Content | Suggested for Speech, Head-worn microphone, Sports/Aerobics
- Ergonomically optimized behind-the-neck headband
- Moisture shield
- External shock mount for high mechanical-noise rejection
The C 544 L is a head-worn miniature condenser microphone with a convenient behind-the-neck headband. The microphone has a cardioid polar pattern and therefore "prefers” sounds arriving from the front (from the userʼs mouth).
The microphone body containing the condenser transducer is shock mounted on the microphone arm in order to suppress cable and mechanical noise. The microphone arm will place the microphone in front of the corner of your mouth to minimize pop noise and protect the microphone from contamination. The supplied windscreen makes the microphone even less susceptible to wind and pop noise.
A special moisture shield on the microphone capsule makes it difficult for moisture and makeup to penetrate into the microphone. This barrier prevents the microphone sound entries from being clogged by sweat or makeup which would make the sound dull and reduce the sensitivity of the microphone. Therefore, never remove the moisture shield from the microphone.
The C 544 L is a condenser microphone and therefore needs a power supply.
Type |
Pre-polarized condenser microphone |
Polar pattern |
cardioid |
Frequency range |
20 Hz to 20,000 Hz |
Sensitivity |
40 mV/Pa (-28 dBV re 1 V/Pa) |
Max. SPL |
126 dB / 130 dB (for 1%/3% THD) |
Equivalent noise level (IEC 60268-4) |
22 dB-A |
Impedance |
200 ohms, electronically balanced |
Recommended load impedance |
>2000 ohms |
Supply voltage |
9 V battery supply through B 29 L or bodypack transmitter, or 9 to 52 V universal phantom power through MPA V L adapter |
Powering |
approx. 2 mA |
Environment |
temperature: -20°C to +60°C, R.H. at +20°C: 99% |
Cable |
1.5 m (5 ft.) |
Finish |
matte black |
Dimensions |
130 mm (5.2 in.) in dia. |
Net weight |
30 g (1.1 oz.) exc. of connector |
Shipping weight |
200 g / 7.1 oz. |
|
Transducer Condenser Polar Pattern Omnidirectional Frequency Response 30Hz to 20kHz +/- 3dB Dynamic Range (Typical) Not Specified by Manufacturer Signal-to-Noise Ratio Equivalent Acoustic Noise: 29dBA SPL Maximum Input Sound Level 130dB SPL Power Requirements Operating Current: 500uA Operating Voltage: 1 to 2V Power Supply Voltage: +3V with 2.7k ohm Load +5V with 6.8k ohm Load +9V with 15k ohm Load Output Impedance 2k ohms Output Connectors TA4-Female Connector for Shure Wireless Transmitters Dimensions Not Specified by Manufacturer Weight 0.07 oz (2g) | Shure WH20TQG Dynamic Headset Microphone Shure Performance MicrophonesDynamic Headset Microphone
The improved version of the WH10, the Shure Model WH20TQG is a rugged, light-weight, dynamic headset microphone that provides high-quality voice pickup. It fits securely for active microphone users, such as aerobics instructors and musicians, with low visibility for stage appearances. The WH20 is suitable for any voice communications application where comfort and reliability are required.
The WH20 TQG has a cardioid (unidirectional) pickup pattern. This provides greater gain-before-feedback and isolation from ambient noise and other unwanted sound sources, such as air-conditioning, musical instruments and loudspeakers. A carefully shaped frequency response includes a voice-frequency presence peak and a low-frequency rolloff to compensate for the proximity effect inherent in cardioid microphones during close-talk operation.
An integrated elastic CROAKIES ? headband secures the headset comfortably. The headband, wireframe, and gooseneck are adjustable to accommodate any head size or shape. The WH20 TQG is supplied with a foam windscreen and clothing clip.
Features:
- Lightweight wireframe and headband adjust for a secure, comfortable fit
- Extra-strong, small-diameter attached microphone cable resists breakage
- Collapsible microphone boom for easy storage and transportation
- Smooth, natural frequency response comparable to high-quality dynamic hand-held vocal microphones
- High input clipping level eliminates overload distortion
- Reliable at temperature and humidity extremes
- Supplied foam windscreen and clothing clip
- The WH20TQG has a miniature four-pin female Tini "QG" connector for direct connection to Shure wireless body pack transmitters - This microphone to be used ONLY with an existing Shure body-pack transmitter.
Transducer
|
Dynamic, close-talking |
Polar Pattern |
Cardioid |
Frequency Response |
50 Hz to 15 kHz, Measured @ 0.3" (8.0 mm) |
Power Requirements |
Dynamic (Requires NO Phantom Power) |
Impedance |
150 ohms (200 ohms actual) |
Output Level |
Open Circuit Voltage: -67 dB/Pa (1.48' / 0.45 m)
1 Pa = 94 dB SPL
Close-talked (@ 0.50" / 12.5 mm) @ 1,000 Hz |
Electromagnetic Hum Sensitivity |
38.4 dB equivalent SPL in a 1 mOe field |
Operating Temperature |
0 to 140°F (-18 to 60°C) |
Storage Temperature |
-20 to 165°F (-29 to 74°C) |
Connector |
TA4F connector for Shure bodypack transmitters |
Cable Length |
4.0' (1.2 m) |
Dimensions |
Not specified by manufacturer |
Weight |
2.2 oz (63 g) including connector |
Packaging Info |
Package Weight |
0.7 lb |
Box Dimensions (LxWxH) |
7.6 x 6.4 x 3.1" |
|
Transducer Condenser
Polar Pattern Omnidirectional
Frequency Response 30Hz to 20kHz +/- 3dB
Dynamic Range (Typical) Not Specified by Manufacturer
Signal-to-Noise Ratio Equivalent Acoustic Noise: 29dBA SPL
Maximum Input Sound Level 130dB SPL
Power Requirements Operating Current: 500uA
Operating Voltage: 1 to 2V
Power Supply Voltage:
+3V with 2.7k ohm Load
+5V with 6.8k ohm Load
+9V with 15k ohm Load
Output Impedance 2k ohms
Output Connectors TA4-Female Connector for Shure Wireless Transmitters
Dimensions Not Specified by Manufacturer
Weight 0.07 oz (2g)
|
Shure WBH54T Tan Headworn Condenser Microphone
WBH54B is a subminiature, electret condenser head worn microphone. It provides uncompromised
sound quality and reliability with minimal visibility in applications such as broadcast, theater, and touring.
Despite their small size, the condenser element delivers full, clear, and natural reproduction of speech
and vocals. The microphone features a durable, low-profile wire frame headband which is fully adjustable for
stability and comfort. A plastic carrying case protects the microphone and its accessories.
Features:
Supercardioid polar pattern provides maximum gain-before-feedback and ambient rejection
Extended frequency response tailored for vocal performances
Able to handle extremely high sound pressure levels (SPL)
Snap-fit foam windscreens stay in place during intensive movement
Available with an in-line preamp or with a TA4F connector for wireless applications
Black finish
TA4F connector for wireless applications
| Headset Mikrofon for WS 100 Series, WS 1000 Series, WS 1616 Series and WS ECO Series
- Uni-directional Electret Condenser Headset Microphone
- Impedance
- Frequency range : 20Hz - 20 KHz
- Sensitivity : -44 ± 2 dB (at 1 KHz)
Product type
Wireless Microphone System Accessories
Type
Headsets
Frequency response
20 - 20.000 Hz
Directivity
cardioid
Nominal impedance
680 Ohm(s)
Phantom power requierements
5 V
Microphone input
mini-XLR (3-pin, female)
Accessories (included)
Foam windscreen
Weight
0,06 kg |
Reviews
There are no reviews yet.