| Content |
The APG20 is a receiver gateway, designed to be used in combination with the Wall LineInput (WLI) and Wall Microphone Input (WMI) flush mount wall input units. It converts the signal transmitted over UTP CAT5 cabling into signals corresponding Line andMicrophone levels, and makes them available on RCA and XLR connectors. The maximum distance that can be covered between the input unit and the receiver gatewayis 300 m. By applying a ARJ03P junction box halfway the cabling, which provides the requiredpower supply for the input units, the maximum distance can be extended to 600 meters. |
The RM-300MF Fireman's Microphone is designed for exclusive use with the VM-3000 Series. It is equipped with an emergency activation key, permitting pre-recorded evacuation and alert announcements to be activated, and microphone announcement to be made in emergency situations. By connecting the RM-320F Fireman's Microphone Extension to the RM-300MF, the number of function keys can be expanded. The zone selection or failure acknowledgment function can be assigned to such function keys.
| Power Source | 24 V DC (operating range: 15 - 40 V DC, supplied from the VM-3000 system) | | Current Consumption | 120 mA (RM-300MF), 660 mA (with 3 RM-320F connected) | | Frequency Response | 200 Hz - 15 kHz | | Distortion | 1 % or less | | S/N Ratio | 55 dB or more | | Microphone | Unidirectional dynamic microphone with talk key, compressor (on/off switchable) | | Volume Control | Microphone volume control, Buzzer volume control | | Connection Cable | Main line: Shield CPEV cable (each one pair of Audio line, Data line, Power supply line)
or Category 5 Shielded Twisted-Pair straight cable for LAN (CAT5-STP), M3 screw terminal | | Maximum Cable Distance | Total 800 m (874.89 yd) | | No. of Connectable RM-320F | Max. 3 units | | Operation | Emergency key, Evacuate key, Alert key, Emergency reset key, CPU switch, Reset switch | | Indicator | Power indicator, Emergency indicator, Communication failure indicator, CPU OFF indicator,
Evacuation announcement indicator, Alert announcement indicator,
Emergency reset indicator, Microphone in-use indicator,
Emergency broadcast equipment in-use indicator | | Operating Temperature | -5 ℃ to +45 ℃ (23 ゜F to 113 ゜F) | | Operating Humidity | 5 % to 95 %RH (no condensation) | | Finish | ABS resin, blueish gray (PANTONE 538 or its equivalent) | | Dimensions | 200 (W) × 215 (H) × 82.5 (D) mm (7.87" × 8.46" × 3.25“) | | Weight | 1.1 kg (2.43 lb) (with wall mounting bracket unit) | | Accessory | Wall mounting bracket unit …1, Wall mounting screw …2 |
|
- PRIORITY CONTROL It controls the priority of emergency, timer, remote1, remote2, main(normal). - AUTO FIRE SENSOR The fire alarm will be given automatically to the designated areas by detecting fire sensor input. - SPEAKER SWITCHING ON EMERGENCY OR NORMAL(MAIN) You can control the speaker relay on emergency or normal(main) mode by using the speaker switch on front panel. - DISPLAY STATUS You can easily check the priority status. - 2 AND 3 WIRE SPEAKER LINE SYSTEM You can control the speaker line on the 2 wire system or 3 wire system. - EXTENSION FUNCTION You can easily expand by connecting additional ECS-616. ![]()
| ECS-616 | | Priority Control | Emergency >Timer > Remote1 > Remote2 > Main | | Link in/ out Interface | RS-422(19200bps,Data 8bits,Stop 1bit, Non Parity bit, Start1bit) | | Link in/ out interface Distance | 1.2 km | | Operation Temperature | -10 °C ~+ 40 °C | | Power Source | 24V DC | | Power Consumption | 900mA | | Weight | 4.8Kg/10.6Ib | | Dimensions( W x H x D) | 482(W)x 88(H) x 380(D) mm / 19(W)x 3.5(H)x 15(D)in | | ※ Specifications and design subject to change without notice. |
|
The JBL MTC-300T150 150 Watt Transformer is intended for use with 70V or 100V distributed loudspeaker lines. It is ideally suited for the Control Series 300, especially the 300BB12 Backbox which includes a preinstalled mounting location. |
toa-at-100upr Build-in Attenuator with Relay
Toa - 100V installation
Build-in Attenuator with Relay 100 W / 100 V
|
RM-200M - Five/ten zone console for VM-2120/2240 amplfiers
The RM-200M Remote Microphone that allows announcements to be made to any speaker zone and emergency announcements to all zones on a system with the VM-2120/2240 system management amplifiers.
These announcements can be made live or pre-recorded announcements
can be activated. The remote microphone is connected by cable to the
RM-210 Remote Microphone Extension unit.
SPECIFICATIONS:
| Power Requirement | 24 V DC (12-30 V DC), (Supplied from VM-2120/VM-2240 Amplifier or local power suppy.) | | Distortion | Less than 1% | | Frequency Response | 100 - 10,000 Hz | | Distortion | Less than 1% | | Signal-to-Noise Ratio | More than 60 dB | | Audio Output | 0 dB*1, 600 O, balanced | | Microphone | Unidirectional electret condenser microphone, gooseneck type. | | Speaker Zone Control | Zones 1-5 (Zones 1-10 with 2 stacked amplifiers) Groups 1-2, and All-Zone Broadcast | | Emergency Broadcast | Activation of Emergency Broadcast (pre-recorded announcement*2 or live microphone announcement) by Emergency Switch | | Voice Announcement Board Control | Activation of 5 messages*2 | | Number of Connectable Units | Up to 4 | | Communication System | RS-485 | | Volume Control | Microphone volume control | | Connection Cable and Connector Category | 5 STP cable, RJ45 connector | | Communication Distance | 800 m maximum in total | | Finish | ABS resin | | Dimensions | 190 (W) × 75.7 (H) × 21.5 (D) mm (Gooseneck microphone excluded) |
| *1 0 dB = 1 V
*2 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier. |
|
Reviews
There are no reviews yet.