| Content | Το D&R Hybrid-1 είναι ένα αναλογικό τηλεφωνικό υβρίδιο, με δυνατότητα ελέγχου τοπικά. Δεν απαιτεί εξωτερική τροφοδοσία ρεύματος καθώς τροφοδοτείται από την τηλεφωνική γραμμή.
- είσοδος και έξοδος ήχου(jack 6,3 χιλ.)
-Υποδοχή 2 καλωδίων με παράλληλη έξοδο για σύνδεση εξωτερικής τηλεφωνικής συσκευής.
-Τοπικός έλεγχος των λειτουργιών αποδοχής-απόρριψης γραμμής και ειδοποίηση εισερχόμενης κλήσης.
-Αυτόματη αντιστάθμιση επιπέδου γραμμής
-Έλεγχος στάθμης σήματος αποστολής/λήψης στο εμπρόσθιο τμήμα
-Τροφοδοτούμενο από την τηλεφωνική γραμμή
-Εσωτερικό buzzer on/off
- 1U Πλαίσιο 1/2
D&R's newest Telephone Hybrid-1 is an interface between a standard telephone line and a mixing console. Its purpose is to enable to record or broadcast a conversation between a caller and a presenter in an easy way.
Superb audio separation between in and outgoing signals are achieved by carefully designed internal circuitry. It is a problem solver for changing two wire communication into a four wire system with separate in and outputs.
Telephone hybrids provide the interface between professional audio equipment and the public telephone network.
They provide protection for your equipment and the public telephone lines, allowing for varying line signals and line conditions. Automatically canceling out the unwanted signal they also facilitate two-way communication down a single telephone line.
Each hybrid has a telephone line connection, a handset connection and separate connectors for audio input and output from a broadcast mixer, or other professional audio source.
A large proportion of D&R hybrids are used in radio and television broadcasting applications allowing external callers to be connected to the studio mixing console. Most of the other units are supplied to communication operations allowing extremely effective conversion between 4-wire audio circuits and standard telephone lines.
Specification
Output: balanced mic level -20dB. Input: Line level 0 dBu balanced. R/C balance: fully adjustable separation to more than 30dB.
C-BALANCE :12 pole rotary switch to select the optimum side tone attenuation.
R-BALANCE: Internal potentiometer to adjust for optimum side tone attenuation.
TO CALLER: Switch to temporarily connect the line (wall) connector to the Phone connector (appliance) to be able to dial and make a connection.
ON-LINE CONNECT: Line connect switch to connect and disconnect calls from the telephone line |
DBX-1074
4 ch noise gate με δυνατότητα λειτουργίας σε ρυθμιζόμενο εύρος
συχνοτήτων XLR in/out, insert points.
- Four independent channels of gating
- Independent key filtering
- Independent Threshold and Release controls
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Stereo Coupling mode
- Switchable +4dBu or -10dBv operation per channel
| Input Connectors | XLR (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | 40dB: Typically >55 dB at 1 kHz | | Key Input | Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm | | Output Connectors | XLR (Pin 2 hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 60 Ohm, unbalanced 30 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 200 kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 115 dB, unweighted | | THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Operating Voltage | 100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 30 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Unit Weight | 6.9 lbs. | | Shipping Weight | 9.3 lbs. |
|
Manual
Axel Compact telephone hybrid BoxTel MKII
AXEL Compact telephone hybrid. Management of 1 wired PSTN / POTS line, electronically balanced input and output on XLR connector
Product Discription:
BoxTel MKII is an analogue telephone hybrid, designed to interface a telephone line with audio equipments. BoxTel MKII manages 1
POTS/PSTN line, whereas BoxTel GSM manages 1 GSM line to establish telephone connections where wired lines are not present.
A powerful internal microcontroller completely manages both BoxTel MKII and BoxTel GSM, allowing the configuration of the operating modes
via software. The internal microcontroller provides further functions such as adjustment of the line impedance according to the region,
visualization of the Send/Receive audio levels on the front leds, line detecting presence of a telephone line, buzzer with adjustable level,
AutoHook - automatic line hooking and answering after a certain number of rings. While BoxTel MKII is operative, its possible to exclude or
keep connected in parallel an external telephone set (Tel.Set).
The backlit Hook/Ring button on the front panel allows a quick management of the phone calls; each time a telephone call is incoming the
BoxTels Hook/Ring button starts to flash, by pressing it the operator answer the phone call. BoxTel MKII has the Line Detecting function,
which makes the Hook/Ring button switch on in presence of a telephone line.
BoxTel MKII and BoxTel GSM are devices equipped with an internal power supply enabling great audio performance: two separate
Send/Receive front potentiometers manage the audio level, with a total range of +/- 15dB. The input sensitivity is set at 0dBu while the
maximum output level is greater than +20 dBu.
The audio connections are separated for Send/Receive and are available over XLR electronically balanced connectors. A RJ11C connector
allows the telephone line connection (Tel.Line) and one more RJ11C connector performs the connection to an external telephone set (Tel.Set).
A GPIO port with optocouplers and open collector is provided to establish remote connections between BoxTel MKII and BoxTel GSM and
mixing console. It is possible to connect directly the Telco module of an Oxygen4, Oxygen5 and Oxygen7 console with BoxTel MKII/BoxTel GSM
by using a simlpe Pin-to-Pin cable. Internal universal power supply 90-264Vac/47-63Hz to operate worldwide.
Thanks to all of their features, BoxTel MKII and BoxTel GSM represent the telephone hybrids with the best quality/price ratio available on the
marketplace. BoxTel MKII and BoxTel GSM occupy ½ rack unit - LxHxD 22x5x13cm.
HIGHLIGHTS:
- Compact telephone hybrid
- 1 POTS/PSTN or GSM DualBand telephone line
- Send/Receive audio levels control and visualization
- Backlit Hook/Ring button
- Software configuration
- Phone call auto-answer feature
- International selection of the line impedance
- Remote control
- Potentiometer levels and front panel control
- Analogue Send/Receive balanced over XLR
- 1 USB port
- GPIO to remotely control Telco N-1 modules
Technical Facts:
- Dimension LxHxD 22x5x13cm
- AC Rate 230Vac / 110Vac 50 Hz / 60 Hz 30VA
- Type of power supply Switching power supply, worldwide
- Weight ≈ 2500 gr
- Operating Temperature -5°C / +50°C
ANALOG INPUT MODULE (send) - Connectors: XLR, female - Electronically balanced
- Operative Nominal Level: 0 dBu
- Line Impedance 10 kΩ (Electronically balanced selectable) EMIsuppressed
- Distortion: less than 0.01% TDH+NOISE (0.0dBu 1Khz)
- Input Modes: Mono
ANALOG OUTPUT MODULE
(receive) - Connectors XLR, male - Electronically balanced
- Output Level 0dBu +4dBu +6dBu Max +20dBu
- Load Impendance 600 Ω
- Distorsion Less than 0.01% TDH+NOISE (0.0dBu @ 1Khz)
- Output Modes: Mono
TELEPHONE MODULE PSTN / POTS - Connectors LINE RJ 11C 6/4 socket
- Connectors SET RJ 11C 6/4 socket
- Bandwidth telephone line 100Hz 5kHz, -3dB @ 1 kHz
- Telephone line compliance ETSI TBR21, FCC Part68
- Isolation 3 kV
REMOTE INTERFACE - Digital Inputs GP In 2x GP In opto coupled. Only 1 is used as Hook
- Digital Outputs GP Out 2x GP Out Open Collector opto isolated. Only GPOut 1 is used as Ring
Technical Specification about BoxTel MKII GSM (Additional ) - TELEPHONE MODULE GSM Module
- Standard DualBand GSM 900/1800 Mhz Phase 2+
- Frequency GSM 900: (Tx) 890 915 Mhz / (Rx) 935 960 Mhz
- GSM 1800: (Tx) 1710 1785 Mhz / (Rx) 1805 1880 Mhz
- Sensitivity -104 dB
- Channel bandwidth 200 kHz
- Maximum consumption 0.25 W / 0.5W
- Stand-by consumption
- Sensitivity -104 dB
- Dial tone frequency 450 Mhz Standard
- Environment noise
- Transmitting Power
- External Antenna 2.5 dBi omnidirectional with 1mt standard cable
- External power supply unit Input: 100-240 Vac Output: 12 V 500 mA
- External Antenna connector SMA
- Total rechargeable battery time 6 h
- PSTN / POTS connector RJ 11C 6/4 socket
- Operating temperature 0°C ≈ +45°C
- EN COMPLIANCY for GSM Modul EN 60950-1
- EN 301 489-1/-7
- EN 301 511
|
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor. Ανιχνεύει αυτόματα τους μικροφωνισμούς και τους εξαφανίζει. Διαθέτει επίσης low cut filter, phantom power, balanced in/out.
Χαρακτηριστικά:
Μονοκάναλο feedback destroyer (αντιμικροφωνικό) με ενσωματωμένο προενισχυτή μικροφώνου, delay line, noise gate και compressor
Αυτόματα ανιχνεύει και εξολοθρεύει 8 συχνότητες μικροφωνισμών
Ultra low noise mic/line είσοδος με gain control και +48V phantom power τροφοδοσία για πυκνωτικό μικρόφωνο
Delay line μέχρι 2,5 sec και με ρύθμιση μέτρων ποδιών και msec
Noise gate με αυτόματες και manual ρυθμίσεις
Αυτόματο compressor
Low cut filter με ρύθμιση συχνότητας
Είσοδος – έξοδος σε balanced JACK 6,35 και XLR
Frequency response: 10H – 21KHz
Noise: 92dB (line), 89dB mic
THD: 0.007%
Μετατροπείς: 24bit Sigma-Delta, 64/128-times oversampling
Η συσκευασία περιλαμβάνει: fbq100, users manual
Τροφοδοσία: AC 220V / 50Hz
Διαστάσεις: 56 x 88 x 132 mm
Βάρος: 380 gr
|
VIRTUALIZER 3D FX2000 - Υψηλής απόδοσης 3D Multi-Engine Επεξεργαστής εφέ.
• 71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
• Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
• Awesome modulation, dynamic, psychoacoustic and EQ algorithms
• Authentic amp simulation, distortion and special effects
• 11 effect combinations with selectable serial / parallel configuration
• Up to 7 adjustable parameters plus 2-band EQ per effect
• 24-bit A/D and D/A converters with 64/128-times oversampling
• True stereo processing for realistic channel separation in stereo image
• 100 factory presets plus 100 user memory locations
• Extensive MIDI implementation
• Accurate LED level meters for perfect level setting and optimum performance
• Servo-balanced XLR and ¼'' TRS inputs and outputs
The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.
The FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.
• Reverbs: Cathedral - Gold plate - Small hall - Studio - Concert - Stage - Spring & Reverse Reverb - Ambience and more...
• Delays: Stereo - Tape Echo - Ping Pong and more...
• Modulation and Pitch Shifter FX: Stereo/Vintage/Jet Stream Flanger - Stereo/Analog/Vintage/Ultra/ Chorus - Stereo/Vintage/Dual Phaser - Rotary - Pitch Shifter - Vibrato and more...
• Dynamic FX: Compressor – Expander – Gated Reverb – An. Compr/Lim. — Ultramizer – Denoiser – De-Esser and more...
• Psychoacoustic FX: Exciter – Enhancer – Stereo Imager and more...
• Filter/EQ FX: Auto/LFO Filter – Parametric/Graphic EQ.
• The FX2000 is also equipped with distortion, amplifier and speaker simulation including Vocal/Tube distortion, Guitar Amp and more...
• Special FX:Vinylizer - Sampler - Vocoder - Voice Canceler - Resonator.
|
Description
The alphaton Feedback-Controller FC-100 is a revolutionary product for every microphone
application including wireless types. It can provide effective feedback control to any sound
reinforcement situation. It can also eliminated string feedback in guitars and bass instruments
which are equipped with piezo or condenser pickups.
The FC-100 provides 6 to 10 dB of feedback protection by analysing the incoming signal,
detecting the presence of feedback and then notching out the feedback frequency.
The FC-100 relieves the sound engineer automatically. It works dynamically and eliminates a
feedback signal before it can grow into a peak. Internally a discriminator circuit detects the
presence of regenerative feedback and triggers the automatic equaliser to insert a notch where
the feedback peak is coming up. This normally prevents other peaks from developing but if they
do, the process is repeated at high speed, thus keeping feedback under control.
Technical Data
In- and Outputs transformer balanced
max. Inputlevel + 3 dB
Gain (RS=200 Ohm, RL=2kOhm) 0 dB
Frequency Response 20 Hz ... 20 kHz, +/- 1,5 dB
Feeback Cancellation 6 ... 10 dB
Power Requirement 30 ... 48 V Phantom
Current drain ca. 8 mA
External Power Supply 9 ... 20 V DC, 3,5 mm jack, tip +
Housing Aluminium Diecast
Weight 285 grams
Dimensions 112 x 60 x 32 mm |
Αξιολογήσεις
Δεν υπάρχει καμία αξιολόγηση ακόμη.