| Content |
INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typically >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: | INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typicall >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
Phonic's GEQ3102F is the authentic soundman's choice of EQ - a dual channel 31-band equalizer, offering 6 or 12 dB of cut or boost on standard ISO center frequencies between 20 Hz and 20 KHz. The GEQ3102F is 2-rack space units high and accepts both 1/4" TRS phone jacks and XLR connectors, making it ideal for any studio or live venue setup.
- Sweepable high and low cut filters on each channel to remove unwanted frequencies
- Ultra low-noise audio operational amplifiers offer outstanding sound performance
- Relay-controlled hard-bypass with an auto-bypass function during power failure
- Dedicated subwoofer output with user-adjustable low-pass filter
- Feedback detection circuitry for indicating critical frequencies
- Balanced inputs and outputs with 1/4" TRS and XLR connectors
| PRICE WITHOUT V.A.T.
BSS Opal FCS-966 Constant Q Graphic Eq
Graphic equalisers are found in just about every sound application, from room contouring to feedback control and general audio sweetening.
Traditionally, much general eq'ing takes place on the faders alone, but this restricts the use of the faders at each end of the scale for further precision eq work. So we provided the Opal FCS-966 with separate LF and HF contour filters which can change an overall sound balance without disturbing a detailed room or loudspeaker response.
These filters are very musical gentle boost and cut shelving filters which can be used to add (or remove) room effects that change with temperature, audience numbers or humidity.
All these effects can be easily made without disturbing the critical fader settings already made.
Constant Q Filters
The modern generation of graphic eq's
uses the Constant Q topology, pioneered by BSS Audio, which means that the filter width is constant whatever the fader gain setting.
Compared to the earlier 'gyrator' style of filters, Constant Q filters provide a smoother and more predictable interaction between adjacent faders and the resulting eq curve more closely resembles the actual fader positions.
More Gain Control Per Filter
Each eq fader has +/-15dB of adjustable gain, more than many competitive graphic eq's. The faders are long-throw 45mm types for precision control.
High Pass Filter
Also provided on the FCS-966 is a sweepable high-pass filter which can be used very effectively to restrict the low-energy output for better amplifier and loudspeaker performance. Stage monitors also benefit from the application of a high-pass filter to remove bass signals e.g. from vocal-only wedges.
Metering
BSS Audio believes in providing engineers with information, and the FCS-966's 8-segment led meter shows output level and warns of signal clipping within the eq. When the unit is switched to bypass, the meter will read the input level, allowing accurate matching of the 'dry' and equalised signals using the gain control.
Centre Bypass
When any eq fader is in its centre detent position, the filter is automatically bypassed, for optimum performance.
Input/Outputs
All the inputs and outputs of the FCS-966 are electronically balanced, with optional transformer balancing. To make installation of the FCS-966 easier, we've provided three differerent interface connectors: XLR-type, 1/4" TRS jack and Phoenix/Combicon screw terminals.
Relay Bypass
The EQ IN buttons switch the EQ path
into circuit. When switched out, or power fails, a high-quality relay switches the input signal directly to the output connectors.
Control Descriptions
Faders
30 EQ filter faders on ISO centres, each with nominal +/-15dB of gain. Positive centre-detent on 45mm long-throw precision faders.
HP Filter
Sweepable high pass filter, frequency adjustable from OUT (flat) up to 250Hz.
LF Contour
Smooth shelving filter, +/-6dB of gain at 50Hz
HF Contour
Smooth shelving filter, +/-6dB of gain at 14kHz.
GAIN
Used for overall unity gain adjustment. Adjustable from - infinity to +10dB.
CLIP
Triple-point clip detector that indicates red when the internal signal is clipping at any one of three critical points.
LED Meter
Shows output signal level (input signal when eq is bypassed) from -24dBu to +18dBu in 8 steps. |
In today's recording and sound reinforcement environments, the need for multiple channels of high quality, easy to use compression is growing rapidly. The new dbx® 1046 is designed to provide the audio professional with just that: 4 channels of great sounding dbx compression for a variety of applications. Incorporating the industry standard dbx designs and the latest available manufacturing techniques, the dbx 1046 provides pristine sonic quality with that classic dbx sound.
The 1046 provides 4 channels of smooth classic dbx OverEasy® or Hard Knee compression that are perfectly suited for use on individual tracks of your multitrack recorder, and in virtually all applications the separate channels can be individually interfaced and used for entirely independent purposes. Additionally the newly developed PeakStopPlus™ is ideal for protecting your system from the oppressive peaks that can take out valuable drivers in your sound reinforcement rig or studio monitors.
All four channels have the following controls:
Threshold - allows you to set the level at which the compressor starts affecting the gain
OverEasy - allows you to select between soft compression for overall gain control or Hard Knee compression based on the characteristics of the original dbx 160.
Ratio - allows you to set the slope of gain reduction affecting the signal over the threshold level.
Input/Output Meter - allows you to set the meter to check the input and output levels for maximum signal-to-noise ratio and best level matching.
Output Gain - allows you to add make-up gain or to adjust the output level for that channel to match the next device's input gain.
Bypass - hard wire bypass allows you to hear how the compressor is affecting your signal.
PeakStopPlus - allows you to set the maximum signal level you want to pass through this channel. While it's virtually impossible to eliminate distortion, the PeakStopPlus circuit does it gracefully and effectively with minimal distortion.
Stereo Link - allows you to link channels 1&2 and 3&4 for two channels of true stereo compression.
All four channels feature balanced gold plated XLR and 1/4" inputs and outputs, and switchable +4dBu or -10dBV operating level to interface each individual channel with any other device.
So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx 1046 is for you.
- Four independent channels of operation, stereo linkable in two pairs
- PeakStopPlus™ limiting control for setting maximum allowable level regardless of compressor settings
- Independent Threshold and ratio controls
- Switchable OverEasy® or Hard Knee compression
- Classic dbx® compression
- Differentially balanced gold-plated XLR and 1/4" inputs and outputs
- True RMS level detection
- Precision metering of input level, output level, and gain reduction
- Dual True stereo or quad mono operation
- Switchable +4dBu or -10dBV operation per channel
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Input Type | Electronically balanced/unbalanced, RF filtered | | Input Impedance | Balanced > 40 kOhm, unbalanced >20 kOhm | | Max Input | > +22 dBu balanced or unbalanced | | CMRR | Typically >50 dB at 1 kHz | | Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) | | Output Type | Servo-balanced/unbalanced, RF filtered | | Output Impedance | Balanced 30 Ohm, unbalanced 15 Ohm | | Max Output | > +22 dBm balanced, > +20 dBm unbalanced | | Bandwidth | 20 Hz to 20 kHz, +0/-0.5 dB | | Frequency Response | 0.35 Hz to 90kHz, +0/-3 dB | | Noise | | | Dynamic Range | > 118 dB, unweighted | | THD+Noise | >0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), | | IMD | | | Interchannel Crosstalk | | | Stereo Coupling | True RMS Power Summing | | Compressor Threshold Range | -40 dBu to +20 dBu | | Compressor Ratio | 1:1 to infinity:1 | | Compressor Threshold Characteristic | Selectable OverEasy® or hard knee | | Compressor Attack/Release Characteristic | AutoDynamic™ | | Compressor Attack Time | Program-dependent | | Compressor Release Time | Program-dependent | | Compressor Output Gain | -20 to +20 dB | | Limiter Threshold Range | 0 dBu to +24 dBu (off) | | Limiter Ratio | infinity:1 | | Limiter Type | PeakStopPlus® two-stage limiter | | Limiter Stage 1 | PeakStop® brickwall limiter | | Limiter Stage 1 Attack Time | Zero | | Limiter Stage 1 Release Time | Zero | | Limiter Stage 2 | Predictive intelligent program limiter | | Limiter Stage 2 Attack Time | Program-dependent | | Limiter Stage 2 Release Time | Program-dependent | | OverEasy® Switch | Activates the OverEasy compression function | | I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter | | Bypass Switch | Activates the direct input-to-output hard-wire bypass | | Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneously for both input and output levels | | ST Link Switch | Links channels in stereo pairs. Channels One and Three become the master channels | | Gain Reduction Meter | 8 segment LED bar graph at 1, 3, 6, 10, 15, 20, 25, and 30 dB | | I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu | | PeakStop™ Indicator | 1 LED to indicate PeakStop™ limiting | | Function Switches | LED indicator for each front-panel switch | | Output Transformer Options | Jensen® JT-123-dbx or JT- 11-dbx, BCI RE- 123-dbx or RE-11-dbx | | Operating Voltage | Switchable:100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz | | Power Consumption | 20 Watts | | Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T | | Power Connector | IEC receptacle | | Dimensions | 1.75“Hx19“Wx9“D (4.4cmx48.3cmx20.1cm) | | Unit Weight | 5.2 lbs. (2.4 kg) | | Shipping Weight | 7.6 lbs. (3.5 kg) |
|
The Rane ME 15S microGraphic Equalizer is a two-channel, 2/3-octave design with 20 mm sliders in a single rack space unit. It features a Range switch for high slider resolution in the ±6 dB mode, equivalent resolution to 45 mm sliders found on the DEQ 60L. The ±12 dB mode provides a wide range of control over system audio.
The active filter sections feature Raneʼs innovative constant-Q (constant bandwidth) design. Constant-Q means the bandwidth of each individual filter is guaranteed to be narrow enough to prevent unwarranted interaction between filters, yet wide enough to produce exactly the type of correction curve demanded by even the most unusual acoustic surroundings. This differs dramatically from conventional designs of the past, encumbered with the unfortunate characteristic of changing bandwidth when changing boost/cut amounts.
Front panel controls and indicators include an overall rotary Level control for each channel as well as Overload indicators. Passive pushbutton Bypass switches feature LED indicators, avoiding ambiguity by being on when the unit is Bypassed. (A passive Bypass switch requires no power to operate. This allows completion of the audio path should power fail in the ME 15S.)
Inputs and Outputs are electronically balanced designs, capable of unbalanced operation when required. They accept and drive all possible signal levels into normal load impedances. Balanced applications choose between the XLR or 1/4" Tip-Ring-Sleeve connectors. Unbalanced sources also may tie to the ME 15S through mono 1/4" connectors (no ring connection).
Features - Constant-Q Bandwidth Design
- Overall Level Controls and Passive Bypass Switches
- 20 mm Filter Slide Controls with ±6 dB or ±12 dB Slider Range
- Infrasonic, Ultrasonic, & RFI Filters
- Balanced XLR and 1/4" TRS Inputs and Outputs
- Universal internal switching power supply (100-240 VAC)
|
Reviews
There are no reviews yet.