| Content |
Audio-Technicaʼs high-SPL BP892 MicroSet® offers the ultimate in low-profile, high-performance audio. Delivering clear and accurate sound in an inconspicuous package, the ultra-lightweight BP892 hooks securely behind either ear and can be worn for hours without fatigue. For maximum stability and comfort, the included AT8464 dual-ear microphone mount converts the MicroSet to a dual-ear-worn unit.
The microphone features a flat, extended frequency response and other outstanding performance specifications, resulting in extremely intelligible, natural audio for stage and television talent, lecturers and houses of worship. Protected by a highly durable Parylene coating, the new headworn mic is built to stand up to the rigors of day-to-day use.
Handles high sound pressure levels with ease
Extremely intelligible natural audio
Inconspicuous, lightweight headset with capsule diameter of just 2.6 mm is ideal for applications requiring minimum visibility
Ergonomic under-ear design—flexible, lightweight contoured loop hooks behind the ear for an ultra-secure, comfortable fit with or without glasses
Comes equipped with AT8464 Dual-Ear Microphone Mount that converts single ear-worn MicroSet to a dual-ear-worn unit for maximum stability and comfort
High-pass filter on power module provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Omnidirectional
Frequency Response: 20-20,000 Hz
Low Frequency Roll-Off: 80 Hz, 18 dB/octave (wired only)
Open Circuit Sensitivity: –49 dB (3.5 mV) re 1V at 1 Pa
Impedance: 250 ohms (wired only)
Maximum Input Sound Level: 135 dB SPL, 1 kHz at 3% T.H.D.
Dynamic Range: (Typical) 104 dB, 1 kHz at Max SPL (wired only)
Signal-To-Noise Ratio: 63 dB, 1 kHz at 1 Pa
Phantom Power Requirements: 11-52V DC, 2 mA typical (wired only)
Switch: Flat, roll-off (wired only)
Current Consumption: 0.1 mA typical at 5V (wireless only)
Voltage Range: 2.5-11V (wireless only)
Weight (Microphone): Microphone, boom & earpiece: 2.6 g (0.09 oz)
Weight (Power Module): 85 g (3.0 oz) (wired only)
Dimensions Microphone: 8.1 mm (0.32“) long, 2.6 mm (0.10“) diameter Boom: 98.4 mm (3.87“) long, 1.07 mm (0.04“) diameter
Dimensions (Power Module)@ 97.6 mm (3.84“) long, 18.9 mm (0.74“) diameter (wired only)
Output Connector: (Power Module) Integral 3-pin XLRM-type
Cable: 1.4 m (55“) long (permanently attached to microphone), 1.6 mm (0.06“) diameter, 2-conductor shielded cable with locking 4-pin connector (wired only)
Accessories Furnished: BP892: AT8539 power module (wired only); AT8464 dual-ear microphone mount; AT8440 cable clip; two AT8157 windscreens; two AT8156 element covers; moisture guard; belt clip (wired only); carrying case BP892-TH: AT8539 power module (wired only); AT8464-TH dual-ear microphone mount; AT8440 cable clip; two AT8157-TH windscreens; two AT8156-TH element covers; moisture guard; belt clip (wired only); carrying case
Audio-Technica Case Style: M31
|
Broadcaster - ?The Master of the Airwaves?
Like its name suggests this R?DE microphone was specifically designed ?ON-AIR?
applications where wide frequency response and low distortion are demanded.
Winner of the Radio World/US National Association of Broadcasters (NAB) ?What?s
Cool? award in 1998, the Broadcaster has become an industry standard when studio
sound quality is required for on air applications.
Utilizing an Australian designed and manufactured R?DE 1? externally biased condenser
transducers, the Broadcaster features a switch-able high pass filter to remove low frequency
rumble. A unique ?ON-AIR? LED indicator can be switched ?on? or ?off? by shorting contacts
on the 5 pin audio connector. This feature allows console operators to warn the ?Talent?
that the mic is live.
SPECIFICATIONS:
Features:
True condenser transducer On-Air indicator L.E.D. Ultra low noise
Cardioid polar pattern with high 180 rejection Voice tailored Low Cut
Filter Internal Pop Filter Rugged stainless steel body
Acoustic principle: Externally polarised 25mm (1?) condenser
Directional pattern: Cardioid
Frequency range: 20 Hz ~ 20 kHz
Output impedance: 40Ω
Signal noise ratio din iec 651:
>80 dB (1kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 114 dB (per IEC651, IEC268-15)
Power supply voltage: P48, P24 phantom
Weight without battery: 577g
Weight with battery: 1.3kg
Dimensions width: 167mm
Dimensions depth: 50mm
Dimensions height: 50mm
Maximum output voltage: +2 dBu (@ 1% THD into 1kΩ)
| OLED display (on receiver)
One button pairing
Three level gain control
AA battery or USB powered
Includes RØDE\'s broadcast Lavalier microphone
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres (over 100 yards). The RØDELink Filmmaker Kit provides everything you need to start shooting video wirelessly, including a receiver, transmitter and broadcast-grade lavalier microphone. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The lightweight transmitter (TX-BELT) can be fitted to a belt or clothing and features a locking thread to ensure the microphone connection is as secure as possible. RØDEʼs omnidirectional Lavalier microphone is included in the kit to provide the highest possible audio reproduction quality.
RØDELink Filmmaker Kit Specifications
Transmission type 2.4GHz Fixed Frequency Agile System
System dynamic range 112dB
Range (distance) 100m
Frequency range 35Hz - 22kHz
Maximum output level 1v Rms (2.8v P-p)
Max input signal level 1v Rms (2.8v P-p)
Max latency 4ms
Receiver (RX-CAM)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket - Dual Mono
Output impedance 300Ω
Dimensions 111mm X 65mm X 52mm
Weight 190gm
Transmitter (TX-BELT)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket
Output impedance 10kΩ
Dimensions 111mm X 65mm X 40mm
Weight 190gm
Lavalier
Acoustic Principle Pressure Gradient
Active Electronics JFET impedance converter
Capsule 0.10“
Address Type End
Frequency Range 60Hz - 18kHz
Output Impedance 3000Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 25dB-A
Weight 1.00gm
Dimensions 12.00mmH x 4.50mmW x 4.50mmD
Warranty 10 year warranty | RODE NT G8 Broadcast Quality RF-bias Shotgun Microphone
Based on RØDE's award winning NTG3, the NTG8 is a broadcast quality RF-bias shotgun microphone that exhibits increased directionality across a wide frequency response range. This makes the NTG8 the perfect microphone for film, television, sports and outdoor broadcasting, live performance, and any professional distance miking application.
Like the NTG3, the NTG8 features low self-noise, natural sound without colouration both on and off-axis, and RF bias technology to ensure that it is almost completely resistant to high humidity environments which could cause other condenser microphones to fail.
The NTG8 is finished in matte black and supplied with a specially designed shock mount (SM8) that is engineered to provide excellent handling noise isolation, cable management and versatile mounting options for the microphone. A rugged weatherproof aluminium cylinder is also included, providing ultimate protection for the microphone when in transport or storage. The WSNTG8 windshield completes the package, providing light environmental protection.
Acoustic Principle Line Gradient
Active Electronics RF Bias
Capsule 0.50“
Polar Pattern Hyper Cardioid
Address Type End
Frequency Range 40Hz - 20kHz
Output Impedance 2Ω
Maximum SPL 124dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 8.2dBu (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -20.0dB re 1 Volt/Pascal (97.50mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Power Options
(44-52V min 2.5mA)
Weight 345.00gm
Dimensions 559.00mmH x 19.00mmW x 19.00mmD
Output XLR | Broadcast sound quality
Low noise circuitry
Internal rechargeable lithium battery, supplying over 150 hours operation
Fully charged in under two hours via MicroUSB
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
MicroUSB cable included
Ten year extended warranty with online registration
Building on the popularity and acceptance of the RØDE NTG2, the NTG4+ features an all-new condenser capsule with low noise, high sensitivity and the convenience of on-board equalisation/level control via digital switching.
The NTG4+ is the very first microphone to feature an in-built battery that provides 150+ hours of operation with the convenience of USB charging.
Visit the NTG4+ feature page
NTG4+ Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom powerInternal battery
Weight 176gm
Dimensions 278mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration |
Clear, directional audio on the GO!
Compact and light weight by design, the VideoMic GO delivers clear, crisp, directional audio with incredible ease of use. Its tight pickup area focuses directly in front of the microphone and reduces other surrounding sounds, ensuring that your subject is isolated from distracting background noise.
The integrated Rycote® Lyre® shock mount isolates your microphone from bumps and vibrations that could otherwise interfere with your sound.
Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.
The VideoMic GO has no complicated switches or settings and is powered by your camera's external microphone input, requiring no batteries to operate, ensuring you never miss a great shot.
Acoustic Principle Line Gradient
Frequency Range 100Hz ~ 16,000Hz
Equivalent Noise 34dBA SPL (A - weighted per IEC651)
Signal Noise 60dB SPL (A - weighted per IEC651)
Power Required Plug-in power required (330uA @ 2.5V)
Dimensions 167mmL x 79mmH x 70mmD
Directional Pattern Super-Cardioid
Sensitivity -35dB re 1V/Pa (17.8mV @ 94dB SPL) ±2dB @ 1kHz
Maximum SPL 120dB (@ 1kHz, 1% THD into 1kΩ load)
Dynamic Range 96dB (per IEC651)
Output Connection 3.5mm stereo mini-jack
Weight 73g
|
Reviews
There are no reviews yet.