| Content | The DAP CM-1 is a thin model condenser-microphone that comes with a cardioid and omni element. Depending on the application or personal taste the element can be exchanged. The CM-1 is ideally suited as a microphone for recording live ambient, drum overhead or acoustic instruments.
Type: Condenser
Freq. response: 30 Hz - 22 kHz (-3 dB)
Polar pattern: omni or cardioid
Sensitivity: 10 mV/Pa -40 dB -
Max. SPL: 132 dB
Impedance: 200 Ohm
power supply: +48V phantom
Connector: XLR male type
Net weight: 130 g
Dimensions: 23 mm (diameter) x L 150 mm
Accessories: microphone-clip |
The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern: Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
| The NT5 matched pairs are a masterpiece of small-diaphragm cardioid-
condenser microphone design.Intended for recording acoustic instruments,
drum overheads, cymbals and live performances, the compact externally
polarized mic employs a .5? capsule, an active J-FET impedance converter
with bipolar output buffer.
Finished in durable satin nickel, the NT5 is intended for either single or stereo
X/Y mic set-ups. The NT5 matched pairs comesupplied in a custom carry case
with windshields and mounts.
SPECIFICATIONS:
Acoustic principle: Externally polarised single diaphragm
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651: 78dB
Equvalent noise: Maximum spl: 143 dB @ 1% THD into 1k_
Sensitivity:
-38 dB re 1v/Pa ± 2 dB equivalent to 12mV/Pa where 1 Pa = 94dBSPL
Power supply voltage: P48 Supply (38V?52V), P24 Supply (20V-26V)
Current consumption: 4 mA, 2 mA,
Weight: 100g |
The ME 67 is a long gun microphone head designed for use with the K6 and K6P powering modules. A highly directional microphone, it can be used where the microphone must be placed at a distance from the sound source. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm (K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 343 mm
Weight : 100 g
| Technical specifications
| Polar pattern |
cardioid |
| Frequency range |
50 to 20,000 Hz |
| Sensitivity |
20 mV/Pa (?34 dBV) |
| Max. SPL |
125 dB (k=1 %) |
| Equivalent noise level |
21 dB-A |
| Signal/noise ratio (A-weighted) |
73 dB |
| Impedance |
600 ohms |
| Recommended load impedance |
>2000 ohms |
| Supply voltage |
9 to 52 V phantom power, requires DPA adapter (supplied with most Installation Modules) |
| Current consumption |
|
| Connector |
Discreet Acoustics Modular standard |
| Finish |
matte dark gray |
| Dimensions |
13.5 x 20 mm dia. (0.5 dia. x 0.8 in.) |
| Net weight |
5 g (0.17 oz.) |
| Shipping weight |
88 g (3.1 oz.) |
| Accessories (included) |
W 30 |
| NT3 - Versatile & Dependable
Stylish and modern, the NT3 is a studio and location workhorse. With both
48V phantom and internal 9V battery operation, this R?DE is at home anywhere.
Intended for studio, stage and location work, this versatile handheld or stand
mounted microphone incorporates a true externally polarized condenser (hyper-
cardioid polar response) transducer with an internal capsule shock mounting
system, and an ultra-low noise electronic circuit that has a high immunity to R.F.
interference. Incorporating a rugged welded and heat-treated mesh head and all
metal body. The NT3 is supplied in a zip pouch with a windshield, stand mount
and thread adaptor.
SPECIFICATIONS:
Acoustic principle: Externally polarised 19mm (3/4“) condenser
Directional pattern: Hypercardioid
Frequency range: 20Hz-20 kHz
Output impedance: 200?
Signal noise ratio din iec 651: > 77dB (per IEC268-15)
Equvalent noise: 123dB (per IEC268-15)
Power supply voltage: P48, P24, P12 phantom 9V battery
Weight without battery: 371g
Weight with battery: 680g |
Reviews
There are no reviews yet.