR and stereo TRS sockets are used as inputs and Speakon-compatible sockets and heavy-duty screw terminals as outputs. A ground lift switch helps eliminate ground loop hum. LEDs on the front panel next to the easy-grip volume controls indicate functional status, overloading, and triggering of the protection circuit.
The DJ500 functions in the entire frequency range of 20Hz - 20kHz with extremely high dependability, dynamics, and impulse fidelity.
Type: 2-channel
Output Power 1 KHz @ 4 ohms: 2 x 250 W
Output Power 1 KHz @ 8 ohms: 2 x 150 W
Output Power 1 KHz @ Bridge 8 ohms: 500 W
Output Circuity: Class A/B
Frequency Range: 20 - 20.000 Hz
THD: 0,05%
Voltage Gain: 30dB
Input Sensivity: 0,85V
Protection: Soft start, short circuit, DC, Temperature, over current
Connectors Speaker Output: 2 x Speakon compatible, 2 x binding post
Cooling System: Fan
Power Supply: 230V / 50-60 Hz
Dimensions (W x H x D): 483 x 88 x 298 mm
Engineered from the ground up for unmatched quality and performance, the Crown? DSi Series of power amplifiers offers three models of 500W, 800W, and 1200W per channel at 4 ohms. Onboard digital signal processing includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15 connector provides easy input/output connectivity between DSi amplifiers and the new DSi-8M System Monitor. The intuitive front panel LCD screen guides installers through a setup process? featuring presets for the industry-standard JBL cinema loudspeaker systems? to make configuration quick and easy. At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched performance with each award-winning JBL ScreenArray? system, making this the ultimate cinema solution.
Features : Includes three models of 500W, 800W, and 1200W per channel at 4 ohms Automatic presets for popular JBL cinema speaker systems for quick, easy configuration Intuitive front-panel LCD screen guides installers through setup Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting Computer connectivity via USB allows fast setup and configuration with HiQnet? System Architect? software Rear-panel HD-15 connector provides easy input/output connectivity between DSi amplifiers and new DSi-8M System Monitor Switch-mode universal power supply All products fill 2U rack spaces and weigh under 19 pounds Barrier strip outputs, removable Phoenix-style input Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifi er and the DSi-8M System Monitor. The outputs shall be usable as stereo or bridged-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. Front panel controls and indicators shall include the following: Level: Detented rotary level control, one per channel. Power Switch: On/off switch applies AC power to the amplifi er. Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items. LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing. Signal Indicator: Green LED, one per channel, fl ashes when a very low-level signal is present at input. ?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below clip. ?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB below clip. Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is ready to produce audio. Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion. Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or excessive temperature conditions. Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power. Rear panel controls and connectors shall include the following: AC Line Connector: NEMA 5-15P (15A). Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal. Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker. HiQnet USB Connector: Type B, connects to a HiQnet network. HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor. The amplifi er shall have the following specifi cations: Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo (per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with 0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono: 1,000W with 0.5% THD. Voltage Gain at 1kHz, 8 ohm rated output: 26 dB. Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity at 8 ohm rated output: 2.35V. Sensitivity at 4 ohm rated output: 2.24V. Sensitivity at 2 ohm rated output: 1.88V. Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 500 Hz. Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz. Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical. AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V, 50/60 Hz. AC Line Current: 6.5A. At Idle: Draws no more than 90 watts. Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing). The DSP section shall have the following specifi cations: EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also adjustable high and low shelving fi lters. Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per channel. Delay: Up to 50 msec total delay per channel. Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6, or ?12 dB threshold per channel. Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL system presets. Protection shall include the following: DSi-Series amplifi ers shall be protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; excessive output current, and input overload damage. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients The chassis shall be steel. Cooling shall be by a proportional speed fan with front-to-rear airfl ow. Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface. Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
Solid DYNACORD technology for fixed installations at very competitive prices. DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch. The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.
The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Output circuitry
Class H
Frequency response
20 - 20000 Hz
THD
< 0.1 %
Signal-to-noise ratio
105 dB
Damping factor
> 400
Crosstalk
>80 dB
Gain
35 dB
Input sensitivity
0.75 V
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
 170W+170W<br>
4ohm(T.H.D 0.05%) 250W+250W<br>
</p>
<p>
BRIDGED MONO <br>
8ohm(T.H.D 0.05%) 460W<br>
8ohm(T.H.D 0.5%) 500W
</p>
<p>
Frequency Response 20Hz- 20kHz, ±0.5dB
</p>
<p>
Convection Cooled
</p>
<p>
SoftStart Protection System
</p>
<p>
Balanced 10kΩ@0.775V Inputs
</p>
<p>
</p></td><td>
<p>XB Series - Intelligent Power</p>
<p>Power Without Compromises.<br>The XB is designed for paging, music and alarm signals. Versatile, dynamic <br>and extremely rugged according to IEC286-3. For the highest requirements <br>in safety and quality.<br>Sequential power on, alive contacts and incorporated ground fault detection- <br>the XB is the solution under all conditions. Without the need for additional <br>equipment. For uninterrupted and troublefree operation.</p>
<p>High Tech SMT Design <br>Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, <br>3 ms Muting Delay <br>PHOENIX / Speakon <br>LED Indicators for POWER, SIGNAL, CLIP, PROTECT <br>Temperature controlled, variable speed low noise fans <br>Volume Controls at the back <br>Stereo / Bridged / Parallel Mode <br>Softstart <br>Sequential Remote Power On <br>Alive Contact <br>Ground Lift <br>3 Years Warranty </p>
<p>TECHNICAL DATA:<br>XB 800: 2x 400 W @ 4 Ohm<br>Class: AB<br>Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)<br>THD: < 0.025%<br>Signal-to-Noise Ratio: < 103 dB<br>Channel Seperation: > 85 dB<br>Input Sensitivity: +6 dBu<br>Input Clipping: 22 dBu<br>Input Impedance: 20 kOhm<br>Damping Factor: 500 @ 4 Ohm<br>Cooling: 2x fan (temp. reg. variable speed)<br>Weight: 13 kg/(29 lbs) <br>Dimensions: 2 RU / 483 x 88 x 382 mm (19 "acrobat_reader_logo."){kind=logo}
Reviews
There are no reviews yet.