Content |
- Signal to Noise (20 Hz - 20 kHz): 100 dB - Input Sensitivity: 1.2 Vrms - Voltage Gain (8 Ohms): 34.4 dB - Output Circuitry: 2-tier Class H - Power Requirements: 6A - Frequency Response: 20 Hz - 20 kHz, +0, 1 dB - Dynamic Headroom (4 Ohms): 2 dB - Damping Factor: 100 - Input Impedance: Greater than 20k (balanced) - Maximum Input Level: +24 dB (16 Vrms) - Input Connectors (each channel): 3-pin XLR and 1/4-inch TRS, balanced, parallel Phono, unbalanced - Output Connectors (each channel): Speakon, 1/4-inch, Binding Posts - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection Load protected against DC faults - Rear Panel Controls: Full Range / Crossover switch - Dimensions (H x W x D): 3.5 x 19 x 10.1 inches (89 mm x 483 mm x 257 mm) - Weight: 26 lbs (12 kg) Front Panel Controls and Indicators: - Gain controls, 21 detents - Red Clip LEDs, proportional, 0.1% THD threshold - Green Signal LEDs, threshold -35 dB - Blue Power LED, AC on Stereo Mode: - 8 Ohms / both channels driven: 500 Watts - 8 Ohms / single channel driven: 600 Watts - 4 Ohms / both channels driven: 700 Watts - 4 Ohms / single channel driven: 850 Watts Distortion: - 8 Ohms: less than 0.05% - 4 Ohms: less than 0.1% Dimensions and Weight in Packaging Shipping Weight: 31 lbs Shipping Dimensions: 24 x 15 x 7 in
|
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 8 to 10 kg (18 to 22 lbs) Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)
|
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements in reliability, flexibility and sound. Alone or in combination with the other products of the Bittner portfolio. The consequent realisation of the Bittner quality standards indicates once more our understanding of the contracting business. It underlines our philosophy that cost consciousness has nothing to do with giving up standards. Compromise is a word unknown to Bittner Audio! The incorporation of detent potentiometers, clip limiter, protection circuits for any imaginable situation, as well as a first-class production process using only highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay XLR Inputs Speakon and Binding Posts Clip Limiter Toroidal transformers LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed, low noise fans Detent potentiometers Stereo / Bridged / Parallel Mode Ground Lift Robust Steel Chassis 3 Year Warranty
TECHNICAL DATA: Basic 1200: 2x 600 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.03% Signal-to-Noise Ratio: < -102 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: > 400 @ 4 Ohm Cooling: 2x Fan (temp. reg. variable speed) Weight: 15 kg. Dimensions : 2 RU / 483 x 88 x 454 mm (19" x 3.5" x 17.9“) |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 500W
4Ω EIA 1 kHz 1% THD - 850W
2Ω EIA 1 kHz 1% THD - 1250W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 1700W
4Ω EIA 1 kHz 1% THD - 2500W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 3.28V
32dB Setting - 1.60V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 34.5dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -106dB
Total Harmonic Distortion (THD) 0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 8.5A
230V 50Hz - 7.5A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Number of Channels: 2
Output Power: (per channel)
8 ohms 450W
4 ohms 850W
2 ohms 1550W
Output Power: (bridged)
8 ohms 1700W
4 ohms 3100W
THD%: (@1dB below max output)
@ 1kHz | Crown XTi2002 Specifications:
* Output Power 2 ohms Stereo (per ch): 1000W
* Output Power 4 ohms Stereo (per ch): 800W
* Output Power 8 ohms Stereo (per ch): 475W
* Output Power 8 ohms Bridged-Mono: 1600W
* Output Power 4 ohms Bridged-Mono: 2000W
* Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
* Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
* Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
* Total Harmonic Distortion (THD):
* Damping Factor 20 Hz to 1 kHz: > 500
* Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
* Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
* Maximum Input Signal: +22 dBu typical
* Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
* Level Control: Two front-panel rotary level controls, one for each channel
* Power Switch Control: On/Off switch applies AC power to the amplifier
* Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
* LCD Screen: Backlit liquid crystal display that shows preset and processing status
* Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
* –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
* –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
* Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
* Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
* Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
* Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
* Input Connectors: XLR, one per channel
* Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
* Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
* HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
* Chassis: Steel
* Front Panel: Cast-aluminum
* Cooling: Proportional speed fan with front-to-rear airflow.
* Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
* Net Weight: 18.5 lbs (8.4kg)
* Shipping Weight: 21.5 lbs (9.8kg) |
Reviews
There are no reviews yet.