| Content | PA amplifier / paging system, 480W, 5 speaker zone attenuator, slot module, 3 x mic/line-in, 3 x line-in, priority switch, built-in chime
This series of amplifiers always has the same output point: your music is distributed to a maximum of 5 zones, which may or not be interrupted to put out a call.
For each zone, the volume can be controlled separately. Connection to an alarm system or telephone switchboard can be made in an instant. In short, the ideal all-in formula.
Features
• Rated outputs : 480 W (RMS) on 25 V, 35 V, 50 V,
70 V & 100 V.
• "Voice priority” on input 1 mutes
inputs 2-aux, Pack Signal, "Chime
+ Mute” contact on input 2-4 has
priority to aux input Pack Signal.
• Detachable screw terminals for input
2-4.
• Mic/Line switch for input 2-4.
• Phantom switch on input 1-4.
• Mic input surge-protection.
• Pre out/Amp in for extensions with
other amplifi ers.
• RCA cinch for input 5-7 (aux selector).
• Slot for input modules JTP-10,
JDM-10A,JCDP-10MP, JCDR-10RDS
• Bass-Treble tone control
(100Hz, 10KHz).
• 5 speaker zone attenuator.
• Connection of paging microphone
(JPS-10).
• Variable speed fan.
• Over current protection.
• Thermal protection.
• Short circuit protection.
• AC operation – DC 24V operation
|
XV Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile,
dynamic and extremely rugged according to IEC286-3. For the
highest requirements in safety and quality.
Sequential power on, alive contacts and incorporated ground fault
detection - the XV is the solution under all conditions. Without the
need for additional equipment. For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers
in the XV series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 1600: 2x 800 W / 100 V
Class: AB
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans(temp. reg. variable speed)
Weight: 39 kg
Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
The new DA Series digital multi-channel amplifiers are the latest addition to the TOA line of industry-standard audio products for installed sound. The DA Series is ideal for multi-zone distributed speaker systems and professional sound applications.
Engineered with Class D technology, the new DA Series amplifiers operate at 85 percent efficiency and consume almost one-third less power than conventional analog amplifiers. The compact and lightweight (14.6 lbs.) single rack-space design and ultra-low heat dissipation allow designers to rack-mount up to five units without open space between units.
The first phase of the DA Series is comprised of two models; the high-impedance DA-250FH provides four 100 Volt output channels of 250 Watts. The low-impedance model DA-250F provides four channels of 250 Watts at four ohms or two channels of 500 Watts at eight ohms in bridged mode. Additional models are scheduled to be launched in 2007.
Equipped with an independent power supply for each channel, the new multi-channel amplifiers offer unmatched reliability and performance. Other features include recessed stepped attenuators for precise gain calibration, removable dust filters for easy maintenance, and optional isolation transformer.
- FEATURES :
- DA-250FH
- 4x 250W (100V)
- 2x 500W bridged mode (100V)
- Limiter and High pass filter
- 4x 250W (4 ohms) / 170W (8 ohms)2x 500W bridged mode (8 ohms)
- Limiter
- Class D design – 85% efficient!
- 30% lower power consumption than conventional amplifiers
- Compact, single rack-space design
- Stack up to 5 units without open spaces between units
- Lightweight (14.6 lbs.)
- Independent power supply for each channel
- Low heat dissipation
- Recessed stepped attenuators
- Comprehensive protection circuitry
- Removable dust filters for easy maintenance
- Optional 250W isolation transformer, model MT-250H (DA-250FH only)
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
| Specification |
|
|---|
| Power Source | 220 - 240V AC or 24V DC | | Rated Output | 120W | | Power Consumption | 124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output) | | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | | Distortion | Under 1% at 1kHz,1/3 rated power | | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | | Phnatom Powe | DC + 21V (MIC 1) | | S/N Ratio | Over 60dB | | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | | Indicator | Power signal, peak | | Finish | Panel: ABS resin, black/Case: Steel plate, black | | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | | Weight | 10kg |
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 1000: 2x500 W/100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 33 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
Reviews
There are no reviews yet.