| Content |
This elegantly designed bi-directional (figure 8) velocity ribbon microphone is intended for use in modern, state-of-the-art studios as well as private home studios. It offers the unique, pleasing sonic character that is similar to those classic ribbon mics of yesteryear.
The special dual-ribbon design offers a better sensitivity rating than most single ribbon mics on the market. You will also find that it does NOT exhibit the very dark, muted character of some ribbon mics…On the contrary, you will find it to be full-range with a very, natural detailed sound.
The "in-phase” signal is achieved when the microphone is addressed from the front side of the mic. (Where the AVANTONE logo is shown)
Features
• Unique, elegant "retro” body design
• Dual, Low-Mass Ribbon element which enables a much better sensitivity rating than most single ribbon designs
• Fast accurate transient response, ultra-high 148 dB SPL capability, and overall stunning realism
• Figure-8 audio directionality (pickup) pattern via front and rear, with extended sweet spots (as compared to Large Diaphragm condenser mics & single ribbon designs)
• Low residual noise
• No power supply required
• No internal active electronics to overload or produce distortion
• Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability
Applications
Excels with studio solo vocals, group vocals and simultaneous vocal duets. Also recommended for piano, electric guitar cabs and acoustic guitar, orchestral, woodwind & brass instruments as well as hand-percussion instruments.
Very interesting and satisfying tracks can also be achieved using (2) CR-14ʼs for stereo tracking.
Specifications
Ribbon Type: Dual Ribbon / Pure Aluminum / 35mm x 5mm / 2 microns thick
Polar Pattern: Figure-8
Magnets: Rare Earth Neodymium
Frequency Response: 30 -15,000 Hz +/- 3dB
Sensitivity: -52 dBv +/- 2dB Re. (0dB=1V/Pa)
Output Impedance: |
| Large diaphragm cardioid microphone | | Pressure gradient transducer with with one-diaphragm capsule | | Transformerless circuitry | | Extremely low noise: 7 dB-A | | Includes swivel mount | | Straightforward handling for homerecording and professional studios | |
High-quality professional equipment for limited budgets
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 23 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR1) | 17.5 dB | | Equivalent noise level, A-weighted1) | 7 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 76.5 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 87 dB | | Maximum SPL for THD 0.5%2) | 138 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier (A-weighted) | 131 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3 mA | | Matching connector | XLR3F | | Weight | approx. 450 g | | Diameter | 60 mm | | Length | 132 mm |
|
|
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Omnidirectional, wide angle cardioid, cardioid, hypercardioid, figure-8 plus one intermediate position each | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 34/47/62 mV/Pa* | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent SPL CCIR 468-3 | 28/25/23 dB* | | Equivalent SPL DIN/IEC 651 | 16/13/11 dB-A* | | S/N ratio CCIR 468-3 | 66/69/71 dB* | | S/N ratio DIN/IEC 651 | 78/81/83 dB* | | Typical SPL (tube characteristic) | K | | Maximum output voltage | 18 dBu | | Dynamic range of the microphone amplifier cardioid DIN/IEC 651 for | 101 (121) dB | | Powering | Power supply N 149 | | Matching connectors | Microphone DIN 8F, Power supply XLR 3F | | Weight | 730 g | | Diameter | 70 mm | | Length | 201 mm |
* Omnidirectional / cardioid / figure-8
|
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohms | 18 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent SPL CCIR 468-3 | 21 dB | | Equivalent SPL DIN/IEC 651 | 10 dB-A | | S/N ratio CCIR 468-3 | 73 dB | | S/N ratio DIN/IEC 651 | 84 dB | | Maximum SPL for THD 0.5% | 140 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier DIN/IEC 651 | 130 dB | | Supply voltage | 48 V ± 4 V | | Current consumption | 3 mA | | Matching connectors | XLR 3F | | Weight | 480 g | | Diameter | 49 mm | | Length | 175 mm |
|
| Variable large diaphragm microphone | | Pressure-gradient transducer with double membrane capsule | | The studio microphone classic | | Three directional characteristics: omni, cardioid, figure-8 | | Switchable low frequency roll-off | | Switchable 10 dB pre-attenuation | |
Ideal as main and as support microphone in the most differing recording situations
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Omnidirectional, cardioid, figure-8 plus | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 20/28/22 mV/Pa1) | | Rated impedance | 200 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR2) | 26/23/25 dB1) | | Equivalent noise level, A-weighted2) | 15/12/14 dB-A1) | | Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) | 68/71/69 dB1) | | Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) | 79/82/80 dB1) | | Maximum SPL for THD 0.5%3) | 117 dB (cardioid) | | Maximum SPL for THD 0.5% with preattenuation3) | 127 dB | | Maximum output voltage | 390 mV | | Dynamic range of the microphone amplifier (A-weighted) | 105 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 0.8 mA | | Matching connectors | XLR3F | | Weight | 500 g | | Diameter | 56 mm | | Length | 200 mm |
| |
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 13 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent noise level, CCIR1) | 23 dB | | Equivalent noise level, A-weighted1) | 12 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 71 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 82 dB | | Maximum SPL for THD | 110 dB | | Maximum SPL for THD | 129 dB | | Maximum output voltage for THD | -1 dBu | | Dyn. range of the mic. amplifier /A-weighted, 0.5 %2)) | 98 dB | | Dyn. range of the mic. amplifier /A-weighted, 5 %2)) | 117 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3.2 mA | | Matching connector | XLR 3F | | Weight | 825 g | | Diameter | 78 mm | | Length | 165 mm |
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal |
|
|
Reviews
There are no reviews yet.