APEX ARGOS SOUND LEVEL CONTROLLER

With its concealed, authority seal-able and straightforward set-up controls, you'll be able to quickly protect hearing and the environment, either on the road or in fixed installations. The Argos front panel clearly displays the level reduction applied.

You can choose between different 3 modes of operation: use the measurement microphone provided, the line inputs or the power amplifier inputs as level measurement reference.

Argosʼ unique servo-loop circuitry will preserve the whole audio signal quality and the entire dynamic range of the sound programme. Its unique silence detector makes it an indispensable tool for live music performance as well as interrupted recorded music, it will prevent pumping artefacts when the signal returns.

Configuring the Argos in fast mode and connecting it directly to your power amplifiers output, in parallel with the speakers, will protect your sound system against dangerous DJs, hard-rockers and extensive repair bills.

Use the Argos together with the Apex Hera, they will be your neighbours dream team !
Application

    Directive 2003/10/EC "Noise at work“
    fixed installation: bar, theatre, concert venue, ...
    on the road: mobile DJ, live concert, ...
    sound or broadcast studio to limit the sound level on monitor system

Features

Key features

    affordable price
    unique servo loop circuit allowing smooth operation (no compression or limiting artefacts in sound)
    proven to be most natural sounding leveller
    unique silence detection function with gain reduction hold circuit (avoiding pumping effect when sound comes back after a silence), ideal for live band
    3 sound level detection modes: microphone, line or loudspeaker
    direct connection to power amplifier output and fast operation mode allowing use as speaker protection
    may work independently or combined with the Apex Hera to increase the functions and capabilities

General features

    choose between smooth and fast operation
    sound level and gain reduction indicators
    concealed and authority seal able set-up controls
    the 'Test' button on front panel confirms the correct installation by muting the audio signal
    choice between A-weighted and C-weighted filters
    built-in pink noise generator for calibration
    balanced 3-pin XLR and RCA (cinch) connectors at inputs and outputs

Specifications

Input / Output
- Electronically balanced / floating
- RF suppression with LC filters
- Maximum level: +24 dBm
- Impedance: 10KOhm / 100 Ohm
XLR-3 type connector
connections: 1 ground, 2 hot (+), 3 cold (-)

Audio Specifications
- Frequency response: 10Hz - 40kHz + 0,2 dB
- TND + Noise:

Providing 48-bit filter algorithms, 24-bit AD/DA conversion and a dynamic range of 115 dB, the DSP 244 sets new standards for digital loudspeaker controllers and processors. The DSP 244 is an universal Digital Sound System Processor that provides 2 inputs and 4 outputs; plus internal summing of the inputs 1 and 2. Via matrix it is possible to assign the outputs to any input or to the sum of the inputs. It is further possible to establish the following configurations: Stereo or Dual 2-Way systems, 3-Way + Direct and 4-Way systems, each with Mono Subchannel, but also full range systems. High and low-pass filters are provided for the frequency crossover functions in all operation modes. The selection includes Linkwitz-Riley, Butterworth and Bessel type filters with switchable slopes between 6, 12, 18 and 24 dB/oct. A huge number of additional filters offers extremely flexible correction of the frequency response. Each input incorporates a 5-band equalizer, allowing to assign high and low-pass, high and low-shelving or parametric peak-dip filters to its individual filter sections. Next to the frequency crossover filters, four additional filters are employed in each output channel, which also can be set to work as high or low-pass, high or low-shelving filters, parametric peak-dip filters, or all-pass filters. Additional filtering is provided through 2. order high-passes for the realization of B-6 alignment, or special LPN-filters (Low-Pass Notch filters) for correcting the frequency and phase responses of optimally vented woofer cabinets. Each channel additionally provides a delay, a polarity switch, a programmable level control and a digital compressor / limiter while the master delays are located in the input channels. Datasheets / ManualsBrochure (309KB)

Mains voltage 90 - 250 V AC / 50 - 60 Hz Power consumption 20 watts Safety class I Inputs 2 x XLR IN, electronically balanced, transformer optional available 2 x XLR OUT (Direct Out) Input voltage (nominal) 1.55 V / + 6 dBu Max. input voltage 24.5 V / + 30 dBu Input impedance 20 kohms Common mode rejection > 40 dB AD-conversion 24-bit, Sigma-Delta, 128 times oversampling, linear phase Outputs 4 x XLR OUT, electronically balanced Output voltage (nominal) 1.55 V / + 6 dBu Max. output voltage 8.7 V / + 21 dBu Output impedance

Based on a two-in, six-out topology, the DC-One is designed primarily for users of small-to-medium sized sound systems in both mobile and installed applications. While the unit is an all-new development based on a powerful SHARC processor, it is 100 percent compatible with all settings from other Electro-Voice signal processors. A large part of DC-Oneʼs development was aimed at ensuring that users can easily handle its serious digital horsepower and high-end audio performance. Free. PC-Editor software is available, or the DC-One can be operated via the front panel.   A/D Conversion    24-Bit Delta-Sigma
A/D Conversion    24-bit/sigma-delta (linear phase) 128 times oversampling
Analog Inputs    2 XLR (Electronically Balanced), 2 XLR THRU OUT (Electronically Balanced)
Analog Outputs    6 XLR (Electronically Balanced)
Control Protocol    Front Panel USB Connector
D/A Conversion    24-bit/sigma-delta 128 times oversampling
D/A Conversion    24-Bit Delta-Sigma
Data Format    24-Bit
Digital Inputs    1 XLR AES/EBU (2 Ch)
Dynamic Range    111 dB (unweighted, band limited 22 Hz - 22 kHz)
Electronics Type    Processor
FIR-Drive    No
Frequency Response    10 Hz - 22 kHz (±0.5 dB)
Input Impedance (Balanced)    10 kΩ
Internal Processing    32-Bit Floating Point
Mains Voltage    100-240 VAC
Maximum Input Voltage    8.7 V / +21 dBu (Without -6 dB Analog Pad Engaged)
Maximum Output Voltage    8.7 V / +21 dBu
Nominal Input Voltage    1.23 V / +4 dBu
Nominal Output Voltage    1.23 V / +4 dBu
Output Impedance (Balanced)    50 Ω
Power Consumption    25 W
Sample Rate    48 kHz
THD+N    < 0.01% (band limited 22 Hz - 22 kHz)
Height    1RU 44.45 mm (1.75“)
Width    482.6 mm (19“)
Depth    355.6 mm (14“)
Weight Net    4.6 kg (10.14 lbs) 

The Soundweb London BLU-160 offers configurable I/O, configurable signal processing and a high bandwidth, fault tolerant digital audio bus.

The BLU-160 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a "drag and drop” method of configuration provide a simple and familiar design environment.

This processor features a low latency, fault tolerant digital audio bus of 256 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the distance between devices to over 40km.

Four card slots which accommodate analog inputs, analog outputs, digital inputs and digital outputs in banks of four facilitate many different device I/O configurations.

Analog Input Cards provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel. Digital Input Cards and Digital Output Cards process AES/EBU and/or S/PDIF audio and offer a variety of clocking and syncing options. (Further information about the I/O cards can be found on dedicated datasheets)

Phantom Power, Sync, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. Device-specific information such as Device Name, Device Type, Firmware Version Number, Time, IP Address and Subnet Mask is available from the front panel display. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.

12 Control Inputs and 6 Logic Outputs allow the BLU-160 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.

The BLU-160 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.

• Four Input / Output Card Slots
• Configurable Inputs / Outputs
• Analog Inputs (with Phantom Power per Channel)
• Analog Outputs
• Digital Inputs (AES/EBU and S/PDIF)
• Digital Outputs (AES/EBU and S/PDIF)
• Configurable Signal Processing
• Rich Palette of Processing and Logic Objects
• 256 Channel, Low Latency, Fault Tolerant Digital Audio Bus
• Clear Front Panel LED Indication
• Informative Front Panel Display
• Bi-Directional Locate Functionality
• 12 Control Inputs and 6 Logic Outputs for GPIO Integration
• Soundweb London Interface Kit for Third Party Control System Integration (Documentation)
• HiQnet Device
• Configuration, Control and Monitoring from HiQnet London Architect

With 6 inputs and 4 outputs the dbx ZonePro? 640 and 641 provide flexible signal routing,
powerful DSP processing and multiple control interfaces for Commercial Audio applications.
Designed to offer superior system sonic performance and flexibility, the 640/641 deliver the
highest quality tools available. Even the input and outputs connectors were chosen for their
standard usage and reliability. The ZonePro products offer Euroblock connectors for balanced
signals and RCA connectors for interfacing with consumer equipment often used in commercial
applications; there is also a simple analog input buss that allows inputs to be sent from one
unit to the next for unit and job scalability. The 640 and 641 provide every necessary processing
tool, from the input processing like gain control and EQ available on all inputs to highly sophisticated
and specific functions such as selectable paging microphone processing including Gating,
De-Essing, Auto Gain Control, Compression and Feedback Suppression. The heart of the
ZonePro products is the Routing module that provides of course Primary Source Selection
but also Source Ducking for Paging and Priority Override. The outputs also offer a wealth of
processing designed for commercial applications like our patent-pending AutoWarmth? function
that was co-developed with JBL to provide natural low frequency extension at any signal level.
Each output also offers EQ, Bandpass and Crossover filters, Limiting and Delay for system
optimization. With the ZonePro? every tool is at your disposal to maximize the response of
your system.
Beyond processing, the ZonePro? products offer multiple forms of control to further extend the
versatility of your system. From easy-to-use wall panel Zone Controllers for standard end-user
functions like source select and volume control to advanced system control including a built-in
Real Time Clock that can provide programmable system changes throughout the day or week.
For system setup and monitoring the ZonePro Designer software provides an intuitive interface
and a speedy setup Wizard for configuring and editing all system parameters.

The ZonePro? 640 and 641 will take your Commercial Audio system to the next level with advanced
processing, versatility and control.

? Advanced Feedback Suppression (AFS?)
? Autowarmth?
? Auto Gain Control
? Compression
? Limiting
? Noise Gating
? Notch Filtering
? Bandpass and Crossover Filters
? Parametric EQ
? Security Lockout
? Wall Panel Control
? RS-232 Control
? Windows? 2000 and XP GUI
? IEC, UL and CSA Approvals

Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.

NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.

NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.

Specifications:

Network Connectors:
   * Nomadlink Out: EtherCon housed RJ45
   * Nomadlink In: EtherCon housed RJ45
   * Ethernet rear-panel: EtherCon housed RJ45
   * Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
   * One Voltage sensing input: Two pole Phoenix
   * Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
   * Front operation locked: Yellow LED
   * Fault warning: Red LED
   * Amplifier subnet muted: Red LED
   * NomadLink network connected/activity: Blue LED
   * Ethernet connected: Orange LED
   * Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption: Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)