DBX 1074 NOISE GATE USED (Made in USA)

• Four independent channels of gating
• Independent key filtering
• Independent Threshold and Release controls
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Stereo Coupling mode
• Switchable +4dBu or -10dBv operation per channel

  Input Connectors	XLR (Pin 2 and tip hot)
  Input Type	Electronically balanced/unbalanced, RF filtered
  Input Impedance	Balanced > 50 kOhm, unbalanced >25 kOhm
  Max Input	> +22 dBu balanced or unbalanced
  CMRR	40dB: Typically >55 dB at 1 kHz
  Key Input	Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm
  Output Connectors	XLR (Pin 2 hot)
  Output Type	Servo-balanced/unbalanced, RF filtered
  Output Impedance	Balanced 60 Ohm, unbalanced 30 Ohm
  Max Output	> +22 dBm balanced, > +20 dBm unbalanced
  Bandwidth	20 Hz to 20 kHz, +0/-0.5 dB
  Frequency Response	0.35 Hz to 200 kHz, +0/-3 dB
  Noise
  Dynamic Range	> 115 dB, unweighted
  THD+Noise	0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
  Interchannel Crosstalk
  Stereo Coupling	True RMS Power Summing
  Operating Voltage	100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
  Power Consumption	30 Watts
  Fuse	100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
  Power Connector	IEC receptacle
  Unit Weight	6.9 lbs.
  Shipping Weight	9.3 lbs.

   

GENERAL DATA
Power Supply 220 / 110V 25 VA
Dimension 434x351x44mm (1 rack unit)
Weight » 4 Kg
MEETING INTERFACE IN / OUT
Connector DB 9 female
Nominal in / out audio level 0 dBm
Input impedance 600 W / 10 KW (selectable)
Output impedance 100 W
* nominal line level: - 6 dBm
** it can vary depending on characteristics of telephone line
All measurements are intended at 1 kHz.
AUDIO PROGRAM IN / OUT
Connectors XLR, electr. balanced
Input impedance 600 W / 10K W (selectable)
Output level * - ¥ ¸ + 16 dBm
Output impedance 100 W
Noise on Receive output 2-Wire separation £ 25 dB**
4-Wire separation £ 70 dB
2-WIRE SECTION
Connector RJ11
Nominal input level - 6 dBm
Nominal output level - 6 dBm
Compensation mode Electronic, transf. decoupled
Impedance 600 W
4-WIRE SECTION
Connector Terminal block
Impedance 600 W
Nominal TX level 0 dBm
Nominal RX level 0 dBm

Features
Four Independent Compressor Channels
Channels 1 and 2, 3 and 4 are stereo linkable
7 LED Gain Reduction metering
Balanced XLR Inputs and Outputs
Sidechain Insert points
Intuitive, user friendly layout
Flawless performance
 
The sheer amount of effects and signal processors necessary for today's standards
of audio production puts a great strain on the available space in equipment racks,
both in the studio and on the road.So, ARX would like to introduce the ARX Quadcomp.
An all-new upgrade of the classic award-winning ARX Quadcomp?, the very first four
channel 1 RU compressor.You?ll notice that we haven?t strayed very far from our
original design concept. The Quadcomp  is still four variable ratio Compressor/ Limiters
neatly housed in a compact all steel 1 RU package. However, all new low noise/low
distortion circuitry, better metering plus XLR inputs and outputs put the Quadcomp
in a class of its own.
More Control, Less Space
On the front panel, each channel has the 'industry standard' individual controls for Threshold,
Compression Ratio and Output, plus a new 7 LED Gain Reduction display for accurate visual
indication of the amount of gain reduction being applied to the program, and an IN/OUT
hardwire bypass switch.In addition to this, each channel has a blank numbered panel to write
on for easy confirmation of compressor assigns.
Precision Circuitry
Internally, each compressor uses Class A VCAs and true 2 pole averaging RMS/DC converters
for low distortion and accuracy, plus program dependent attack and release time, which
automatically determines optimum compressor response.
Balanced Inputs and Outputs
The rear panel has true differential Balanced XLR Inputs and Outputs for each compressor.
Each compressor has a TRS jack Sidechain access insert point, for frequency sensitive
compression, De-essing, etc. in conjunction with an external equalizer (such as the ARX EQ260).
Compressor pairs 1 and 2, 3 and 4 also have rear panel mounted Stereo Link switches for accurate
stereo tracking. When switched IN, the first channel becomes the master and controls all the functions
of the second except Output gain.
Universal AC Power
AC power range is switchable 100 to 120V, or 220 to 240V, and is connected to the unit via
a standard IEC connector, with built-in fuse and voltage switch.
Whatever the application ? Channel insert, Bus insert, Master Outputs, Monitor outputs,
Crossover outputs, the Quadcomp II?s unique High Density design, precision Low Noise circuitry
and clean uncluttered layout make it a truly useful audio tool for all applications.

T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 20dB
CMRR >50dB, 20 Hz?20 KHz
Output Impedance
Balanced 300 ohms Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz-20KHz ±0.5dB
Signal to Noise ratio
-93 dB Unweighted, -98 dB ?A? weighted
Distortion .015% THD @ 0dB,1KHz
Dynamic Range 108 dB
Attack and Release Times Program dependent
Metering
7 LED display: ?1, 2, 3, 6, 12, 18, ?24 dB
Sidechain Insert Impedance 10 Kohm
Power Requirements
100/120 V AC or 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input Connector type Balanced XLR
Output Connector type Balanced XLR
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
7 LED Gain Reduction display
Marker panel for labelling compressor assigns
Stereo link status LEDs
Rear Panel Connectors
Input and Output balanced XLR connectors
TipRingSleeve Sidechain insert connectors
Channels 1 and 2, 3 and 4 Stereo link switches
IEC AC mains connector with inbuilt fuse and
voltage change

Features
Unique High Density design puts SIX gates in
minimum rack space
Intuitive, 'user friendly' layout
Balanced Inputs and Outputs
Fast, low noise opto-coupler circuitry
Sidechain/Key Input points on each channel
Hardwire Bypass switch on each gate
Flawless performance in any audio environment

The sheer amount of effects and signal processors required for today's
standards of audio production puts a great strain on the available space
in equipment racks, both in the studio and on the road.
So, in order to give engineers more control in less space, we've created
the ARX Sixgate; Six full function noise gates neatly housed in a compact,
all steel 1 RU package, without sacrificing features or quality.
Why Six gates?
Research shows that the majority of noise gates get used on drum kits,
which means using typically 5 to 6 gate channels. Compare this to the
two or maybe 4 channels that most other units have, and you'll see the
reason for the Sixgate's success.And, by using a minimalist approach to
drum gates, the ARX Sixgate has enough gates left over for backing vocals
and other instruments.
Industry Standard controls
Front panel controls for each gate consist of the 'Industry Standard' controls
for Release, Depth and Threshold, plus Red and Green LED displays to indicate
Gate Open or Closed status, and an IN/OUT hardwire bypass switch.
In addition to this, each gate has a blank panel to write on for easy confirmation
of gate assigns. No more pieces of masking tape stuck everywhere!
Ultra Low Noise
Internally, each gate has proprietary ARX ultra low noise high-speed opto-coupler
circuitry with program dependent Attack time, which tracks the incoming signal to
automatically determine optimum gate response.
Balanced Inputs and Outputs
The rear panel features true differential Balanced Inputs and Outputs for each gate,
on insulated TRS jack connectors.Each gate channel also has Individual Key Inputs/
Sidechain access insert points which can be used either for gate control by an external
signal, or for frequency sensitive gating (when used in conjuction with an external
equalizer such as the ARX EQ260).
Universal AC Power
AC power range on the Sixgate is a universal 100 to 120V or 220 to 240V, and is
connected to the unit via a standard 3 pin IEC connector, with built-in fuse and voltage
switch.
The Sixgate's unique combination of High Density design, intuitive 'user friendly' controls,
and clean uncluttered layout make it a truly useful audio tool for all applications.

T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance
Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance
Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 20 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise Ratio
Gate Closed: -95 dB Unweighted, -105 dB 'A' weighted
Gate Open, Depth Minimum: -93.5 dB Unweighted -98dB
'A' weighted
Distortion 0 .01% THD @ 0dB,1KHz
Dynamic Range 125 dB
Attack Time Program dependent using high-speed
opto-couplers
Release Time User variable
Input and Output Connector type Balanced Jack
Sidechain Insert Connector TipRingSleeve Jack
Sidechain Insert Impedance 10 Kohm
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions
19“Wide x 13/4“High x 6“Deep; 482 x 44 x 155mm

Front Panel Controls
Individual Release, Depth and Threshold controls
Hardwire bypass IN/OUT switch
Open/Closed gate status LED
Marker panel for labelling gate assigns
Rear Panel
Balanced Inputs and Outputs, on Balanced jack
connectors
Sidechain Insert/Key Input TipRingSleeve jack on
each channel
AC input connector, with voltage switch and fuse 

OPTIMOD-FM 5500 puts coveted five-band and two-band OPTIMOD processing into a single rack unit package and brings it to you at the most affordable price ever.

Quality sound is what 5500 is all about-sound that attracts audiences by providing a polished, professional presentation regardless of format and source material. Exceptional versatility allows you to adjust the processor's audio texture to brand your audio, knowing that the resulting signature sound will remain consistent, cut-to-cut and source-to-source. Branding builds businesses and no other processors have the consistency to brand your sound like OPTIMOD.

With the 5500, your signature sound is just a preset away. An easy, one-knob Less/More adjustment allows you to customize any factory preset, trading cleanliness against processing artifacts according to the requirements of your market and competitive environment. Full Control gives you the versatility to customize your audio further. And, if you're a hard-core processing expert, you can explore Advanced Control to tweak presets at the same level as Orban's factory programmers. This versatility makes the 5500 a superb choice for any format. Its five-band processing is ideal for any pop music format (even the most competitive and aggressive CHR), while phase-linear two-band processing yields ultratransparent sound for classical, classic jazz, and fine arts formats. Regardless of your choice, 5500's optimized technology ensures unusually high average modulation and coverage for a given level of subjective quality. Unlike many lesser processors, the 5500 handles speech particularly well. It's always clean, even when you process for loudness.

If you're concerned about latency because you need to feed live talent headphones off air, be assured that the 5500's ultra-low-latency (5 ms delay) processing will keep the most finicky talent happy. Or use optimum latency (15 ms delay) processing for the most competitive sound with delay that's still low enough to satisfy most any talent.

The 5500 can also be used as a superb stand-alone stereo encoder with latency as low as 2 ms and full overshoot limiting in both the left/right and composite baseband domains.

When used in this mode, the 5500 must be driven (usually via an STL) by a full-featured FM audio processor (like Orban's 8600) that incorporates pre-emphasis aware HF limiting and peak control. In both modes, the 5500's stereo encoder helps deliver a transmitted signal that's always immaculately clean and perfectly peak limited, with full spectral protection of subcarriers and RDS/RBDS regardless of the amount of composite limiting.

It is the ideal choice for network broadcasters who process with Orban's flagship OPTIMOD-FM 8600 at the network origination point and who need a processor at every transmitter to eliminate STL overshoots (using the 5500's stand-alone stereo encoder mode) and/or to process local insertions while also eliminating network STL overshoots (using the 5500's audio processor / stereo encoder mode). Moreover, the 5500's two modes make it easy for large government and network broadcasters to manage its inventory of spares because any 5500 can be used as a stereo encoder with or without audio processing.

Available in both modes, the built-in, defeat-able ITU-BS412 multiplex power controller allows the 5500's output to meet even the most stringent European government regulations.

A 10 MHz frequency reference input allows the stereo pilot tone frequency to be locked to GPS or another high-accuracy frequency standard. This improves the performance of single-frequency networks in areas where coverage of the transmitters overlaps.

The 5500's built-in stereo encoder, AES/EBU digital inputs and outputs, and analog I/O permit hasslefree interfacing to any broadcast plant, whether the 5500 is located at the studio or the transmitter. Tight band limiting to 15 kHz means you can use any uncompressed digital STL to pass 5500- processed audio from studio to transmitter without compromising on-air loudness - there's no need to use STL's having 44.1 or 48 kHz sample-rate.

The stereo encoder's stereo sub-channel modulator can operate in normal double sideband mode and in an experimental compatible single sideband mode (SSB/VSB) that is offered to enable users to compare and assess the two modes.

Analog Fallback to Digital control that allows Silence Sense to switch the active input from Analog to Digital if silence is detected in the analog input signal but not on the digital input signal. This function works vice versa as well on both analog and digital AES input. The silence sense parameters apply to both simultaneously and both detectors are available to drive the 5500's tally outputs and sending SNMP Traps/Alerts.

If you want to locate the 5500 away from the studio, you'll be pleased by its three separate remote control ports - GPI contact closures, RS232 serial and built-in Ethernet for TCP/IP networks. The serial and Ethernet ports are supported by the supplied 5500 PC Remote Control application. This Windows® 2000/XP/Vista/7/8 application allows you to do even more with the 5500 than you can do through its front panel, making remote control a pleasure.

5500 PC Remote software allows you to access all 5500 features and allows you to archive and restore presets, automation lists, and system setups (containing I/O levels, digital word lengths, GPI functional assignments, etc.)

Built-in clock-based automation lets you automatically day-part the processing. You can control many other 5500 operating parameters too.

The 5500's feature set fully exploits the processor's DSP and computer-based control architecture. To ensure absolute accuracy, you can automatically synchronize the clock to an Internet timeserver. It has a cool-running, energy-efficient switching power supply and uses the latest dual-core DSP chip technology from Freescale Semiconductor.