TRUETONE 1SPOT ADAPTOR CONVERTER BARREL NEG INS TO MINI JACK 3.5MM

• Connector: Coaxial connector (negative pole inside) to 3.5 mm (1/8“) mini-connector (positive pole on tip)
• For older Dunlop, MXR, DOD, Frantone, Pro Co and Electro Harmonix effects with mini-jack connector

• Choice of 9V DC, 12V DC, 12V AC or 18VDC -150mA
• Noise-cancelling galvanic isolated outputs
• Traditional EI Transformer
• Several different voltage types served
• Current doubler = the possibility of as much as 600 mA
• Switchable 115V or 230V
• Compact, rugged, road-ready design

Universal Effects Pedal Floor Board with 9 V DC Power Supply and Patch Cables
Ultra-compact and lightweight pedal board for transporting up to 6 effects pedals, including patch cables
Generous 1.7 A power adapter included for powering more than 12 devices*—includes 1 x 6 daisy-chain cabling
Ultra-rigid plastic design withstands even heavy impact
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

When effects are an integral part of your rig, their power adapters and patch cables can often be the most vulnerable part, and the most likely to sabotage your set if they're not pampered. Rather than tossing your pedals, power adapters and all other cabling into a duffel bag after a gig, keep them safe—and ready to rock at a momentʼs notice—with the PB600.
It's All About Connections
This awesome pedal board makes hooking up six 2.5" x 4.5" pedals as easy as hooking up just one (of course, if youʼre using pedals that arenʼt 2.5" x 4.5“, the snug foam padding can be cut to accommodate pedals of varying shapes). The PB600 includes 1/4" patch cables, so you can leave your pedals connected to one another, ready to pass signal even when youʼre transporting them. It also comes with 1 x 6 daisy chain cabling so that when you plug in the 1.7 A power adapter, all your pedals receive power. Meanwhile, all cabling remains safe and free of strain. Failure is almost guaranteed when youʼre dealing with a ratʼs nest of loose cabling, but with the PB600, your effects chain is always safe and organized.

When itʼs time to load out, just unplug the power supply, disconnect your guitar and amp, put the lid back on the PB600 and slide the locking latches back into place. The heavyimpact plastic casing will protect your pedals from the very worst dings, scrapes and scratches the road throws your way.

User's Manual

Keep your pedals powered all night long with the MXR DC Brick, a revamp of the DCB10. Now under the MXR brand, the new DC Brick features all of the short circuit and overload protection of the original but now handles twice the power, allowing you to use virtually any combination of effects. Additionally, each 9v output has a red LED that illuminates if there is a short so you can quickly identify and troubleshoot any power problems. The MXR DC Brick has eight 9v outputs and two 18v outputs, a change from the DCB10ʼs seven 9v outputs and three 18v outputs. And of course, the AC adapter and all necessary cables to connect pedals to the unit are included.

The PWT12 is universal pedal board power supply with 12 outputs electrically isolated in pairs. Outputs 1 - 8 provide 9 V DC each with a maximum current draw of 250 mA per pair. Outputs 7 and 8 additionally feature a polarity switch to change the center pin from negative to positive (and the barrel to negative).

Outputs 9/10 provide 18 V DC each with a maximum current draw of 125 mA. Additionally, the upper output is switchable to 12 V DC. Providing 9 V DC/250 mA, outputs 11/12 are also switchable to 12 V AC. The green indicator LEDs turn red when alternative ouput voltages are selected.

All output pairs are individually protected against shorts and overload. When a fuse trips the LED indicator of the corresponding pair goes out. After the fault condition has been removed the fuse is automatically reset, and within a few seconds the output resumes operation indicated by the illuminated LED.

The toroidal transformer and the steel housing of the PWT12 provide smooth FX operation free of interference and hum pickup. Mains power input is switchable between 115 V and 230 V.

The PWT12 features two brackets for easy pedal board mounting while a cover plate protects the DC plugs. The DC cables can be fixed to the plate with cable ties for strain relief. The PWT12 comes with a set of 12 long DC cables.

• Universal power supply for effect pedals
• 12 outputs on barrel-style DC connectors with 2.1 mm center pin
• regulated DC output, all outputs electrically isolated in pairs
• Outputs 1/2, 3/4, 5/6: 9 VDC each, 250 mA per pair, center pin negative, green LED indicators
• Outputs 7/8: 9 VDC, 250 mA/pair, switchable polarity, two-color LED, green = center pin negative, red = center pin positive
• Outputs 9/10: 2x 18VDC (LED = green), switchable to 1x 12VDC / 1x 18VDC (LED = red), maximum current 125mA/pair, center pin negative
• Short circuit protection per pair with automatic reset
• 115 V / 230 V switchable
• Mains fuse: 5 x 20 mm fine wire, 115 V = T 500 mA;  230 V = T 250 mA
• Toroidal transformer, 20 VA continuous

Power supply uniy for Fly 3