| Content | The directional condenser microphones equipped on the TM-2X are the same mics used in our highly-regarded DR-series recorders. The X-Y pattern and two mic capsules are ideal for capturing a true representation of the sonic atmosphere, whether it\'s sound from a wide area or directly in front of the camera. As a result, the TM-2X records pristine sound that fits naturally with the recorded video.
Setup is as simple as connecting the cord from the TM-2X to the camera\'s mic input jack allowing you to add high-quality audio to video. The output can be set to one of two levels to enable compatibility with a variety of cameras.
TM-2X SPECIFICATIONS
| Microphone type |
cardioid |
| Frequency range |
50Hz to 20kHz |
| Input output ratings |
|
| Maximum input level |
120dB SPL (at 1kHz, SENS:H, LCF=Flat, RL:2.2kΩ, Vcc:2.5V) |
| Output impedance |
1.6k ohms (RL:2.2kΩ, Vcc:2.5V) |
| S/N ratio |
74dB (at 1kHz, 1Pa, A weighted) |
| Mic sensitivity switch |
SENS H:-37dB, SENS L:-52dB
(at 1kHz, 0dB=1V/Pa, RL:2.2kΩ, Vcc:2.5V) |
| Connection cable/plug |
|
| Cable length |
33cm |
| Plug |
3.5 mm (1/8\'“) TRS stereo mini plug
(Tip: left channel, Ring: right channel, Sleeve: GND) |
| Power |
Plug-in power (JEITA standard CP-1203A) |
| Dimensions |
|
| TM-2X main unit |
57(W)×59(H)×69(D)mm(not including cable and connectors) |
| Noise isolation arm |
34(W)×57(H)×142(D)mm |
| Weight |
|
| TM-2X main unit |
75g |
| Noise isolation arm |
41g |
| Operating temerature |
-5 to 45˚C
23 to 142˚F |
| Accessories |
Fur windscreen, noise isolation arm, Owner\'s Manual, warranty |
|
The CS-50 is a compact, light-weight stereo condenser microphone designed for the R-4 and R-4 Pro, videographer, broadcaster, and sound designer. The CS-50 features bass roll-off capability as well as selectable wide stereo or narrow (focused) polar patterns.
From Edirol, the CS-50 Stereo Microphone is designed for use with the Edirol/Roland R4 portable digital field recorder. The microphone features wide stereo and narrow polar patterns. The wide stereo pattern reproduces audio with accurate stereo imaging while the mono pattern is focused and reduces signal at the sides of the capsule. The CS-50 features a low frequency roll-off switch for eliminating hum and low-frequency noise due to wind or proximity effect. A dual XLR output cable is supplied.
Wide Stereo PatternThe wide stereo pattern provides a generous pick up area while reproducing signal with accurate stereo placement. This setting is ideal for ambiance capturing, live music, sound effects, etc.Mono (Narrow) PatternThe narrow pattern provides a focused pick up at the front end of the capsule. The result is an accurate signal without noise at the off-axis sections of the capsule.Low Frequency Roll-OffThe low-frequency roll-off switch eliminates hum and low-frequency noise due to wind, handling and proximity effect.Light Weight ProfileThe light weight, slim profile make the CS-50 ideal for location use while mounted on a boom, pistol grip or camera.
What's in the Box:
- Windscreen
- Desktop Prop
- Mic Stand Adapter
- L/R XLR Cable 6.56 feet (2m)
- Soft case
- 1 Year Warranty
Specifications: | ransducer | Back Electret Condenser | | Polar Pattern | Line Cardioid | | Frequency Response |
50 - 20,000Hz
| | Open Circuit Sensitivity | 14.9 mV/Pa, -36.5 dBV @ 1 Pa | | Dynamic Range (Typical) | Not Specified by Manufacturer | | Signal-to-Noise Ratio | Greater than 70dB (at 1kHz/1Pa) | | Maximum Input Sound Level | 126dB S.P.L (at 1kHz, 1% T.H.D. Typical) | | Power Requirements | 48V Phantom x 2ch | | Output Impedance | 200 Ohms | | Current Consumption | 3.8 mA (Typical) | | Output Connectors | 3-pin XLR | | Pad | No | | Low Frequency Roll-Off | Yes | | Dimensions | Not Specified by Manufacturer | | Weight | 2.92 oz (83g) |
|
Element: Externally polarized (DC bias) capacitor
Polar Pattern: Line + gradient
Frequency Response: 20-18,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: -29 dB (35.5 mV) re 1V at 1 Pa
Impedance: 50 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad (nominal)
Dynamic Range: 128 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 81 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 48V DC, 4.8 mA typical
Weight: 175 g (6.2 oz)
Dimensions: 539.0 mm (21.22“) long, 21.0 mm (0.83“) maximum body diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8147 windscreen; two O-Rings; protective carrying case
| OLED display (on receiver)
One button pairing
Three level gain control
AA battery or USB powered
Includes RØDE\'s broadcast Lavalier microphone
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres (over 100 yards). The RØDELink Filmmaker Kit provides everything you need to start shooting video wirelessly, including a receiver, transmitter and broadcast-grade lavalier microphone. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The lightweight transmitter (TX-BELT) can be fitted to a belt or clothing and features a locking thread to ensure the microphone connection is as secure as possible. RØDEʼs omnidirectional Lavalier microphone is included in the kit to provide the highest possible audio reproduction quality.
RØDELink Filmmaker Kit Specifications
Transmission type 2.4GHz Fixed Frequency Agile System
System dynamic range 112dB
Range (distance) 100m
Frequency range 35Hz - 22kHz
Maximum output level 1v Rms (2.8v P-p)
Max input signal level 1v Rms (2.8v P-p)
Max latency 4ms
Receiver (RX-CAM)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket - Dual Mono
Output impedance 300Ω
Dimensions 111mm X 65mm X 52mm
Weight 190gm
Transmitter (TX-BELT)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket
Output impedance 10kΩ
Dimensions 111mm X 65mm X 40mm
Weight 190gm
Lavalier
Acoustic Principle Pressure Gradient
Active Electronics JFET impedance converter
Capsule 0.10“
Address Type End
Frequency Range 60Hz - 18kHz
Output Impedance 3000Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 25dB-A
Weight 1.00gm
Dimensions 12.00mmH x 4.50mmW x 4.50mmD
Warranty 10 year warranty |
Audio-Technicaʼs high-SPL BP892 MicroSet® offers the ultimate in low-profile, high-performance audio. Delivering clear and accurate sound in an inconspicuous package, the ultra-lightweight BP892 hooks securely behind either ear and can be worn for hours without fatigue. For maximum stability and comfort, the included AT8464 dual-ear microphone mount converts the MicroSet to a dual-ear-worn unit.
The microphone features a flat, extended frequency response and other outstanding performance specifications, resulting in extremely intelligible, natural audio for stage and television talent, lecturers and houses of worship. Protected by a highly durable Parylene coating, the new headworn mic is built to stand up to the rigors of day-to-day use.
Handles high sound pressure levels with ease
Extremely intelligible natural audio
Inconspicuous, lightweight headset with capsule diameter of just 2.6 mm is ideal for applications requiring minimum visibility
Ergonomic under-ear design—flexible, lightweight contoured loop hooks behind the ear for an ultra-secure, comfortable fit with or without glasses
Comes equipped with AT8464 Dual-Ear Microphone Mount that converts single ear-worn MicroSet to a dual-ear-worn unit for maximum stability and comfort
High-pass filter on power module provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Omnidirectional
Frequency Response: 20-20,000 Hz
Low Frequency Roll-Off: 80 Hz, 18 dB/octave (wired only)
Open Circuit Sensitivity: –49 dB (3.5 mV) re 1V at 1 Pa
Impedance: 250 ohms (wired only)
Maximum Input Sound Level: 135 dB SPL, 1 kHz at 3% T.H.D.
Dynamic Range: (Typical) 104 dB, 1 kHz at Max SPL (wired only)
Signal-To-Noise Ratio: 63 dB, 1 kHz at 1 Pa
Phantom Power Requirements: 11-52V DC, 2 mA typical (wired only)
Switch: Flat, roll-off (wired only)
Current Consumption: 0.1 mA typical at 5V (wireless only)
Voltage Range: 2.5-11V (wireless only)
Weight (Microphone): Microphone, boom & earpiece: 2.6 g (0.09 oz)
Weight (Power Module): 85 g (3.0 oz) (wired only)
Dimensions Microphone: 8.1 mm (0.32“) long, 2.6 mm (0.10“) diameter Boom: 98.4 mm (3.87“) long, 1.07 mm (0.04“) diameter
Dimensions (Power Module)@ 97.6 mm (3.84“) long, 18.9 mm (0.74“) diameter (wired only)
Output Connector: (Power Module) Integral 3-pin XLRM-type
Cable: 1.4 m (55“) long (permanently attached to microphone), 1.6 mm (0.06“) diameter, 2-conductor shielded cable with locking 4-pin connector (wired only)
Accessories Furnished: BP892: AT8539 power module (wired only); AT8464 dual-ear microphone mount; AT8440 cable clip; two AT8157 windscreens; two AT8156 element covers; moisture guard; belt clip (wired only); carrying case BP892-TH: AT8539 power module (wired only); AT8464-TH dual-ear microphone mount; AT8440 cable clip; two AT8157-TH windscreens; two AT8156-TH element covers; moisture guard; belt clip (wired only); carrying case
Audio-Technica Case Style: M31
|
Broadcast sound quality
Low noise circuitry
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
Ten year extended warranty with online registration
The NTG4 builds on the platform created by RØDE's award-winning NTG1 shotgun microphone. A broadcast-quality directional condenser microphone designed to provide premium audio recording in a versatile range of applications including on-camera and boom mounted.
Visit the NTG4 feature page
NTG4 Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom power
Weight 126gm
Dimensions 225mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration
|
Reviews
There are no reviews yet.