Content |
The VX-200XI module is designed to be used in conjunction with the VX-2000 System Manager, and comes with control input terminals, low-cut and high-cut filters, and gain controls.
* 0 dB = 1 V Power Source | Supplied from VX-2000 | Current Consumption | Under 30 mA | Input Sensitivity (Rated Output -20 dB) | MIC: -70 to -42.5 dB* (adjustable)
LINE: -20 to +7.5 dB* (adjustable)
MIC or LINE selectable by the built-in switch | Low Cut Filter (100 Hz) | 9 to 15 dB attenuation (adjustable) | High Cut Filter (10 kHz) | 8 to 14 dB attenuation (adjustable) | Distortion | Under 0.5% | Frequency Response | 50 - 20,000 Hz | Phantom Power | 15 V (open), 6 V (current consumption: 3.3 mA) | Control Input | No-voltage make contact, open voltage: 17 V DC,
short-circuit current: Under 5 mA | Input Connector | RJ45 female connector
Twisted-pair straight cable (TIA/EIA-568A standard) | Finish | Panel: Aluminum, hairline | Dimensions | 35 (W) × 78 (H) × 88 (D) mm | Weight | 70 g | Accessory | Mounting screw……2 | Option | Isolation transformer: IT-450 | Applicable Model | VX-2000 |
|
The AT series high quality attenuators features 5 attenuation settings ,,OFF'' -18dB,-12db,-6dB,-0dB. An input range from 0.5W to 60W (model dependent), and push-in connectors. Push-in connector allows quick terminal cable connection. Stylishly finished, the AT Series will suit any décor. | RM-200M - Five/ten zone console for VM-2120/2240 amplfiers
The RM-200M Remote Microphone that allows announcements to be made to any speaker zone and emergency announcements to all zones on a system with the VM-2120/2240 system management amplifiers.
These announcements can be made live or pre-recorded announcements
can be activated. The remote microphone is connected by cable to the
RM-210 Remote Microphone Extension unit.
SPECIFICATIONS:
Power Requirement |
24 V DC (12-30 V DC), (Supplied from VM-2120/VM-2240 Amplifier or local power suppy.) |
Distortion |
Less than 1% |
Frequency Response |
100 - 10,000 Hz |
Distortion |
Less than 1% |
Signal-to-Noise Ratio |
More than 60 dB |
Audio Output |
0 dB*1, 600 O, balanced |
Microphone |
Unidirectional electret condenser microphone, gooseneck type. |
Speaker Zone Control |
Zones 1-5 (Zones 1-10 with 2 stacked amplifiers) Groups 1-2, and All-Zone Broadcast |
Emergency Broadcast |
Activation of Emergency Broadcast (pre-recorded announcement*2 or live microphone announcement) by Emergency Switch |
Voice Announcement Board Control |
Activation of 5 messages*2 |
Number of Connectable Units |
Up to 4 |
Communication System |
RS-485 |
Volume Control |
Microphone volume control |
Connection Cable and Connector Category |
5 STP cable, RJ45 connector |
Communication Distance |
800 m maximum in total |
Finish |
ABS resin |
Dimensions |
190 (W) × 75.7 (H) × 21.5 (D) mm (Gooseneck microphone excluded) |
|
*1 0 dB = 1 V
*2 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier. |
|
*Convenient Priority Broadcasting
*Convenient Installation and Construction without ID Setting
*RS-422 Communication between RM-500 and Z-500
*21 Zone Paging Selection
*Output Signal Level Display
*Multi Chime Options
*Weight: 1.6kg/3.5Ib
*DImensions(W×H×D): 200×206×70mm/7.9×8.1×2.8in
|
The AT series high quality attenuators features 5 attenuation settings ,,OFF'' -18dB,-12db,-6dB,-0dB. An input range from 0.5W to 60W (model dependent), and push-in connectors. Push-in connector allows quick terminal cable connection. Stylishly finished, the AT Series will suit any décor. |
| - SYSTEM POWER CONTROL You can control the power of your system by using this model. - AC AND DC POWER SUPPLY You can distribute AC and DC power through the AC outlet and DC terminals on the rear panel. - USE OF EMERGENCY POWER SUPPLY For emergency equipment power supply, an extra DC terminal is provided. - REMOTE CONTROL You can control the system power by remote control function even though the power switch on front is off. - AC AND DC VOLT METER This model uses digital volt meter displays of AC and DC. - OPERATING MODE DISPLAY You can easily check the operating mode by LEDs, AC or DC operating and emergency power. | | | | | PD-659 | AC Outlet | Switched 2000W ⅹ3 | Unswitched 700W ⅹ1 | Remote Control | 1 | DC Power Output | DC 24V 5A | Operation Temperature | -10℃~+40℃ | Power Source | 100-120VAC or 220-240VAC; 50/60Hz (Supplied ACmains transformer depends on country requirements) | Power Consumption | 190W | Weight(SET) | 6.2Kg/13.6Ib | Dimension(SET) | 482(W) x 88(H) x 380(D)mm/19(W) x 3.5(H) x 15(D)in | ※ Specifications and design subject to change without notice. | | | |
|
Reviews
There are no reviews yet.