ZOOM F1-LP 2 Track Field Recorder with Lavalier Mic (Set)

• Two-channel audio recorder
• Compatible with zoom microphone capsules
• Supports WAV formats up to 24bit / 96kHz or MP3 formats on microSD / microSDHC card (up to 32GB)
• USB audio interface for PC and Mac (class compliant)
• Rec Hold function for protection against accidental operation of the keys
• Switchable limiter and impact sound filter
• Automatic modulation
• Internal clock for timestamp function
• Power supply: USB or 2 NiMH batteries / rechargeable batteries (AAA)
• Weight: 120 g (without batteries)

Connections:

• Input for ZOOM microphone capsule
• Microphone input 3.5 mm mini-jack with screw connection
• Stereo headphone output
• Micro-USB for file transfer to computer

Scope of delivery:

• F1 Field Recorder
• LMF-1 Lavalier microphone
• WSL-1 Windshield
• MA-1 Microphone clamp
• BCF-1 Belt clip
• 2 AAA batteries
• Quick start Guide

The Apogee X-VID-SYC-GEN Video Expansion Card is designed to fit in the X-Series card slot located in the rear panel of the Apogee Big Ben Master Digital Clock (sold separately). Allows all functions to be controlled from the Big Ben user interface and generates video and provides genlocking function. In genlocking mode the source video-signal will be re-clocked and regenerated, maintaining the same
field and colorburst phase information, but stripped of its line information and replaced by video-black. In slave mode the board will auto-detect the incoming video-standard and configure itself accordingly. The video input is of very high tolerance and will even lock to unstable sources like VCR's.

The Apogee X-VID-SYC-GEN Video Expansion Board has three modes of operation.
•Master mode: The user selects the video format on the frontpanel of the Big Ben. The Big Ben will slave to the generated video signal


•Attended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben will slave to the incoming video signal

•Unattended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben is not clocking to the Video board and therefore both will function independently

• Support for PAL, NTSC and 60 Hz B&W standards
• One composite video input and three composite video outputs
• Can operate as a master black-burst generator
• Can operate as genlocking slave device

Stereo Rack Memory Recorder
The UR-2 is a 1 U rack size stereo audio recorder using SD card and USB storage device that is flexibly adapting to the wide variety of playback requirements.
The UR-2 is a new generation stereo memory recorder from Fostex that uses 2 SD cards (SDHC compatible) and USB storage device as the recording media. The recording/ playback file format is BWF (WAV). Its ample playback functions will adapt to the wide variety of playback requirements. It offers high quality recording of up to 24bit/96kHz (in BWF format). Employing FAT 32 disc format, it is easy to process the file transfer to a PC based DAW.
The analog input and output are balanced XLR/+4dBu and un-balanced RCA/-10dBV, the digital input and output complies to AES/EBU and S/P DIF digital signal. It is flexible to be used in the available audio system. The playback function includes Chain Play and Timer Play, it is suitable for live stage performance and sound installation. In addition to the external control via parallel remote with D-Sub 25pin and RS-232C serial remote, a USB keyboard and 10-key keyboard can trigger the instant playback start, which is very useful at a live event, theater and broadcast environments.
The Mic input located on the front panel offers 48V phantom power, it can be used not only for recording but also for speech to be mixed with playback source. Last but not least, its newly employed organic EL display gives an extremely clear visibility. This combined with DC power operation, it serves for outdoor use very well.

MAIN FEATURES
• 2 sets SD card slots and a USB host connector for alternate recording/playback among the different media.
• Stereo or Mono WAV (BWF) recording to SD card (also SDHC) and USB storage device
• Fs: 44.1/48/88.2/96kHz, Quantization: 16/24bit
• High speed file transfer with PC via USB 2.0 (bi-directional)
• Employing FAT32 format, it allows to directly mount the recorded files to PC.
• It adapts to a wide variety of use environment by offering Chain Play and Memory Play.
• Timer Play and Power ON Play enable automatic playback start for such as chime and repetitive announcement, which are convenient in the installation audio industry.
• The play mode list employs CSV file format so that it is easy to edit by a text editor or spread sheet program software on PC.
• 99 Cue points with locate function. Waveform display under Scrub mode offers easy and visual Cue point setting
• Microphone input with P48V available on the front panel. Not only for recording but for speech to be mixed with playback source.
• Analog I/O with balanced XLR and un-balanced RCA pin jacks, Digital I/O with XLR connectors
• An organic EL display offers high visibility.
• Remote transport control via Foot SW, Parallel remote pot (Dsub 25pin) and RS-232C (D-sub 9pin)
• External USB keyboard can be used not only for file name editing but for transport control such as REC and PLAY.

Specifications
General
Recording media         CompactFlash card
  Tested media         SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system         FAT32
File format         BWF (single-channel, multi-channel)
Number of audio channels         8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates         16 bit/24 bit
Sampling frequencies         44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock         Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates         23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic         Omni directional, monaural
Low cut filter         Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8)         XLR-3-31 (1: GND, 2: HOT, 3: COLD)
  Input impedance (LINE)         10 kOhm
  Nominal input level (LINE)         + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
  Maximum input level (LINE)         Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
  Input impedance (MIC –25)         2.4 kOhm
  Minimum input level (MIC –25)         –45 dBu
  Maximum iput level (MIC –25)         +11 dBu
  Input impedance (MIC 0)         2.4 kOhm
  Minimum input level (MIC 0)         –70 dBu
  Maximum input level (MIC 0)         –14 dBu
LINE OUT connectors (L/R)         XLR-3-32 (1: GND, 2: HOT, 3: COLD)
  Output impedance         100 Ohm or less
  Nominal output level         +6 dBu (Ref. level: –9 dB)
  Nominal output level         +4 dBu (Ref. level: Other than –9 dB)
  Maximum output level         Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector         6.3-mm stereo phone jack
  Maximum output power         100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector         D-Sub, 25-pin connector
  Format         AES3-2003/IEC60958-4 (AES/EBU)
  Minimum input voltage         200 mVpp
  Maximum input voltage         7 Vpp
  Output voltage         3.5 Vpp
DIGITAL OUT connectors         BNC
  Format         AES3-2003/AES-3id-2001 (AES/EBU)
  Output voltage         1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector         XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
  Input voltage         11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector         BNC
  Input voltage         5 V TTL equivalent
  Input impedance         75 Ohm ±10 %
  Allowable frequency deviation of external sync         ±100 ppm
CASCADE/WORD OUT connector         BNC
  Output voltage         5 V TTL equivalent
  Output impedance         75 Ohm ±10 %
  Sampling frequencies         44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector         BNC
  Input voltage         0.5–5 Vpp
  Input impedance         10 kOhm
TIME CODE OUT connector         BNC
  Output voltage         2.0 Vpp
  Output impedance         600 Ohm
USB port         USB B-type, 4-pin
  Format         USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector         Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)          
  All sample rates         20 Hz – 20 kHz, 0 dB (±0.5 dB)
  88.2/96 kHz sample rates         at 40 kHz –1 dB (±1.0 dB)
  176.4/192 kHz sample rates         at 80 kHz –3 dB (+1/–2 dB)
Distortion          
  LINE IN to LINE OUT         0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
  MIC IN (MIC –25) to LINE OUT         0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
  MIC IN (MIC 0) to LINE OUT         0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio          
  LINE IN to LINE OUT         110 dB(A) or more (22 kHz LPF)
  MIC IN (MIC –25 or MIC 0) to LINE OUT         100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows         Windows XP, Windows Vista, Windows 7
  CPU         Pentium 300 MHz or faster
  Memory         128 MB or more
  USB         USB 2.0 port
Macintosh         Macintosh Mac OS X 10.2 or later
  CPU         Power PC G3, G4, Intel Mac 266 MHz or faster
  Memory         64 MB or more
  USB         USB 2.0 port
Recommended USB host controller         Intel chipset
Power supply and other specifications
Power requirements         100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation)         Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
  NP type battery (Li-Ion: 14.8 V/4.6 Ah)         About 5 hours
  AA type batteries (NiMH)         About 2 hours
Power consumption         18 W
Dimensions (W x H x D)         270 mm x 100 mm x 260 mm (excluding protrusions)
Weight         3.65 kg (excluding batteries)
Operating temperature range         0–40 ºC

Liquid Mix HDLiquid Mix HD | TDM Plugin for Pro Tools HD

Key Features
Variety of Classic Emulations
40 compressors and 20 EQs, sampled from vintage originals with a free expanding library online.
Dynamic Convolution Technology
The unique patented Dynamic Convolution process delivers unparalleled EQ and Compression emulations.
Ultra-Low Latency for Recording
With the ultra-low latency of Liquid Mix HD (just 12 samples), it can now be used for recording and live sound applications
Optimised for Pro Tools HD
Over one hundred simultaneous mono instances can be run at 44.1/48kHz on an HD3 system.
Full Control Surface Mapping
Pro Tools TDM format ensures full control mapping on all major Pro Tools control surfaces, including ICON and VENUE.
Unique Hybrid Super EQ
Create your own totally unique 7-band super EQ, built out of separate classic EQ bands.
Compressor 'Free' Mode
Vintage compressors with limited controls can now be set to provide fully variable Attack, Release and Ratio.
Automation and Full Recall
Perfect integration with Pro Tools HD allows for automation of parameters and full recall within your session.

* 8-track Digital Portastudio with CD Burner
* Records to SD/SDHC Card media
* Import audio tracks from CD
* Built-in stereo condenser microphone
* Two XLR microphone inputs with phantom power
* 1/4" stereo line inputs
* Switchable instrument-level input for guitar/bass direct recording
* Multi-band mastering effects
* 2-band EQ per track
* Internal reverb processor with dedicated send per track
* Chromatic Tuner and Metronome
* Track editing, autopunch and bounce features
* Optional RC-3F footswitch offers three switches for punch-in and transport operation
* Compact and lightweight
* Dimensions: 11.4" W x 2.1" H x 8.2" D
* Weight: 4lbs