| Content |
The Feedback Destroyer Pro FBQ2496 from Behringer is a Feedback Suppressor that uses an ultra-fast feedback detection algorithm. The unit automatically and "intelligently" locates up to twenty feedback frequencies per channel and sets extremely narrow notch filters to attenuate them, leaving the remainder of the program material virtually untouched.
A "Set-and-Forget" default setting plus the Panic button, allows the FBQ2496 to be set up and running in no time. The auto mode continuously monitors the mix, resetting programmed filters automatically, while the manual mode allows individual setting of up to forty fully parametric filters with frequency, bandwidth and gain adjustment.
Open MIDI architecture provides for future software updates and flexible communication with other digital devices. With the unit's various modes, mastering just about any live sound situation is effortless, while the option to use it as a creative sound-shaping tool is always available.
- Automatically and "intelligently" locates and modulates up to twenty frequencies per channel in response to the onset of feedback
- Fast feedback detection (less than 0.2 seconds)
- Ultra narrow notch filters for effective feedback suppression while maintaining the sonic integrity of the source material
- “Set and forget" default setting plus Panic button enable fast and easy performance
- Auto mode continually monitors the program material, resetting filters as necessary
- Single shot mode automatically detects and destroys feedback and locks the filter until reset manually
- Manual mode allows setting up of forty individual fully parametric filters with frequency, bandwidth and gain adjustment
- Open MIDI architecture for future software updates and flexible communication with other digital equipment
- Internal switching power supply for maximum flexibility, noise free audio, superior transient response plus low power consumption
|
INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typically >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
The Rane ME 15S microGraphic Equalizer is a two-channel, 2/3-octave design with 20 mm sliders in a single rack space unit. It features a Range switch for high slider resolution in the ±6 dB mode, equivalent resolution to 45 mm sliders found on the DEQ 60L. The ±12 dB mode provides a wide range of control over system audio.
The active filter sections feature Raneʼs innovative constant-Q (constant bandwidth) design. Constant-Q means the bandwidth of each individual filter is guaranteed to be narrow enough to prevent unwarranted interaction between filters, yet wide enough to produce exactly the type of correction curve demanded by even the most unusual acoustic surroundings. This differs dramatically from conventional designs of the past, encumbered with the unfortunate characteristic of changing bandwidth when changing boost/cut amounts.
Front panel controls and indicators include an overall rotary Level control for each channel as well as Overload indicators. Passive pushbutton Bypass switches feature LED indicators, avoiding ambiguity by being on when the unit is Bypassed. (A passive Bypass switch requires no power to operate. This allows completion of the audio path should power fail in the ME 15S.)
Inputs and Outputs are electronically balanced designs, capable of unbalanced operation when required. They accept and drive all possible signal levels into normal load impedances. Balanced applications choose between the XLR or 1/4" Tip-Ring-Sleeve connectors. Unbalanced sources also may tie to the ME 15S through mono 1/4" connectors (no ring connection).
Features - Constant-Q Bandwidth Design
- Overall Level Controls and Passive Bypass Switches
- 20 mm Filter Slide Controls with ±6 dB or ±12 dB Slider Range
- Infrasonic, Ultrasonic, & RFI Filters
- Balanced XLR and 1/4" TRS Inputs and Outputs
- Universal internal switching power supply (100-240 VAC)
|
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
|
- Audiophile 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated Limiters with gain reduction meters for each channel protect your sound system from overload and distortion
- Pink noise generator provides test signals to adapt your sound system to any room acoustics
- Mono subwoofer output with dedicated level control and adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies e.g. floor rumble, hiss etc.
- Highly accurate 8-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
|
Reviews
There are no reviews yet.