LD SYSTEMS LDXS200 Ενισχυτής Ισχύος 2x100W @ 4Ohm

The XS200 is an extremely compact, dependable Class D power amplifier with an output of 100W per channel at 4 ohms and a transmission range of 20Hz - 20kHz. With just 1U and a weight of 3kg, it is conceived for all professional applications in which ease of transport or space is important, whether mobile, in installations or at home, since no fan is required.

The XS200 is protected against short-circuiting, DC, overheating, and overloading and has a soft-start delay. The amplifier features XLR, RCA and jack input connectors, with Speakon-compatible sockets and screw terminals as outputs. Slide switches on the rear panel let you select the mode of operation and gain and activate the limiter and the ground-lift function for eliminating ground loop hum. LEDs indicate power, signal, clipping, triggering of the protection circuit, and the mode of operation. The XS200 impresses with its high dynamics, impulse fidelity, and transparent sound.

• Type: 2-channel
• Output power (1 kHz @ 4 ohms): 2 x 100 W
• Output power (1 kHz @ 8 ohms): 2 x 50 W
• Output power (1 kHz @ 8 ohms, bridged mode): 200 W
• Circuit concept: Class D
• Frequency response: 20 - 20,000 Hz
• THD:
• Voltage gain: 30 dB / 26 dB / 24 dB
• Input sensitivity: 0.77 V / 1.1 V / 1.4 V (passed)
• Protection: Soft-start, short-circuit, DC, overheating, overvoltage
• Controls: On/Off, Volume, Mode (bridge / parallel / stereo), Ground Lift, Limiter, Gain
• Indicators: Power, Signal, Clip, Protect, Mode (bridge / parallel)
• Line input connectors: 2 x XLR, 2 x 6.3 mm jack, chinch
• Speaker output connections: 2 x Speakon-compatible, 2 x terminal post
• Power supply: switching power supply
• Power Consumption @ Full Load: 240 W
• Operating voltage: 115 V AC / 230 V AC (switchable)
• Width: 482 mm
• Height: 44 mm
• Depth: 244 mm

The high efficiency of the ED series enables maximum efficiency with low heat generation.

A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.

Τελικός ενισχυτής 2U ισχύος 2 Χ 300 Watt/4Ω με απόκριση συχνότητας 20Hz - 20KHz. Βάρος 15 Kg. Διαθέτει ρύθμιση ευαισθησίας εισόδου (0,775V/1,0V/1,44V), Limiter και φίλτρα Low pass & High pass για σύνδεση με sub ή δορυφόρο. Διαθέτει εισόδους balanced XLR/JACK και εξόδους ηχείων σε Speakon & Binding post.

XB Series - Intelligent Power

Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XB 400:  2x 200 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.025%
Signal-to-Noise Ratio:  < 103 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  500 @ 4 Ohm
Cooling:  2x fan (temp. reg. variable speed)
Weight:12 kg /(26 lbs)                                    
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).

XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.

• Rack mount stereo powered monitor speaker system
• New AES/EBU digital input
• lndependent MUTE function
• Sophisticated control panel section
• Ideal where space is at a premium

• Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
• AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
• Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
• Independent MUTE function by holding down CH SEL key for a while.
• Auto Mute when powering on*.
• D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
• Multi-voltage power supply.

Speaker Section

• Unit: 110 x 40mm cone type, magnetically shielded, x 2
• Impedance: 8 ohms
• Output SPL: 84 dB/W (1m)
• Frequency response: 200Hz to 20kHz

Amplifier Section

• Rated output power: 10W or more (8 ohms, 1kHz)
• Residual noise: -60 dBV or less (DIN AUDIO)
• Distortion: 0.5% or less (10W / 4 ohms, 1kHz)

Digital input

• Connector: XLR-3-31 type
• Digital input Format: IEC60958 (AES/EBU)
• Digital inputSampling frequency: 44.1kHz to 96 kHz
  

Analog input

• Connector: XLR / 1/4" combi-jack
• Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
• Analog input Input impedance 10k ohms or more

Phones

• Connector: 1/4" stereo jack
• Applicable load imp. 8 ohms or more
• Rated output power 20mW + 20mW (32 ohms, 1kHz)

General

• External dimensions: 430(W) x 44(H) x 282(D) mm
• Weight: Approx. 3.5kg
• Power requirement: 100 - 240V~, 50/60Hz
• Power consumption: 10W