| Content | Designed for sax, toms, brass and percussion, the PRO35 excels in high-SPL applications and is ideal for active stage performances. Its extended frequency response captures subtle nuances of the performance. The included UniMount® clip permits accurate positioning and provides shock resistance while protecting the element. The microphone's cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of the desired sound source.
UniMount® clip permits accurate positioning, provides shock resistance and protects element
Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
Extended frequency response captures subtle nuances of the performance
6' (1.8 m) cable permanently attached between microphone and power module
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Cardioid
Frequency Response: 50-15,000 Hz
Low Frequency Roll Off: 80 Hz, 18 dB/octave
Open Circuit Sensitivity: -45 dB (5.6 mV) re 1V at 1 Pa
Impedance: 250 ohms
Maximum Input Sound Level: 145 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 115 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Switch: Flat, roll-off
Cable: 6.0' (1.8 m) long (permanently attached to microphone), 0.10" (2.6 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
Accessories: AT8418 UniMount® microphone instrument mount; AT8538 power module; soft protective pouch |
Complete With Stereo Bar, Windshield's and Cradle'
The C 414 B-XL II/ST is especially useful for stereo recordings taken from the far field with the inclusion of useful and often valuable room acoustics. The matched pairs consist of two microphones that are within 1 dB to each other in sensitivity and also within 1 dB to each other in the range of 300 Hz to 8,000 Hz of the individual frequency response when used in cardioid mode and are selected from a large quantity of individual microphones using the described criteria by using a proprietary computer program.
Using this matched pair for stereo recordings utilizing various techniques will provide for a good and stable balance without frequency-dependent shifting of the stereo panorama.
The kit comes complete in an all-metal 'Soundtool' Hard Shell road case with 2 x AKG H-85 shock mounts, 2 x W414X external windscreens, an H50 stereo bar and an individually-measured chart showing the response curve of the microphone. See www.dv247.com Alternative Products and Related Products on this page for your options.
The C 414B-XLII has been carefully designed to maintain the legendary sonic character of the C 414 family while integrating new features and performance enhancements made possible by new technology. A classic microphone with a distinctive timbre especially designed for recording of solo vocals and solo instruments.
Whats the difference between the C 414B-XLII and the C 414 B XLS? The main difference between the two current C414 models lies in their frequency responses. The C 414B-XLII has a series of presence rises between 2.5 KHz and 9 KHz. This will make any recording with this microphone brighter or more sibilant than the original sound. This upper mid range boost is quite helpful on vocals and certain instruments such as classical acoustic guitars using nylon or natural strings. The C 414B XLS, see www.dv247.com Alternative Products on this page, has a very flat response that will not color the original sound which is important especially in instrumental recordings. It more suited for general use.
The microphone's 5 pickup patterns are easily selectable via an electronic switch with LED indication and offer the selection of omnidirectional, cardioid wide cardioid, hyper cardioid and figure-eight patterns. The pickup pattern selector switch utilizes a dual-color LED indicator that provides visual indication of the pattern selected and also changes from green to red to indicate if the microphone's output electronics are being overloaded. The pattern selector can also be used to "lock" the microphone's switch settings by pressing and holding it for 3 seconds. On the rear of the microphone, an electronic switch allows the selection of -6, -12 and -18 dB pre-attenuation levels which are accomplished by changing the polarization voltage to the capsule. The C 414B-XLII has switchable bass cut filters of 12 dB-per-octave at 40 Hz and 80 Hz, and a 6 dB-per-octave filter at 160 Hz for control of proximity effect. On-axis sensitivity for all patterns is 23 mV/Pa and its self-noise is an extremely low 6 dB-A.
The C 414B-XLII has a transformerless output and all-metal chassis, making it immune to electrical interference and RF from digital equipment, video monitors and wireless systems.
Features:
- High sensitivity and extremely low self noise
- Five switchable polar patterns for placement and application flexibility
- Two-color LEDs provide quick visual indication of selected polar pattern and output overload
- Elastic capsule suspension greatly minimizes structurally-transmitted noise from chassis vibration
- Supplied with Hard Shell road case with 2 x AKG H-85 shock mounts, 2 x W414X external windscreens and an H50 stereo bar
- High sound pressure level capability, 140 - 158dB, and wide dynamic range
- Completely immune to electrostatic and electro-magnetic interference from digital gear, computer monitors, etc. thanks to solid metal housing and transformerless output stage
- Three switchable bass cut filters and three pre-attenuation pads with LEDs for quick visual indication
- All switchable components operate in low impedance circuits for ultra-high relability even in extremely humid conditions
Specifications:
- Type: 1" large diaphragm pressure gradient microphone
- Polar Patterns: Omnidirectional, wide cardioid, cardioid, hypercardioid, figure eight
- Frequency Range: 20 to 20,000 Hz
- Sensitivity: 23 mV/Pa (-33 dBV) +/-0.5 dB
- Max. SPL: 140/146/152/158 dB SPL (at 0/-6/-12/-18 dB)
- Preattenuation Pad: -6, -12,-18 dB, switchable
- Bass Cut Filter Scope: 12 dB/octave at 40 Hz and 80 Hz; 6 dB/octave at 160 Hz
- Impedance: = 2,200 ohms
- Supply voltage: 48 V phantom power to DIN/IEC
- Current consumption: Approximately 4.5 mA
- Dynamic range: 134 dB minimum
- Environment Temperature range: -10° C to +60° C (14° F to 140° F)
- Relative humidity: 95% (+20° C/68° F), 85% (+60° C/140° F)
- Connector: 3-pin XLR to IEC
- Dimensions: 50 x 38 x 160 mm (2.0 x 1.5 x 6.3 in.)
- Net weight 300 g (10.6 oz.)
|
Audio Frequency Response 50 Hz - 16,000 Hz
Case Material Die cast zinc
Connector Type 3-pin XLR
Element Dynamic
Finish Textured Satin Black
Impedance, Low-Z balanced 600 Ω
Mic Type Instrumental
Open Circuit Voltage 2.2 mV/Pascal
Polar Pattern Supercardioid
Power Requirement Passive
Wired/Wireless Wired
Weight Net 8.32 oz (236 g)
|
Legendary among harmonica players for its classic blues harp sound, the 520D's tradition is carried on by the 520DX "Green Bullet" and has a contoured size and shape that fits perfectly between harmonica and hands. - New volume control knob allows musicians to adjust the volume to fit each musical situation
- New rugged, dynamic cartridge with improved response
- High-impedance, omnidirectional
- Supplied with 1/4 inch connector
- Frequency response: 100 to 5,000 Hz
|
A high performance mini-condenser for sound reinforcement and recording. Great for instruments or drums. The ultra-uniform pickup pattern provides high gain before feedback and excellent rejection of unwanted noise.
Other features include:
- Mew A98D flexible drum mount
- SPL handling to 160dB
- frequency response of 20 to 20,000Hz and included preamplifier
- shock mount and windscreen
|
The E-602 is a cardioid microphone especially suitable for use with bass drums, bass guitar cabs, tubas and other low frequency instruments.
Frequency Response : 20.....16000 Hz
Sensitivity in free field, no load (1kHz) : 1,0 mV/Pa
Min. terminating impedance : 1000 Ohm
Dimensions : d 60 x 153 mm
Weight : w/o cable 550 g
|
Reviews
There are no reviews yet.