QSC CMX-300V POWER AMPLIFIER 2x300W RMS @ 4Ω, 2x430W RMS @2Ω, bridged (mono) 830W RMS @ 4Ω.

Stereo Mode Ratings (Both Channels Driven):

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 185W
    - EIA 1 kHz, 0.1% THD: 200W
    4 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 280W
    - EIA 1 kHz, 0.5% THD: 300W (1% THD)
    2 ohms:
    - EIA 1 kHz, 1% THD: 430W

Bridged Mono Mode Ratings/Specifications:

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 530W
    - EIA 1 kHz, 0.1% THD: 600W
    4 ohms:
    - EIA 1 kHz, 1% THD: 830W
    70V Direct Drive:
    - EIA 1 kHz, 1% THD: 600W
    Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
    Input Sensitivity @ 8 Ohms: 1.15V (+3.4 dBu)
    Voltage Gain @ 8 Ohms: 31.6x (30 dB)
    Output Circuitry: Class AB
    Power Requirements (120V):
    - 1/8 power pink noise at 4 ohms: 4.4A
    - 1/3 power pink noise at 4 ohms: 6.6A
    Power Requirements (230V):
    - 1/8 power pink noise at 4 ohms: 2.2A
    - 1/3 power pink noise at 4 ohms: 3.3A
    Distortion (SMPTE-IM):

• Rack mount stereo powered monitor speaker system
• New AES/EBU digital input
• lndependent MUTE function
• Sophisticated control panel section
• Ideal where space is at a premium

• Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
• AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
• Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
• Independent MUTE function by holding down CH SEL key for a while.
• Auto Mute when powering on*.
• D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
• Multi-voltage power supply.

Speaker Section

• Unit: 110 x 40mm cone type, magnetically shielded, x 2
• Impedance: 8 ohms
• Output SPL: 84 dB/W (1m)
• Frequency response: 200Hz to 20kHz

Amplifier Section

• Rated output power: 10W or more (8 ohms, 1kHz)
• Residual noise: -60 dBV or less (DIN AUDIO)
• Distortion: 0.5% or less (10W / 4 ohms, 1kHz)

Digital input

• Connector: XLR-3-31 type
• Digital input Format: IEC60958 (AES/EBU)
• Digital inputSampling frequency: 44.1kHz to 96 kHz
  

Analog input

• Connector: XLR / 1/4" combi-jack
• Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
• Analog input Input impedance 10k ohms or more

Phones

• Connector: 1/4" stereo jack
• Applicable load imp. 8 ohms or more
• Rated output power 20mW + 20mW (32 ohms, 1kHz)

General

• External dimensions: 430(W) x 44(H) x 282(D) mm
• Weight: Approx. 3.5kg
• Power requirement: 100 - 240V~, 50/60Hz
• Power consumption: 10W

Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)

• 2Χ350W 8Ω 2x500W 4Ω 2x650W  STEREO MODE
  
  
  
• BRIDGE 2000W 4 Ω
• 16Kg

• 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
• Precise Power, Signal and Clip LEDs to monitor performance
• XLR and 1/4" TRS input connectors for compatibility with any source
• Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
• Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
• Independent limiters per channel offer reliable protection against overload and distortion
• High-current toroidal transformer for ultra-high transient response and absolute reliability
• Ultra-reliable Toshiba/Fairchild power transistors
• Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
• “Back-to-front” ventilation system including air filter for reliable operation
• “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
• High-quality components and exceptionally rugged construction ensure long life
• Conceived and designed by BEHRINGER Germany

A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 250 Watt / 8Ω RMS, 2 x 450 Watt / 4Ω RMS, 900 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.

• Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
• High-current toroidal transformers for greater power and low noise
• Independent user-defeatable peak limiters reduce distortion
• Selectable High-Pass filter at 30Hz or 50Hz
• XLR and 1/4' TRS input jacks
• Binding post and Speakon?-type outputs
• Front mounted gain controls for easy access
• Signal and Peak LED indicators to monitor performance
• Short circuit, thermal, subsonic, RF protection, output DC offset
• Power on/off muting