AKG C 562CM OMNIDIRECTIONAL-HEMISPHERICAL CONDENSER BOUNDARY MIC

C 562 CM 

Small, low-profile boundary layer microphone
Wide frequency range
High sensitivity
Ideal for inconspicuous installation in a room
Suited for surveillance or recording
 
The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL.
The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings,
walls, tables, stage props, etc.
Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording
since a single microphone can cover an entire room. The supplied XLR phantom power adapter
connects to the microphone cable through a miniature connector so installation holes can be
smaller than the diameter of the phantom power adapter.
 
SPECIFICATIONS:
Polar pattern omnidirectional (hemispherical)
Frequency range 20 to 20,000 Hz
Sensitivity 25 mV/Pa (-32 dBV)
Max. SPL 130 dB (k=1 %)
Equivalent noise level 16 dB-A
Signal/noise ratio (A-weighted) 78 dB
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN/IEC
Current consumption Connector 3-pin XLR
Cable 0.5 m (20 in.)
Finish matte nickel plated
Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.)
Net weight 30 g (1.1 oz.)
Shipping weight 195 g (76.9 oz.)
 

Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility
• Available in two colors: black (U891Rx) and white (U891RWx)

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 264 g
• Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
• Output Connector: TB3M-type
• Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors

The e 912 is a pre-polarized condenser boundary microphone with
half-cardioid pick-up pattern. Its acoustic properties have been
optimized for instruments, vocals and speech. The e 912 is an ideal
choice for pianos, theatre and opera productions, conference applications,
altars and lecterns.To optimally match the installation environment,
the e 912 is available in black or creme white.

Features
Frequency response and sensitivity optimized for picking up instruments,
vocals and speech
Unobtrusive, flat housing
Extremely rugged and step-resistant
Shock-absorbing rubber base
Mounting slots for table installation
Gold-plated XLR connector
Integrated pre-amp 
Delivery Includes
e 912 Microphone
Pouch
User manual

Technical Data
Transducer principle (Microphone)  permanently polarized condenser 
Pick-up pattern  half-cardioid 
Sensitivity in free field, no load (1kHz)  10 mV/Pa 
Max. Sound pressure level (aktiv)  135,6 dB 
Equivalent noise level  26 dB(A) 
Phantom powering  48 V / 1,1 mA 
Nominal impedance  Min. terminating impedance  1000 Ohm 
Dimensions  126,5 x 105 x 26,5 mm 
Weight  ca. 550 g 
 

 MX393C - Condenser Boundary Microphone, Built-in Preamp, 12-ft Tini "QG" ? to XLR Cable, Programmable Switch and LED Indicator