| Content | The MINIFBQ FBQ800 features Behringer's FBQ Feedback Detection System that instantly reveals critical frequencies and can also be used as an audio analyzer. An additional low cut filter removes unwanted frequencies such as floor rumble. Accurate 6-digit LED input/output meters and level control are provided for precise level indication. Long-term reliability is guaranteed with Behringer's high-quality illuminated faders, potentiometer and illuminated switches. The ultralow noise audio operational amplifiers offer outstanding sound performance. In addition, all Mini Series models can be stacked on top of each other to create an ultra-compact signal processing solution.
How Does it Work?
Imagine the frequency range of the sound you hear as a highway, a very wide one with nine lanes. Each of these "lanes” represents a single octave of the sonic spectrum. The first four lanes, labeled 63 - 500 (Hz) contain the really low frequency sound content, mainly bass, bass vocals, and the kick and tom drums. The three lanes labeled 1k, 2k and 4k (Hz), make up the fundamental zone of most musical instruments and the male and female vocals. 8k and 16k cover the frequency range of cymbals, snare drums and higher pitched percussion instruments. The FBQ800 allows you to control the flow of audio traffic in each of these nine lanes. When properly applied, EQ makes it possible to hear all of these frequency ranges equally, thus the term equalization.
Feedback Elimination
When a specific frequency, or range of frequencies, reaches too high a level, feedback occurs—that all-too-familiar squeal or howl you get when the mic is too close to the speaker. Basically, feedback happens when there is so much of a particular frequency that it is picked up by the mic and run through the system again. Thatʼs why feedback typically gets louder and louder the longer itʼs allowed to occur. Needless to say, this kind of feedback is very undesirable.
This is where the FBQ800ʼs Feedback Detection System really works its magic. In this ingenious circuitry, LEDs on the individual faders light up when that frequency band is approaching the danger zone. All you need do is lower the illuminated slider until the LED blinks out—voilà, feedback problem solved! What once required a highly trained ear is now an activity that even a child can master.
Sonic Toolkit…
That really is the best way to describe the FBQ800. With its nine frequency bands, you easily fine-tune your sound and instantly eliminate feedback. And each fader can be used to boost or cut the frequency range it controls by as much as 12 dB (and thatʼs a lot!).
Special attention is paid to the low frequency zone. In addition to low frequency faders, the FBQ800 features a Low Cut filter for removing unwanted low frequencies such as floor rumble, room resonance, electrical hum, etc. This is especially handy if your system is being used for speech rather than music.
To Boost or to Cut, That is the Question
Raising and lowering specific frequency bands can improve the frequency response of any roomʼs acoustics. For instance, if the room youʼre in is "bass-heavy,” lowering the 63 and 125Hz faders can help eliminate an overall "boomy” or "muddy” sound. Likewise, gently boosting the 8 and 16k sliders can add sparkle to a somewhat "dark” mix. Are the vocals getting lost in the mix? Raising the level of the 1k slider can help bring them out.
Itʼs important to note that raising a single fader level is not always the best solution; itʼs often better to lower the bands surrounding the frequency you want to bring out, and then boost the overall volume level to achieve better headroom.
Built for Accuracy and Reliability
Speaking of headroom, FBQ800ʼs 6-digit LED I/O meters and level control are provided for precise level maintenance. Long-term reliability is ensured, thanks to high-quality illuminated faders and switches, and our ultra low-noise audio operational amplifiers provide outstanding sonic performance. In addition, all Mini Series components can be stacked to create an ultra-compact signal processing solution.
Mini Series mixer with built-in feedback detection.
FEATURES
- Ultra-compact 9.5" graphic equalizer for studio and stage applications
- FBQ Feedback Detection system instantly reveals critical frequencies
- Additional Low-cut filter removes unwanted frequencies, like floor rumble
- 6-segment LED input/output meters and Level control for precise level indication
- High-quality illuminated faders, potentiometers and illuminated switches
- Low noise audio operational amplifiers offer excellent sound performance
SPECIFICATIONS
MINIFBQ FBQ800 9-Band Graphic Equalizer with FBQ
- INPUT
- Type 1/4" TRS connectors (balanced) or
- RCA connectors (unbalanced)
- Impedance approx. 20k ohms, balanced
- approx. 10k ohms, unbalanced
- CMRR 40 dB typ. @ 1 kHz
- Max. input level +15 dBu
- OUTPUT
- Type 1/4" TS connectors (unbalanced) or
- RCA connectors (unbalanced)
- Impedance approx. 120 ohms
- Max. output level +15 dBu
- SYSTEM SPECIFICATIONS
- Frequency response 10 Hz to 200 kHz, -3 dB
- Dynamic range 110 dB, 10 Hz to 22 kHz
- Distortion 0.003 % typ. @ 0 dBu
- Crosstalk
- Signal-to-noise ratio 10 Hz - 22 kHz
- GRAPHIC EQUALIZER
- Type 9 analog stereo bands
- Control range ±6 dB or ±12 dB, switchable
- Bandwidth 1 oct.
- OTHER FEATURES
- Low-cut filter 75 Hz (12 dB/oct.)
- Input level control -12 dB to +12 dB
- POWER SUPPLY
- Mains connection external power supply
- 9 V ~ / 750 mA
- Mains voltage
- DIMENSIONS/WEIGHT
- Dimensions (H x W x D) approx. 1 8/9" (48 mm) x 9 5/9" (243 mm) x 4 5/7" (120 mm)
- Weight approx. 0.86 lbs. ( 0.39 kg)
|
iEQ-15 Dual 15-Band Graphic EQ with Type V? NR and AFS?
With an EQ heritage that has produced countless industry standard
patents and dates back more than 30 years, the dbx iEQ-31 easily
lives up to the dbx legacy of uncompromised sonic integrity. In
addition to unsurpassed equalization specs, the iEQ-15 also offers
the built-in necessities which include AFS? feedback Suppression,
Type V? noise reduction and PeakStopPlus? limiting. Besides
including two 15-band channels of 2/3-octave equalization, the iEQ-15
also offers +12 dB input gain range; switchable +6 or +15 dB boost/cut
range, 40mm faders, XLR, 1/4'' and Euroblock inputs and outputs,
nonconductive nylon sliders; and an intuitive user interface with comprehensive
output and gain reduction metering. As always, the inevitable result of our
meticulous attention to detail and top-quality componentry is exceptional
sound, performance, and reliability.
The iEQ series represents a major step forward in the performance of EQs.
The iEQ series is now able to offer state-of-the-art digital EQ performance
and specs with an analog look and feel. From its amazing 10Hz to 22kHz
frequency response, to its 113dB dynamic range and Advanced Feedback
Suppression (AFS?), dbx proprietary Type V? noise reduction
and PeakStopPlus? limiting, the iEQ-15 offers out of this world specifications
with a downto- earth price point. Sure to find a home in the studio, on tour and
with installed sound venues, the iEQ-15 is destined to take its rightful place in
the lineage of great dbx? signal processors that are the professional?s choice
in signal processing. With such pristine design and quality, the iEQ-15 offers
the maximum sonic flexibility in a straight forward interface and rock-solid construction.
? Advanced Feedback Suppression (AFS?)
? Type V? Noise Reduction
? PeakStopPlus? Limiting
? 2/3-octave Constant Q frequency bands
? Switchable boost/cut ranges of ±6 or ±15dB
? 18 dB per octave 40Hz low-cut filter
? ±12dB input gain range
? XLR, TRS and Euroblock Inputs and Outputs
? Internal Toroidal Transformer
? Frequency Response of 10Hz to 22kHz
? Dynamic range of greater than 113dB
? User Power Up Features
? Relay Bypass for Power Failure System Protection
|
* 2 channel 15 2/3 octave band graphic equalizer
* 25Hz - 16kHz frequency control * Constant Q circuitry
(3% frequency accuracy) * Selectable 6dB or 12dB control
* Variable level control * By-pass switch * Overload threshold LED (5dB below clipping) * Ground lift switch * XLR & 1/4" TRS balanced Inputs/Outputs * Power: Selectable 120V/220V voltage
* Dimensions: 1.75" H x 19" W x x 8.5" D / 44.5mm x 483mm x 216mm - 1 space r.m. * Weight: 4.5 lbs. / 2.5kg
XEQ-152 Specifactions:
* Input type: Active balanced / Unbalanced * Output Impedance: |
- Audiophile 31-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated Limiters with gain reduction meters for each channel protect your sound system from overload and distortion
- Pink noise generator provides test signals to adapt your sound system to any room acoustics
- Mono subwoofer output with dedicated level control and adjustable crossover frequency
- Additional sweepable high and low-cut filters for each channel remove unwanted frequencies e.g. floor rumble, hiss etc.
- Highly accurate 8-segment LED input/output metering and input gain controls for easy level setting
- Relay-controlled hard bypass with an auto-bypass function during power failure (fail-safe relay)
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
|
DBX 2215 Dual 15-Band Graphic Equalizer with Noise Reduction
It's amazing. One little button. So much effect. dbx? Type III? Noise Reduction is an entirely new concept... virtually instantaneous encode/decode within the circuitry of the box. We started out to build the finest EQs possible, boxes with the heritage and performance to rival our famous 30 Series EQs. And to no one's surprise they came out awfully darn good. (Ask to see the Audio Precision plots compared to the competition.) But then, Roger (our chief engineer, a nice guy, as far as engineers go) got the crazy idea of putting this new noise reduction stuff in the box. We listened to it and were amazed. The EQs sounded great without it but with it the performance was nothing short of incredible. Check it out yourself and see.
But hey, Roger wasn't about to stop there. PeakPlus? Limiter. Who knows more about limiting than the folks at dbx; nobody... that's who. So when the guys were developing this new series of EQs they wanted something that would be unique to these EQs. That's when Roger got another one of his bright ideas and said "I bet they'll work a lot better if there's a cool limiter built in." Next thing you know, all the guys are in the studio amazed at the new limiter Roger had designed specially for the 20 Series. Once again, hearing is believing... With a threshold range of 0dbu to plus 20dbu, the patent-pending PeakPlus limiter is designed to tame your program material from the subtlest nuances to the rowdiest hits. Also, the four stage LED ladder gives you a great visual indication as to what the limiter is doing.
20 Series EQs. You used to have to settle for second best in a reasonably priced EQ but not any more. With the new 20 Series from dbx Professional Products you get a great EQ circuit, a graceful yet powerful limiter and the revolutionary new design of the Type III Noise Reduction. Check out the dbx 20 Series graphic EQs at your pro audio outfitter. You'll see, with the 20 Series EQs you get MORE!!!
SPECIFICATIONS:
|
INPUT
| |
Connectors:
|
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Electronically balanced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 40k ohm, unbalanced 20k ohm
| |
Max Input Level:
|
>+21dBu balanced or unbalanced
| |
CMRR:
|
>40dB, typically >55dB at 1kHz
| |
OUTPUTS
| |
Connectors:
|
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
| |
Type:
|
Impedance-balanaced/unbalanced, RF filtered
| |
Impedance:
|
Balanced 200 ohm, unbalanced 100 ohm
| |
Max Output Level:
|
>+21dBu balanced/unbalanced into 2k or greater
>+18dBm balanced/unbalanced (into 600)
| |
SYSTEM PERFORMANCE
| |
Bandwidth:
|
20Hz to 20kHz, +/-0.5dB
| |
Frequency Response:
|
50kHz, +0.5/-3dB
| |
Noise Reduction In:
|
(+/-6 and +/-15dB range):
| |
Signal-to-Noise:
|
>102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>120dB, unweighted
| |
Noise Reduction Out:
|
(+/-6dB range):
| |
Signal-to-Noise:
|
>94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
| |
Dynamic Range:
|
>112dB, unweighted
| |
Noise Reduction Out:
|
(+/-15dB range):
| |
Signal-to-Noise:
|
>90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
| |
Dynamic Range:
|
>108dB, unweighted
| |
THD + Noise:
|
| |
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
|
Reviews
There are no reviews yet.