| Content |
With an enclosure height to match the height of 60-inch plasma screens, the FPM6 is the largest model in the FPM Series.
With an enclosure height to match the height of 60-inch plasma screens, the FPM6 is the largest model in the FPM Series. Compared to the other models, its enclosure is not only longer, it's wider too, which allows the use of two larger Kevlar® cone bass/midrange drivers each side of the Nautilus™ tube-loaded tweeter. Higher output level capability and greater bass extension result, but timbre matching allows complete freedom to mix different models for left and right front, centre and surround if desired.
Freedom and flexibility extend to the four possible mounting options. Use the supplied wall bracket if no tilting of the speaker is needed. If it is, use an Omnimount® type 20.0 or other compatible bracket to get up to 10º of downward tilt. If using a tabletop stand for your screen, simply do the same with the speakers, using the optional table stand. Finally, there is an optional floor stand that supports the speaker at the ideal listening height.
|
Driver Complement
Mid/Woofer 1 - 6-1/2" Diameter (16.51cm)
Dynamic Balance polymer composite cone driver
Tweeter 1 - 3/4" Diameter (1.91cm)
Silk Dome Tweeter
Electrical
Overall Frequency Response 40Hz-20kHz
Lower -3dB Limit 60Hz
Upper -3dB Limit 20kHZ
Nominal Impedance 8 ohms
Recommended Amplifier Power 20-100 w/channel
Efficiency 89 dB
Dimensions
Overall Diameter 9-5/16“(23.65cm)
Cut-out Diameter 8-3/16“(20.80cm)
Mounting Depth
(assumes 1/2" [12.7mm] wall material) 3-3/8" (8.57cm)
Overall Depth 3-7/8" (9.84cm)
Shipping/Other
Shipped As each
Product Weight 3.25 lbs. (1.47kgs) each
Total Shipping Weight 5.00 lbs. (2.27kgs)
|
Outer Flange Dimensions | Metric :11” x 12-3/4” | 27.9 x 32.4cm
Cut Out Dimensions | Metric :9-7/8” x 11-5/8” | 25.1 x 29.5 cm
Depth from Flange | Metric :3-7/8” | 9.8 cm
Driver Complement :Two 1" pure aluminum dome tweeters; Two 4-1/2" cast-basket bass/midrange drivers pressure coupled to two 4-1/2” bass radiators
Frequency Response :26 Hz – 30 kHz
Impedance :Compatible with 8 Ohm outputs
Sensitivity :90 dB
Recommended Associated Amplifier Power :10 – 200 watts
A/V Receiver Crossover Setting :80 Hz
Inputs :One pair of gold plated spring loaded posts
Enclosure :Sealed Medite
Available Finishes :Paintable White
Accessories :Paint mask; Cut-out template
Packaging :One to a carton
Warranty :5 Years
Weight | Metric :13 lbs | 5.9 kg |
Features:
Consistent 90° broadband pattern control. Kevlar-reinforced 300 mm (12 in) woofer with 75 mm (3 inch) voice-coil cone. Medium-format compression driver. Extraordinary clarity for speech and vocals with extended frequency response for music. Power handling of 400 Watts with high sensitivity provides high SPL capability. Advanced high-slope crossover network for constant coverage and smooth, natural midrange.
Specifications:
Frequency Response 48 Hz - 19 kHz, +/-3dB (in ceiling) Maximum Power Handling 1600 Watts, 2 hrs., pink noise 1000 Watts, 100 hrs. Impedance 8 Ohms SPL 121dB avg., 124dB peak Beamwidth 90° conical, broadband (1kHz - 10kHz) Horizontal Beamwidth 90° conical, broadband (1kHz - 10kHz) Vertical Beamwidth 90° conical, broadband (1kHz - 10kHz) Directivity Factor: 9.0 (1kHz - 16kHz) Index: 9.5dB (1kHz - 16kHz) Construction Kevlar-reinforced cone woofer Medium-Format compression driver with radial slot phase plug Ported Metal Baffle Magnet LF: Saturated-gap geometry HF: Neodymium Voice Coil LF: 3" HF: 1.5" Dimensions (HxWxD) 14.4 x 14.4 x 8.8" (366 x 366 x 223mm) Weight 20 lb (9.1 kg)
| Key Features:
Clear, High-Fidelity Performance
6W Transformer for use on 70V / 100V
Distributed Lines
Dog-Ears for Easy Blind Mount
Installations
High Sensitivity for Maximum Power
Efficiency
Open-back design for applications not
requiring an in-ceiling backcan.
Specifications (8124):
Component: 100 mm (4 in) Full-Range
Frequency Range (-10 dB): 60 Hz – 18 kHz
Coverage: 130° conical
Sensitivity (2.83V@ 1m): 93 dB (1 kHz - 8 kHz)
Termination: Bare Wire
Nominal Driver Impedance: 8 ohms
Driver Power Capacity: 20 W
70V/100V Transformer Taps: 6 W, 3 W, 1.5 W, (0.75 W at 70 V only)
Dimensions (Diameter x Depth): 206 mm (8.1 in) diameter round baffle x 89 mm (3.75 in)
depth from back of baffle
Cutout Dimension: 175 mm diameter (6.9 in)
Net Weight: 1.2 kg (2.5 lb)
Included Accessories: Sculpted Grille
Optional Accessories: MTC-8124C C-ring
MTC-RAIL tile rails
Plenum Usage: Not intended for use in return air plenums |
Outer Flange Dimensions | Metric :15-1/2” W x 15-1/2” H | 39.4 x 39.4 cm
Cut Out Dimensions | Metric :14-3/8” W x 14-3/8” H | 36.5 x .36.5 cm
Depth from Flange | Metric :5-7/8” | 14.9 cm
Driver Complement :Two 1" pure aluminum dome tweeters; Two 5-1/4" cast-basket bass/midrange drivers pressure coupled to two 6-1/2” bass radiators
Frequency Response :22 Hz – 30 kHz
Impedance :Compatible with 8 Ohm outputs
Sensitivity :
Recommended Associated Amplifier Power :10 – 250 watts
A/V Receiver Crossover Setting :40 Hz
Inputs :One pair of gold plated spring loaded posts
Enclosure :Sealed Medite
Available Finishes :Paintable White
Accessories :Paint mask; Cut-out template
Packaging :One to a carton
Weight | Metric :22 lbs | 10 kg
Warranty :5 Years
|
Reviews
There are no reviews yet.